- 26 Nov, 2015 4 commits
-
-
Martin K. Petersen authored
Commit 4f258a46 ("sd: Fix maximum I/O size for BLOCK_PC requests") had the unfortunate side-effect of removing an implicit clamp to BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer code. This caused problems for some SMR drives. Debugging this issue revealed a few problems with the existing infrastructure since the block layer didn't know how to deal with device-imposed limits, only limits set by the I/O controller. - Introduce a new queue limit, max_dev_sectors, which is used by the ULD to signal the maximum sectors for a REQ_TYPE_FS request. - Ensure that max_dev_sectors is correctly stacked and taken into account when overriding max_sectors through sysfs. - Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer values for later processing. - In sd_revalidate() set the queue's max_dev_sectors based on the MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value is not reported, fall back to a cap based on the CDB TRANSFER LENGTH field size. - In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits VPD--if reported and sane--to signal the preferred device transfer size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS. - blk_limits_max_hw_sectors() is no longer used and can be removed. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581Reviewed-by:
Christoph Hellwig <hch@lst.de> Tested-by: sweeneygj@gmx.com Tested-by:
Arzeets <anatol.pomozov@gmail.com> Tested-by:
David Eisner <david.eisner@oriel.oxon.org> Tested-by:
Mario Kicherer <dev@kicherer.org> Signed-off-by:
-
Douglas Gilbert authored
Ruediger Meier observed a regression with the PREVENT ALLOW MEDIUM REMOVAL command in lk 3.19: http://www.spinics.net/lists/util-linux-ng/msg11448.html Inspection indicated the same regression with VERIFY(10). The patch is against lk 3.19.3 and also works with lk 4.3.0 . With this patch both commands are accepted and do nothing. ChangeLog: - fix the lk 3.19 regression so that the PREVENT ALLOW MEDIUM REMOVAL command is supported once again - same fix for VERIFY(10) Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Hannes Reinicke <hare@suse.de> Reviewed-by:
Ewan Milne <emilne@redhat.com> Signed-off-by:
-
Martin K. Petersen authored
Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Martin K. Petersen authored
A device may report an OPTIMAL UNMAP GRANULARITY and UNMAP GRANULARITY ALIGNMENT in the Block Limits VPD. These parameters describe the device's internal provisioning allocation units. By default the block layer will round and align any discard requests based on these limits. If a device reports LBPRZ=1 to guarantee zeroes after discard, however, it is imperative that the block layer does not leave out any parts of the requested block range. Otherwise the device can not do the required zeroing of any partial allocation units and this can lead to data corruption. Since the dm thinp personality relies on the block layer's current behavior and is unable to deal with partial discard blocks we work around the problem by setting the granularity to match the logical block size when LBPRZ is enabled. Signed-off-by:
-
- 20 Nov, 2015 2 commits
-
-
Arnd Bergmann authored
The hpsa driver recently started using the sas transport class, but it does not ensure that the corresponding code is actually built, which may lead to a link error: drivers/built-in.o: In function `hpsa_free_sas_phy': (.text+0x1ce874): undefined reference to `sas_port_delete_phy' (.text+0x1ce87c): undefined reference to `sas_phy_free' drivers/built-in.o: In function `hpsa_alloc_sas_port': (.text+0x1ceb9c): undefined reference to `sas_port_alloc_num' (.text+0x1ceba8): undefined reference to `sas_port_add' drivers/built-in.o: In function `hpsa_init': (.init.text+0x8838): undefined reference to `sas_attach_transport' (.init.text+0x8868): undefined reference to `sas_release_transport This adds 'select SCSI_SAS_ATTR' in the Kconfig entry, just like we do for all other drivers using those functions. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: d04e62b9 ("hpsa: add in sas transport class") Reviewed-by:
Don Brace <don.brace@pmcs.com> Signed-off-by:
-
Arnd Bergmann authored
The advansys drvier uses the request_dma function that is used on ISA machines for the internal DMA controller, which causes build errors on platforms that have ISA slots but do not provide the ISA DMA API: drivers/scsi/advansys.c: In function 'advansys_board_found': drivers/scsi/advansys.c:11300:10: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration] The problem now showed up in ARM randconfig builds after commit 6571fb3f ("advansys: Update to version 3.5 and remove compilation warning") made it possible to build on platforms that have neither VIRT_TO_BUS nor ISA_DMA_API but that do have ISA. This adds the missing dependency. Signed-off-by:
-
- 19 Nov, 2015 3 commits
-
-
Vitaly Kuznetsov authored
On some host errors storvsc module tries to remove sdev by scheduling a job which does the following: sdev = scsi_device_lookup(wrk->host, 0, 0, wrk->lun); if (sdev) { scsi_remove_device(sdev); scsi_device_put(sdev); } While this code seems correct the following crash is observed: general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC RIP: 0010:[<ffffffff81169979>] [<ffffffff81169979>] bdi_destroy+0x39/0x220 ... [<ffffffff814aecdc>] ? _raw_spin_unlock_irq+0x2c/0x40 [<ffffffff8127b7db>] blk_cleanup_queue+0x17b/0x270 [<ffffffffa00b54c4>] __scsi_remove_device+0x54/0xd0 [scsi_mod] [<ffffffffa00b556b>] scsi_remove_device+0x2b/0x40 [scsi_mod] [<ffffffffa00ec47d>] storvsc_remove_lun+0x3d/0x60 [hv_storvsc] [<ffffffff81080791>] process_one_work+0x1b1/0x530 ... The problem comes with the fact that many such jobs (for the same device) are being scheduled simultaneously. While scsi_remove_device() uses shost->scan_mutex and scsi_device_lookup() will fail for a device in SDEV_DEL state there is no protection against someone who did scsi_device_lookup() before we actually entered __scsi_remove_device(). So the whole scenario looks like that: two callers do simultaneous (or preemption happens) calls to scsi_device_lookup() ant these calls succeed for both of them, after that they try doing scsi_remove_device(). shost->scan_mutex only serializes their calls to __scsi_remove_device() and we end up doing the cleanup path twice. Signed-off-by:Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by:
-
Maurizio Lombardi authored
If cdev_add() returns an error, the code calls cdev_del() passing the STm->cdevs[rew] pointer as parameter; the problem is that the pointer has not been initialized yet. This patch fixes the problem by moving the STm->cdevs[rew] pointer initialization before the call to cdev_add(). It also sets STm->devs[rew] and STm->cdevs[rew] to NULL in case of failure. Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Vitaly Kuznetsov authored
Some host adapters (e.g. Hyper-V storvsc) are known for not respecting the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1: scsi scan: INQUIRY result too short (5), using 36' messages on console. This can be problematic for slow consoles. Introduce short_inquiry flag in struct Scsi_Host to print the message once per host. Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
- 18 Nov, 2015 1 commit
-
-
Arnd Bergmann authored
Building the advansys driver in a big-endian configuration such as ARM allmodconfig shows a warning: drivers/scsi/advansys.c: In function 'adv_build_req': include/uapi/linux/byteorder/big_endian.h:32:26: warning: large integer implicitly truncated to unsigned type [-Woverflow] #define __cpu_to_le32(x) ((__force __le32)__swab32((x))) drivers/scsi/advansys.c:7806:22: note: in expansion of macro 'cpu_to_le32' scsiqp->sense_len = cpu_to_le32(SCSI_SENSE_BUFFERSIZE); It turns out that the commit that introduced this used the cpu_to_le32() incorrectly on an 8-bit field, which results in the sense_len to always be set to zero, as the SCSI_SENSE_BUFFERSIZE value gets moved to upper byte of the 32-bit intermediate. This removes the cpu_to_le32() call to restore the original version. I found this only by looking at the compiler output and have not done a full review for possible further endianess bugs in the same driver. Signed-off-by:
-
- 17 Nov, 2015 1 commit
-
-
Bart Van Assche authored
This patch fixes the following kernel bug: kernel:BUG: rwlock recursion on CPU#2, insmod/39333, ffff8803e998cb28 kernel: Call Trace: kernel: [<ffffffff812bce44>] dump_stack+0x48/0x64 kernel: [<ffffffff810a8047>] rwlock_bug+0x67/0x70 kernel: [<ffffffff810a833a>] do_raw_write_lock+0x8a/0xa0 kernel: [<ffffffff815f3033>] _raw_write_lock_irqsave+0x63/0x80 kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx] kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx] kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx] kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx] kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx] kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx] kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx] kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx] kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx] kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx] kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx] kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx] kernel: [<ffffffffa07c964e>] qla2x00_probe_one+0xefe/0x2130 [qla2xxx] kernel: [<ffffffff8130052c>] local_pci_probe+0x4c/0xa0 kernel: [<ffffffff81300603>] pci_call_probe+0x83/0xa0 kernel: [<ffffffff813008cf>] pci_device_probe+0x7f/0xb0 kernel: [<ffffffff813e2e83>] really_probe+0x133/0x390 kernel: [<ffffffff813e3139>] driver_probe_device+0x59/0xd0 kernel: [<ffffffff813e3251>] __driver_attach+0xa1/0xb0 kernel: [<ffffffff813e0cdd>] bus_for_each_dev+0x8d/0xb0 kernel: [<ffffffff813e28ee>] driver_attach+0x1e/0x20 kernel: [<ffffffff813e2252>] bus_add_driver+0x1d2/0x290 kernel: [<ffffffff813e3970>] driver_register+0x60/0xe0 kernel: [<ffffffff813009e4>] __pci_register_driver+0x64/0x70 kernel: [<ffffffffa04bc1cb>] qla2x00_module_init+0x1cb/0x21b [qla2xxx] kernel: [<ffffffff8100027d>] do_one_initcall+0xad/0x1c0 kernel: [<ffffffff810e2859>] do_init_module+0x69/0x210 kernel: [<ffffffff810e4e5c>] load_module+0x5cc/0x750 kernel: [<ffffffff810e5162>] SyS_init_module+0x92/0xc0 kernel: [<ffffffff815f37d7>] entry_SYSCALL_64_fastpath+0x12/0x6f Fixes: 8dfa4b5a ("qla2xxx: Fix sparse annotation") Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reported-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Tested-by:
Chad Dupuis <chad.dupuis@qlogic.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Xose Vazquez Perez <xose.vazquez@gmail.com> Cc: stable <stable@vger.kernel.org> # v4.3+ Signed-off-by:
-
- 13 Nov, 2015 3 commits
-
-
Dan Carpenter authored
HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was intended here instead of logical &&. This bug is essentially harmless, it means that sometimes we don't print a warning message which we wanted to print. Fixes: c2adae44 ('hpsa: disable report lun data caching') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Dan Carpenter authored
There is a static checker warning here because "val" is controlled by the user and we have a upper bound on it but allow negative numbers. "val" appears to be a timeout in usec so this bug probably means we have a longer timeout than we should. Let's fix this by changing "val" to unsigned. Signed-off-by:
Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by:
-
Sreekanth Reddy authored
Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request message, check whether TLR is enabled on the drive using 'sas_is_tlr_enabled' API. Actually in the driver code, driver is using below API's 1. sas_enable_tlr() - to enable the TLR 2. sas_disable_tlr() - to disable the TLR 3. sas_is_tlr_enabled() - to check whether TLR is enabled or not. but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API, instead we checking for TLR bit from flag field of driver's 'struct MPT3SAS_DEVIC' structure. which is corrected with this patch. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by:
-
- 12 Nov, 2015 14 commits
-
-
Gabriel Krisman Bertazi authored
According to SPC-4, in a Mode Select, the PS bit in Mode Pages is reserved and must be set to 0 by the driver. In the sd implementation, function cache_type_store does a Mode Sense, which might set the PS bit on the read buffer, followed by a Mode Select, which receives the same buffer, without explicitly clearing the PS bit. So, in cases where target supports saving the Mode Page to a non-volatile location, we end up doing a Mode Select with the PS bit set, which could cause an illegal request error if the target is checking this. This was observed on a new firmware change, which was subsequently reverted, but this changes sd.c to be more compliant with SPC-4. This patch clears the PS bit in the buffer returned by Mode Select, right before it is used in the Mode Select command. Signed-off-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by:
-
Laurent Vivier authored
As defined in 4.6.9 of SAM-4, the encoding of LUN is on 5 bits (max_lun=32) and the current value is only 8. Set max_lun to IBMVSCSI_MAX_LUN (32). Signed-off-by:
Laurent Vivier <lvivier@redhat.com> Signed-off-by:
-
Laurent Vivier authored
As devices with values greater than that are silently ignored, this gives some hints to the sys admin to know why he doesn't see his devices... Signed-off-by:
-
Dan Carpenter authored
There is a static checker warning here because "bytes" is controlled by the user and we cap the upper bound with min() but allow negatives. Negative bytes will result in some nasty warning messages but are not super harmful. Anyway, no one needs negative bytes so let's just check for it and return NULL. Signed-off-by:
-
Alison Schofield authored
Replace the use of struct timeval and do_gettimeofday() with 64 bit ktime_get_real_seconds. Prevents 32-bit type overflow in year 2038 on 32-bit systems. Driver was using the seconds portion of struct timeval (.tv_secs) to pass a millseconds timestamp to the firmware. This change maintains that same behavior using ktime_get_real_seconds. The structure used to pass the timestamp to firmware is 48 bits and works fine as long as the top 16 bits are zero and they will be zero for a long time..ie. thousands of years. Alternative Change: Add sub second granularity to timestamp As noted above, the driver only used the seconds portion of timeval, ignores the microseconds portion, and by multiplying by 1000 effectively does a <<10 and always writes zero into timestamp[0]. The alternative change would pass all the bits to the firmware: struct timespec64 ts; ktime_get_real_ts64(&ts); timestamp = ts.tv_sec * MSEC_PER_SEC + ts.tv_nsec / NSEC_PER_MSEC; Signed-off-by:Alison Schofield <amsfield22@gmail.com> Reviewed-by:
-
Tina Ruchandani authored
struct mvumi_hs_page2 stores a "seconds_since1970" field which is of type u64. It is however, written to, using 'struct timeval' which has a 32-bit seconds field and whose value will overflow in year 2038. This patch uses ktime_get_real_seconds() instead since it provides a 64-bit seconds value, which is 2038 safe. Signed-off-by:
Tina Ruchandani <ruchandani.tina@gmail.com> Reviewed-by:
-
Tim Gardner authored
drivers/scsi/be2iscsi/be_main.c: In function 'be_sgl_create_contiguous': drivers/scsi/be2iscsi/be_main.c:3187:18: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses] WARN_ON(!length > 0); gcc version 5.2.1 Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Cc: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com> Cc: Minh Tran <minh.tran@avagotech.com> Cc: John Soni Jose <sony.john-n@avagotech.com> Cc: "James E.J. Bottomley" <JBottomley@odin.com> Reported-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Manoj Kumar <manoj@linux.vnet.ibm.com> Signed-off-by:
-
Vitaly Kuznetsov authored
The only user of scsi_prep_async_scan() is scsi_scan_host() and it handles the situation correctly. Move 'called twice' reporting to debug level as well. The issue is observed on Hyper-V: on any device add/remove event storvsc driver calls scsi_scan_host() and in case previous scan is still running we get the message and stack dump on console. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Alex Ng <alexng@microsoft.com> Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt3sas driver version to 09.102.00.00 Signed-off-by:
-
Sreekanth Reddy authored
Modified the mpt3sas driver to have a single driver module which supports both SAS 2.0 & SAS 3.0 HBA devices. * Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table. * Created two separate SCSI host templates for SAS2 and SAS3 HBAs so that, during the driver load time driver can use corresponding host template(based the pci device ID) while registering a scsi host adapter instance for that pci device. * Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for SAS3 HBAs. Also updated the code to make sure that mpt2ctl device processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl device processes only those ioctl cmds issued for the SAS3 HBAs. * Added separate indexing for SAS2 and SAS3 HBAs. * Replaced compile time check 'MPT2SAS_SCSI' to run time check 'hba_mpi_version_belonged' whereever needed. * Aliased this merged driver to mpt2sas using MODULE_ALIAS. * Moved global varaible 'driver_name' to per adapter instance variable. * Created two raid function template and used corresponding raid function templates based on the run time check 'hba_mpi_version_belonged'. * Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and renamed it as mpt3sas_warpdrive.c. * Also renamed the functions in mpt3sas_warpdrive.c file to follow current driver function name convention. * Updated the Makefile to build mpt3sas_warpdrive.o file for these WarpDrive-specific functions. * Also in function mpt3sas_setup_direct_io(), used sector_div() API instead of division operator (which gives compilation errors on 32 bit machines). * Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file. * Added module parameter 'hbas_to_enumerate' which permits using this merged driver as a legacy mpt2sas driver or as a legacy mpt3sas driver. Here are the available options for this module parameter: 0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs 1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs 2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs * Removed mpt2sas entries from SCSI's Kconfig and Makefile files. Signed-off-by:
-
Sreekanth Reddy authored
Bump the mpt2sas driver version to 20.102.00.00 and Bump the mpt3sas driver version to 9.101.00.00. Signed-off-by:
-
Sreekanth Reddy authored
setpci reset on nytro warpdrive card along with sysfs access and cli ioctl access resulted in kernel oops 1. pci_access_mutex lock added to provide synchronization between IOCTL, sysfs, PCI resource handling path 2. gioc_lock spinlock to protect list operations over multiple controllers This patch is ported from commit 6229b414 ("mpt2sas: setpci reset kernel oops fix"). Signed-off-by:
-
Sreekanth Reddy authored
Added OEM Gen2 PnP ID branding names from mpt2sas driver. Signed-off-by:
-
Sreekanth Reddy authored
The fw_event_work struct is concurrently referenced at shutdown. Add a refcount to protect it and refactor the code to use it. Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no longer iterates over the list without holding the lock since _firmware_event_work() concurrently deletes items from the list. This patch is ported from commit 008549f6 ("mpt2sas: Refcount fw_events and fix unsafe list usage"). These changes are also required for mpt3sas. Signed-off-by:
-
- 11 Nov, 2015 12 commits
-
-
Sreekanth Reddy authored
sas_device objects can be referenced concurrently throughout the driver. We need a way to make sure threads can't delete them out from under each other. This patch adds the refcount and refactors the code to use it. Additionally, we cannot iterate over the sas_device_list without holding the lock or we risk corrupting random memory if items are added or deleted as we iterate. This patch refactors _scsih_probe_sas() to use the sas_device_list in a safe way. This patch is ported from the following mpt2sas driver commit d224fe0d ("mpt2sas: Refcount sas_device objects and fix unsafe list usage"). Signed-off-by:
-
Sreekanth Reddy authored
A new sysfs shost attribute called "BMR_status" is implemented to report Backup Rail Monitor status. This attribute is located in: /sys/class/scsi_host/host#/BMR_status When reading this adapter attribute, the driver will output the state of GPIO[24]. It returns "0" if BMR is healthy and "1" for failure. If it returns an empty string then it means that there was an error while obtaining the BMR status. Check dmesg for what error has occurred. This sysfs shost attribute is mainly for WarpDrive controllers. This commit is a port of 6c265660 ("mpt2sas: Provide sysfs attribute to report Backup Rail Monitor Status"). Signed-off-by: -
Sreekanth Reddy authored
Ported the following list of WarpDrive-specific patches: 1. commit 0bdccdb0 ("mpt2sas: WarpDrive New product SSS6200 support added") 2. commit 82a45258 ("mpt2sas: WarpDrive Infinite command retries due to wrong scsi command entry in MPI message") 3. commit ba96bd0b ("mpt2sas: Support for greater than 2TB capacity WarpDrive") 4. commit 4da7af94 ("mpt2sas: Do not retry a timed out direct IO for Warpdrive") 5. commit daeaa9df ("mpt2sas: Avoid type casting for direct I/O commands"). Also set the mpt2_ioctl_iocinfo adapter_type to: 1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs 2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive 3. MPT2_IOCTL_INTERFACE_SAS2 for other Gen2 HBAs Signed-off-by:
-
Sreekanth Reddy authored
This patch stops the driver to invoke kthread (which remove the dead ioc) for some time while EEH recovery has started. This patch is a port of commit b4730fb6 ("mpt2sas: fix for driver fails EEH, recovery from injected pci bus error")'. Signed-off-by:
-
Sreekanth Reddy authored
1. Do not enable MSI-X vectors for SAS2008 B0 controllers 2. Enable a single MSI-X vector for the following controller: a. SAS2004 b. SAS2008 c. SAS2008_1 d. SAS2008_2 e. SAS2008_3 f. SAS2116_1 g. SAS2116_2 3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors) for Gen3 Invader/Fury C0 and above revision HBAs 4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors) for all Intruder and Cutlass HBAs Signed-off-by:
-
Sreekanth Reddy authored
Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers since they don't support it. Also enable fast_path only for SAS3 HBAs. Signed-off-by:
-
Sreekanth Reddy authored
Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE scatter-gather lists. Modify the common code part in such a way that it will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2 HBAs. Signed-off-by:
-
Sreekanth Reddy authored
Currently there is a logging level option provided for each of our drivers in the kernel configuration utility. Users can enable this option to get more verbose information. By default it is enabled. Only when this option is enabled will the functions which display the required information get compiled in. As we are merging the both drivers we can no longer provide this configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig and unconditionally enable logging (by removing the #ifdef CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all functions which are defined to display more verbose information get compiled in. Signed-off-by:
-
Sreekanth Reddy authored
1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each individual generation driver functionality at runtime. 2. Declare global variable 'driver_name' and use this variable while reserving PCI regions and while allocating the IRQs. Signed-off-by:
-
Sreekanth Reddy authored
Remove .c and .h files which are no longer needed from mpt2sas driver. We are reusing this code from mpt3sas. Signed-off-by:
-
Sreekanth Reddy authored
1. Create a mpt2sas_module.c file for mpt2sas where GEN2 HBA devices register with PCI, SML, IOCTL subsystems. 2. Updated the Makefile to use the object files from mpt3sas folder. 3. Defined a compilation flag SCSI_MPT2SAS which can be used to not include those sections of code from mpt3sas driver which are not required for mpt2sas driver. 4. Inherited automatic diag buffer feature from mpt3sas driver. Signed-off-by:
-
Sreekanth Reddy authored
Created a mpt3sas_module.c file for mpt3sas driver where it can register SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the corresponding interfaces from mpt3sas_scsih.c file. Signed-off-by:
-
