This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: David S. Miller <davem@davemloft.net>

Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>>         Number of maximum addresses per interface.  0 disables limitation.
>>         It is recommended not set too large value (or 0) because it would
>>         be too easy way to crash kernel to allow to create too much of
>>         autoconfigured addresses.
           ^^^^^^^^^^^^^^

>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.

It did mention autoconfigured in the text, but the below makes it more obvious.

More clearly document IPv6 max_addresses parameter.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I am no longer with Marvell.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.

Based on a review of the chip datasheets and advice from the designer
of these boards:

- Raise the maximum board temperatures to the specified maximum ambient
  temperatures for their PHYs plus the expected temperature bias of the
  board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol.  It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wireless sysfs methods like the rest of the networking sysfs
methods are removed with the rtnl_lock held and block until
the existing methods stop executing.  So use rtnl_trylock
and restart_syscall so that the code continues to work.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuck.  It turns out that when we restart sysctls we were restarting
with the values already changed.  Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.

I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.

One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: 8250: add serial transmitter fully empty test

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: gadget: fix EEM gadget CRC usage
  USB: otg Kconfig: let USB_OTG_UTILS select USB_ULPI option
  USB: g_multi: fix CONFIG_USB_G_MULTI_RNDIS usage
  kfifo: Don't use integer as NULL pointer
  USB: FHCI: Fix build after kfifo rework
  kfifo: Make kfifo_initialized work after kfifo_free
  USB: serial: add usbid for dell wwan card to sierra.c
  USB: SIS USB2VGA DRIVER: support KAIREN's USB VGA adaptor USB20SVGA-MB-PLUS
  USB: ehci: phy low power mode bug fixing
  USB: s3c-hsotg: Export usb_gadget_register_driver()
  USB: r8a66597-udc: Prototype IS_ERR() and PTR_ERR()
  USB: ftdi_sio: add device IDs (several ELV, one Mindstorms NXT)
  USB: storage: Remove unneeded SC/PR from unusual_devs.h
  USB: ftdi_sio: new device id for papouch AD4USB
  USB: usbfs: properly clean up the as structure on error paths
  USB: usbfs: only copy the actual data received

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  class: Free the class private data in class_release
  sysfs: sysfs_sd_setattr set iattrs unconditionally

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
  be2net: set proper value to version field in req hdr
  xfrm: Fix xfrm_state_clone leak
  ipcomp: Avoid duplicate calls to ipcomp_destroy
  ethtool: allow non-admin user to read GRO settings.
  ixgbe: fix WOL register setup for 82599
  ixgbe: Fix - Do not allow Rx FC on 82598 at 1G due to errata
  sfc: Fix SFE4002 initialisation
  mac80211: fix handling of null-rate control in rate_control_get_rate
  inet: Remove bogus IGMPv3 report handling
  iwlwifi: fix AMSDU Rx after paged Rx patch
  tcp: fix ICMP-RTO war
  via-velocity: Fix races on shared interrupts
  via-velocity: Take spinlock on set coalesce
  via-velocity: Remove unused IRQ status parameter from rx_srv and tx_srv
  rtl8187: Add new device ID
  iwmc3200wifi: Test of wrong pointer after kzalloc in iwm_mlme_update_bss_table()
  ath9k: Fix sequence numbers for PAE frames
  mac80211: fix deferred hardware scan requests
  iwlwifi: Fix to set correct ht configuration
  mac80211: Fix probe request filtering in IBSS mode
  ...

When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.

The transmitter should not be turned off before all characters have been
transmitted.  serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.

===

Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:

I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard.  This type of expansion board is very common.

"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.

The NetMos device does it slightly different

I believe that the TEMT bit is coupled to the shift register.  The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.

My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.

Alan:

  We may yet need to quirk this but now we know which chips we have a
  way to do that should we find this breaks some other 8250 clone with
  dodgy THRE.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix a memory leak by freeing the memory allocated in __class_register
for the class private data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There is currently a bug in sysfs_sd_setattr inherited from
sysfs_setattr in 2.6.32 where the first time we set the attributes
on a sysfs file we allocate backing store but do not set the
backing store attributes.  Resulting in overly restrictive
permissions on sysfs files.

The fix is to simply modify the code so that it always executes
when we update the sysfs attributes, as we did in 2.6.31 and earlier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

eem_wrap() is sending a sentinel CRC, but it didn't indicate that to
the host, it should zero bit 14 (bmCRC) in the EEM packet header,
instead of setting it.

Also remove a redundant crc calculation in eem_unwrap().
Signed-off-by: Steve Longerbeam <stevel@netspectrum.com>
Acked-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.

Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'

This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

g_multi used CONFIG_USB_ETH_RNDIS to check if RNDIS option was requested
where it should check for CONFIG_USB_G_MULTI_RNDIS.  As a result, RNDIS
was never present in g_multi regardless of configuration.

This fixes changes made in commit 396cda90.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes following sparse warnings:

include/linux/kfifo.h:127:25: warning: Using plain integer as NULL pointer
kernel/kfifo.c:83:21: warning: Using plain integer as NULL pointer
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

After kfifo rework FHCI fails to build:

  CC      drivers/usb/host/fhci-tds.o
drivers/usb/host/fhci-tds.c: In function 'fhci_ep0_free':
drivers/usb/host/fhci-tds.c:108: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:118: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:128: error: used struct type value where scalar is required

This is because kfifos are no longer pointers in the ep struct.
So, instead of checking the pointers, we should now check if kfifo
is initialized.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

After kfifo rework it's no longer possible to reliably know if kfifo is
usable, since after kfifo_free(), kfifo_initialized() would still return
true. The correct behaviour is needed for at least FHCI USB driver.

This patch fixes the issue by resetting the kfifo to zero values (the
same approach is used in kfifo_alloc() if allocation failed).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port.  I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds the USB product ID of KAIREN's USB VGA Adaptor,
USB20SVGA-MB-PLUS, to sisusbvga work with it.
Signed-off-by: Tanaka Akira <akr@fsij.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1. There are two msleep calls inside two spin lock sections, need to unlock
   and lock again after msleep.
2. Save a extra status reg setting.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB gadget controller drivers normally export their driver registration
function, allowing modular builds of the individual gadget drivers so
do so for s3c-hsotg, fixing builds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The build of r8a66597-udc was failing on ARM since IS_ERR() and
PTR_ERR() weren't protyped.  Presumably err.h is being pulled in by
another header on other platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
  them by default." comment (we simply add _all_ known devices - an
  enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR

The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes the subclass and protocol entries from a Microtech
entry in unusual_devs.h. This was reported by <ryck@pacbell.net>.

Greg, please apply.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c

AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB.  datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdfSigned-off-by: Radek Liboska <liboska@uochb.cas.cz>

I notice that the processcompl_compat() function seems to be leaking the
'struct async *as' in the error paths. 

I think that the calling convention is fundamentally buggered. The
caller is the one that did the "reap_as()" to get the as thing, the
caller should be the one to free it too. 

Freeing it in the caller also means that it very clearly always gets
freed, and avoids the need for any "free in the error case too".

From: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Marcus Meissner <meissner@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We need to only copy the data received by the device to userspace, not
the whole kernel buffer, which can contain "stale" data.

Thanks to Marcus Meissner for pointing this out and testing the fix.
Reported-by: Marcus Meissner <meissner@suse.de>
Tested-by: Marcus Meissner <meissner@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Before sending a command to the ASIC, set version properly.
This is necessary for the ARM firmware to send correct data to the driver.
This also fixes a bug in certain skews of the ASIC where the statistics
are misreported.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm_state_clone calls kfree instead of xfrm_state_put to free
a failed state.  Depending on the state of the failed state, it
can cause leaks to things like module references.

All states should be freed by xfrm_state_put past the point of
xfrm_init_state.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ipcomp_tunnel_attach fails we will call ipcomp_destroy twice.
This may lead to double-frees on certain structures.

As there is no reason to explicitly call ipcomp_destroy, this patch
removes it from ipcomp*.c and lets the standard xfrm_state destruction
take place.

This is based on the discovery and patch by Alexey Dobriyan.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like an oversight in GRO design.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
  dm: sysfs revert add empty release function to avoid debug warning
  dm mpath: fix stall when requeueing io
  dm raid1: fix null pointer dereference in suspend
  dm raid1: fail writes if errors are not handled and log fails
  dm log: userspace fix overhead_size calcuations
  dm snapshot: persistent annotate work_queue as on stack
  dm stripe: avoid divide by zero with invalid stripe count

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] preserve personality flag bits across exec

Revert commit d2bb7df8 at Greg's request.

    Author: Milan Broz <mbroz@redhat.com>
    Date:   Thu Dec 10 23:51:53 2009 +0000

    dm: sysfs add empty release function to avoid debug warning

    This patch just removes an unnecessary warning:
     kobject: 'dm': does not have a release() function,
     it is broken and must be fixed.

    The kobject is embedded in mapped device struct, so
    code does not need to release memory explicitly here.

Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch fixes the problem that system may stall if target's ->map_rq
returns DM_MAPIO_REQUEUE in map_request().
E.g. stall happens on 1 CPU box when a dm-mpath device with queue_if_no_path
     bounces between all-paths-down and paths-up on I/O load.

When target's ->map_rq returns DM_MAPIO_REQUEUE, map_request() requeues
the request and returns to dm_request_fn().  Then, dm_request_fn()
doesn't exit the I/O dispatching loop and continues processing
the requeued request again.
This map and requeue loop can be done with interrupt disabled,
so 1 CPU system can be stalled if this situation happens.

For example, commands below can stall my 1 CPU box within 1 minute or so:
  # dmsetup table mp
  mp: 0 2097152 multipath 1 queue_if_no_path 0 1 1 service-time 0 1 2 8:144 1 1
  # while true; do dd if=/dev/mapper/mp of=/dev/null bs=1M count=100; done &
  # while true; do \
  > dmsetup message mp 0 "fail_path 8:144" \
  > dmsetup suspend --noflush mp \
  > dmsetup resume mp \
  > dmsetup message mp 0 "reinstate_path 8:144" \
  > done

To fix the problem above, this patch changes dm_request_fn() to exit
the I/O dispatching loop once if a request is requeued in map_request().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

When suspending a failed mirror, bios are completed by mirror_end_io() and
__rh_lookup() in dm_rh_dec() returns NULL where a non-NULL return value is
required by design.  Fix this by not changing the state of the recovery failed
region from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end().

Issue

On 2.6.33-rc1 kernel, I hit the bug when I suspended the failed
mirror by dmsetup command.

BUG: unable to handle kernel NULL pointer dereference at 00000020
IP: [<f94f38e2>] dm_rh_dec+0x35/0xa1 [dm_region_hash]
...
EIP: 0060:[<f94f38e2>] EFLAGS: 00010046 CPU: 0
EIP is at dm_rh_dec+0x35/0xa1 [dm_region_hash]
EAX: 00000286 EBX: 00000000 ECX: 00000286 EDX: 00000000
ESI: eff79eac EDI: eff79e80 EBP: f6915cd4 ESP: f6915cc4
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process dmsetup (pid: 2849, ti=f6914000 task=eff03e80 task.ti=f6914000)
 ...
Call Trace:
 [<f9530af6>] ? mirror_end_io+0x53/0x1b1 [dm_mirror]
 [<f9413104>] ? clone_endio+0x4d/0xa2 [dm_mod]
 [<f9530aa3>] ? mirror_end_io+0x0/0x1b1 [dm_mirror]
 [<f94130b7>] ? clone_endio+0x0/0xa2 [dm_mod]
 [<c02d6bcb>] ? bio_endio+0x28/0x2b
 [<f952f303>] ? hold_bio+0x2d/0x62 [dm_mirror]
 [<f952f942>] ? mirror_presuspend+0xeb/0xf7 [dm_mirror]
 [<c02aa3e2>] ? vmap_page_range+0xb/0xd
 [<f9414c8d>] ? suspend_targets+0x2d/0x3b [dm_mod]
 [<f9414ca9>] ? dm_table_presuspend_targets+0xe/0x10 [dm_mod]
 [<f941456f>] ? dm_suspend+0x4d/0x150 [dm_mod]
 [<f941767d>] ? dev_suspend+0x55/0x18a [dm_mod]
 [<c0343762>] ? _copy_from_user+0x42/0x56
 [<f9417fb0>] ? dm_ctl_ioctl+0x22c/0x281 [dm_mod]
 [<f9417628>] ? dev_suspend+0x0/0x18a [dm_mod]
 [<f9417d84>] ? dm_ctl_ioctl+0x0/0x281 [dm_mod]
 [<c02c3c4b>] ? vfs_ioctl+0x22/0x85
 [<c02c422c>] ? do_vfs_ioctl+0x4cb/0x516
 [<c02c42b7>] ? sys_ioctl+0x40/0x5a
 [<c0202858>] ? sysenter_do_call+0x12/0x28

Analysis

When recovery process of a region failed, dm_rh_recovery_end() function
changes the state of the region from RM_RH_RECOVERING to DM_RH_NOSYNC.
When recovery_complete() is executed between dm_rh_update_states() and
dm_writes() in do_mirror(), bios are processed with the region state,
DM_RH_NOSYNC. However, the region data is freed without checking its
pending count when dm_rh_update_states() is called next time.

When bios are finished by mirror_end_io(), __rh_lookup() in dm_rh_dec()
returns NULL even though a valid return value are expected.

Solution

Remove the state change of the recovery failed region from DM_RH_RECOVERING
to DM_RH_NOSYNC in dm_rh_recovery_end(). We can remove the state change
because:

  - If the region data has been released by dm_rh_update_states(),
    a new region data is created with the state of DM_RH_NOSYNC, and
    bios are processed according to the DM_RH_NOSYNC state.

  - If the region data has not been released by dm_rh_update_states(),
    a state of the region is DM_RH_RECOVERING and bios are put in the
    delayed_bio list.

The flag change from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end()
was added in the following commit:
  dm raid1: handle resync failures
  author  Jonathan Brassow <jbrassow@redhat.com>
    Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)
  http://git.kernel.org/linus/f44db678edcc6f4c2779ac43f63f0b9dfa28b724Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>