Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.

iproute2 may be built without libmnl support, in which case the extack
messages will not be reported.  Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2018-01-23

This series contains updates to i40e and i40evf only.

Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.

Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.

Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts.  This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.

Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.

Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.

Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed.  Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.

Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.

Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Davide Caratti says:

====================
net/sched: remove spinlock from 'csum' action

Similarly to what has been done earlier with other actions [1][2], this
series tries to improve the performance of 'csum' tc action, removing a
spinlock in the data path. Patch 1 lets act_csum use per-CPU counters;
patch 2 removes spin_{,un}lock_bh() calls from the act() method.

test procedure (using pktgen from https://github.com/netoptimizer):

 # ip link add name eth1 type dummy
 # ip link set dev eth1 up
 # tc qdisc add dev eth1 root handle 1: prio
 # for a in pass drop; do
 > tc filter del dev eth1 parent 1: pref 10 matchall action csum udp
 > tc filter add dev eth1 parent 1: pref 10 matchall action csum udp $a
 > for n in 2 4; do
 > ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $n -n 1000000 -i eth1
 > done
 > done

test results:

      |    |  before patch   |   after patch
  $a  | $n | avg. pps/thread | avg. pps/thread
 -----+----+-----------------+----------------
 pass |  2 |    1671463 ± 4% |    1920789 ± 3%
 pass |  4 |     648797 ± 1% |     738190 ± 1%
 drop |  2 |    3212692 ± 2% |    3719811 ± 2%
 drop |  4 |    1078824 ± 1% |    1328099 ± 1%

references:

[1] https://www.spinics.net/lists/netdev/msg334760.html
[2] https://www.spinics.net/lists/netdev/msg465862.html

v3 changes:
 - use rtnl_dereference() in place of rcu_dereference() in tcf_csum_dump()

v2 changes:
 - add 'drop' test, it produces more contentions
 - use RCU-protected struct to store 'action' and 'update_flags', to avoid
   reading the values from subsequent configurations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

use RCU instead of spin_{,unlock}_bh() to protect concurrent read/write on
act_csum configuration, to reduce the effects of contention in the data
path when multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It takes 1sec for bond link down notification to hit user-space
when all slaves of the bond go down. 1sec is too long for
protocol daemons in user-space relying on bond notification
to recover (eg: multichassis lag implementations in user-space).
Since the link event code already marks team device port link events
 as urgent, this patch moves the code to cover all lag ports and master.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-01-23

This series contains updates to ixgbe only.

Shannon Nelson provides an implementation of the ipsec hardware offload
feature for the ixgbe driver for these devices: x540, x550, 82599.

The ixgbe NICs support ipsec offload for 1024 Rx and 1024 Tx Security
Associations (SAs), using up to 128 inbound IP addresses, and using the
rfc4106(gcm(aes)) encryption.  This code does not yet support checksum
offload, or TSO in conjunction with the ipsec offload - those will be
added in the future.

This code shows improvements in both packet throughput and CPU utilization.
For example, here are some quicky numbers that show the magnitude of the
performance gain on a single run of "iperf -c <dest>" with the ipsec
offload on both ends of a point-to-point connection:

	9.4 Gbps - normal case
	7.6 Gbps - ipsec with offload
	343 Mbps - ipsec no offload
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sebastian Reichel says:

====================
GEHC Bx50 Switch Support

This adds support for the internal switch found in GE Healthcare
B450v3, B650v3 and B850v3. All devices use a GPIO bitbanged MDIO
bus to communicate with the switch and a PCIe based network card
for exchanging network data. The cpu network data link requires,
that the switch's internal phy interface is enabled, so support
for that is added by the first patch in this series.

The patch series is based on v4.15-rc8.

Changes since PATCHv4:
 * Introduce dsa_port_link_(un)register_of and mark the fixed
   variant static.
 * Update patch description to describe the phy<->phy connection
   from i210 to the Marvell switch
Changes since PATCHv3:
 * Enable the phy in dsa_port_setup() instead of abusing the
   fixed link setup function
Changes since PATCHv2:
 * Add phy nodes to switch in bx50.dtsi and reference them
   from switch ports
 * Enable cpu-port's phy based on 'phy-handle' instead of 'phy-mode'
Changes since PATCHv1:
 * Use 'marvell,mv88e6085' instead of introducing compatible
   string for mv88e6240.
 * Fix indention of DT nodes
 * Only enable 'cpu' phy, if explicitly set to "internal".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0  Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0  Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.

The PCI bus configuration has been written using the following
information:

root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0  Intel Corporation I210 Gigabit Network Connection
                                        +-02.0-[04]----00.0  Intel Corporation I210 Gigabit Network Connection
                                        \-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3,  B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang.  This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.

Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.

If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.

This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.

The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts.  By triggering a SW
interrupt, interrupts are forced on.  If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.

This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.

Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.

This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.

The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>

With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits.  While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info.  Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On a chip reset most of the table contents are lost, so must be
restored.  This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware.  We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.

The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle.  However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add in the code for running and stopping the hardware ipsec
encryption/decryption engine.  It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:

 1) Fix divide by zero in mlx5, from Talut Batheesh.

 2) Guard against invalid GSO packets coming from untrusted guests and
    arriving in qdisc_pkt_len_init(), from Eric Dumazet.

 3) Similarly add such protection to the various protocol GSO handlers.
    From Willem de Bruijn.

 4) Fix regression added to IGMP source address checking for IGMPv3
    reports, from Felix Feitkau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tls: Correct length of scatterlist in tls_sw_sendpage
  be2net: restore properly promisc mode after queues reconfiguration
  net: igmp: fix source address check for IGMPv3 reports
  gso: validate gso_type in GSO handlers
  net: qdisc_pkt_len_init() should be more robust
  ibmvnic: Allocate and request vpd in init_resources
  ibmvnic: Revert to previous mtu when unsupported value requested
  ibmvnic: Modify buffer size and number of queues on failover
  rds: tcp: compute m_ack_seq as offset from ->write_seq
  usbnet: silence an unnecessary warning
  cxgb4: fix endianness for vlan value in cxgb4_tc_flower
  cxgb4: set filter type to 1 for ETH_P_IPV6
  net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare

Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization.  Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 97a6ec4a ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.

A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.

Note that this issue doesn't affect net.git yet.

Fixes: 97a6ec4a ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.

Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>