Jiri Pirko says:

====================
mlxsw: couple of fixes

Couple of fixes from Ido and myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.

Fixes: 0293038e ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 14d39461 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.

However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.

Fixes: 14d39461 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.

Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add forgotten notifier unregister.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Originally, I expected that there would be needed to call update
operation in case RALUE record action is changed. However, that is not
needed since write operation takes care of that nicely. Remove prepared
construct and always call the write operation.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mlxsw we squash tables 254 and 255 together into HW. Kernel adds/dels
/32 ip to/from both 254 and 255. On del path, that causes the same
prefix being removed twice. Fix this by introducing reference counting
for private mlxsw fib entries. That required a bit of code reshuffle.
Also put dev into fib entry key so the same prefix could be represented
once per every router interface.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: dcbx fix series.

The series contains several small fixes for qed* dcbx module.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
   enable bits. Without this, the un-touched values will be merged with
   requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported a double free on kcm socket, which could
be easily reproduced by:

	#include <unistd.h>
	#include <sys/syscall.h>

	int main()
	{
	  int fd = syscall(SYS_socket, 0x29ul, 0x5ul, 0x0ul, 0, 0, 0);
	  syscall(SYS_ioctl, fd, 0x89e2ul, 0x20a98000ul, 0, 0, 0);
	  return 0;
	}

This is because on the error path, after we install
the new socket file, we call sock_release() to clean
up the socket, which leaves the fd pointing to a freed
socket. Fix this by calling sys_close() on that fd
directly.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Wang says:

====================
net: ethernet: mediatek: a couple of fixes

a couple of fixes come out from integrating with linux-4.8 rc1
they all are verified and workable on linux-4.8 rc1

Changes since v1:
- usage of loops to work out if all required clock are ready instead
of tedious coding
- remove redundant pinctrl setup that is already done by core driver
thanks for careful and patient reviewing by Andrew Lunn
- splitting distinct changes into the separate patches
- change variable naming from err to ret for readable coding

Changes since v2:
- restore to original clock disabling sequence that is changed
accidentally in the last version
- refine the commit log that would cause misunderstanding what has
been done in the changes
- refine the commit log that would cause footnote losing due to
improper delimiter use

Changes since v3:
- fix git rejects caused by mixing a change from net-next, so
remake the patch set based on the current net branch again.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.

Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.

Ref:
[1] https://patchwork.ozlabs.org/patch/344093/Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the missing of_node_put() after finishing the usage
of of_get_child_by_name.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mtk_stop() must be called to stop for freeing DMA
resources acquired and restoring state changed by mtk_open()
firstly when module removal.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

original mdio_cleanup is not in the symmetric place against where
mdio_init is, so relocate mdio_cleanup to the right one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

use skb_free_frag() instead of legacy put_page()
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of  SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit bc8c20ac ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.

Fixes: bc8c20ac ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Allow nf_tables reject expression from input, forward and output hooks,
   since only there the routing information is available, otherwise we crash.

2) Fix unsafe list iteration when flushing timeout and accouting objects.

3) Fix refcount leak on timeout policy parsing failure.

4) Unlink timeout object for unconfirmed conntracks too

5) Missing validation of pkttype mangling from bridge family.

6) Fix refcount leak on ebtables on second lookup for the specific
   bridge match extension, this patch from Sabrina Dubroca.

7) Remove unnecessary ip_hdr() in nf_tables_netdev family.

Patches from 1-5 and 7 from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three little fixes:
 * revert a recent wext patch, which Ben Hutchings noticed was
   wrong, and it turns out not to be necessary for any driver

 * fix an infinite loop that can occur under certain conditions
   in mac80211's TDLS code (depending on regulatory information)

 * add a cfg80211_get_station() static inline when cfg80211 isn't
   built, to allow other modules to not have to depend on it for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We have already use skb_header_pointer to get the ip header pointer,
so there's no need to use ip_hdr again. Moreover, in NETDEV INGRESS
hook, ip header maybe not linear, so use ip_hdr is not appropriate,
remove it.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This allows modules using this function (currently: batman-adv) to
compile even if cfg80211 is not built at all, thus relaxing
dependencies.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Stop downgrading TDLS chandef when reaching the AP BW. The AP provides
the necessary regulatory protection in this case.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=153961, which
reported an infinite loop here.
Reported-by: Kamil Toman <kamil.toman@gmail.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'hwmon-for-linus-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Add missing sysfs attribute group terminator to it87 driver"

* tag 'hwmon-for-linus-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (it87) Add missing sysfs attribute group terminator

Pull ext4 fixes from Ted Ts'o:
 "Fix bugs that could cause kernel deadlocks or file system corruption
  while moving xattrs to expand the extended inode.

  Also add some sanity checks to the block group descriptors to make
  sure we don't end up overwriting the superblock"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: avoid deadlock when expanding inode size
  ext4: properly align shifted xattrs when expanding inodes
  ext4: fix xattr shifting when expanding inodes part 2
  ext4: fix xattr shifting when expanding inodes
  ext4: validate that metadata blocks do not overlap superblock
  ext4: reserve xattr index for the Hurd

Pull networking fixes from David Miller:

 1) Segregate namespaces properly in conntrack dumps, from Liping Zhang.

 2) tcp listener refcount fix in netfilter tproxy, from Eric Dumazet.

 3) Fix timeouts in qed driver due to xmit_more, from Yuval Mintz.

 4) Fix use-after-free in tcp_xmit_retransmit_queue().

 5) Userspace header fixups (use of __u32, missing includes, etc.) from
    Mikko Rapeli.

 6) Further refinements to fragmentation wrt gso and tunnels, from
    Shmulik Ladkani.

 7) Trigger poll correctly for zero length UDP packets, from Eric
    Dumazet.

 8) TCP window scaling fix, also from Eric Dumazet.

 9) SLAB_DESTROY_BY_RCU is not relevant any more for UDP sockets.

10) Module refcount leak in qdisc_create_dflt(), from Eric Dumazet.

11) Fix deadlock in cp_rx_poll() of 8139cp driver, from Gao Feng.

12) Memory leak in rhashtable's alloc_bucket_locks(), from Eric Dumazet.

13) Add new device ID to alx driver, from Owen Lin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
  Add Killer E2500 device ID in alx driver.
  net: smc91x: fix SMC accesses
  Documentation: networking: dsa: Remove platform device TODO
  net/mlx5: Increase number of ethtool steering priorities
  net/mlx5: Add error prints when validate ETS failed
  net/mlx5e: Fix memory leak if refreshing TIRs fails
  net/mlx5e: Add ethtool counter for TX xmit_more
  net/mlx5e: Fix ethtool -g/G rx ring parameter report with striding RQ
  net/mlx5e: Don't wait for SQ completions on close
  net/mlx5e: Don't post fragmented MPWQE when RQ is disabled
  net/mlx5e: Don't wait for RQ completions on close
  net/mlx5e: Limit UMR length to the device's limitation
  rhashtable: fix a memory leak in alloc_bucket_locks()
  sfc: fix potential stack corruption from running past stat bitmask
  team: loadbalance: push lacpdus to exact delivery
  net: hns: dereference ppe_cb->ppe_common_cb if it is non-null
  8139cp: Fix one possible deadloop in cp_rx_poll
  i40e: Change some init flow for the client
  Revert "phy: IRQ cannot be shared"
  net: dsa: bcm_sf2: Fix race condition while unmasking interrupts
  ...

Merge tag 'platform-drivers-x86-v4.8-4' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver fixes from Darren Hart:
 "Remove module related code from two drivers that are only configurable
  as built-in: intel_pmic_gpio and platform/olpc"

* tag 'platform-drivers-x86-v4.8-4' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  intel_pmic_gpio: Make explicitly non-modular
  platform/olpc: Make ec explicitly non-modular

Pull powerpc fixes from Ben Herrenschmidt:
 "This was meant to be sent early last week, but I has a change pending
  on one of the fixes and other things made me forget all about.  Ugh.

  We have some misc fixes for powerpc 4.8.  Some trivial bits and some
  regressions, and a trivial cleanup or two that I saw no point in
  letting rot in patchwork"

* tag 'powerpc-4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: signals: Discard transaction state from signal frames
  powerpc/powernv : Drop reference added by kset_find_obj()
  powerpc/tm: do not use r13 for tabort_syscall
  powerpc: move hmi.c to arch/powerpc/kvm/
  powerpc: sysdev: cpm: fix gpio save_regs functions
  powerpc/pseries: PACA save area fix for MCE vs MCE
  powerpc/pseries: PACA save area fix for general exception vs MCE
  powerpc/prom: Fix sub-processor option passed to ibm, client-architecture-support
  powerpc, hotplug: Avoid to touch non-existent cpumasks.
  powerpc: migrate exception table users off module.h and onto extable.h
  powerpc/powernv/pci: fix iterator signedness
  powerpc/pseries: use pci_host_bridge.release_fn() to kfree(phb)
  cxl: use pcibios_free_controller_deferred() when removing vPHBs
  powerpc: mpc8349emitx: Delete unnecessary assignment for the field "owner"
  powerpc/512x: Delete unnecessary assignment for the field "owner"
  drivers/macintosh: Delete owner assignment
  powerpc: cputhreads: Add missing include file

Attribute array it87_attributes_in lacks its NULL terminator,
causing random behavior when operating on the attribute group.

Fixes: 52929715 ("hwmon: (it87) Use is_visible for voltage sensors")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The Kconfig entry controlling compilation of this code is:

drivers/platform/x86/Kconfig:config GPIO_INTEL_PMIC
drivers/platform/x86/Kconfig:   bool "Intel PMIC GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Alek Du <alek.du@intel.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

The Kconfig entry controlling compilation of this code is:

arch/x86/Kconfig:config OLPC
arch/x86/Kconfig:       bool "One Laptop Per Child support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b70661c7 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes.  Firstly,
the access size must correspond to the following rule:

(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
    the above.

Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.

Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation.  If neither, BUG().  This
exactly reflects the driver behaviour prior to the commit being fixed.

Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.

This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.

Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.

Fixes: b70661c7 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 83c0afae ("net: dsa: Add new binding implementation"),
the shortcomings of the dsa platform device have been addressed, remove
that TODO item.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes 2016-08-29

This series contains some bug fixes for the mlx5 core and mlx5
ethernet driver.

From Saeed, Fix UMR to consider hardware translation table field
size limitation when calculating the maximum number of MTTs required
by the driver.  Three patches to speed-up netdevice close time by
serializing channel (SQs & RQs) destruction rather than issuing and
waiting for hardware interrupts to free them.

From Eran, Fix ethtool ring parameter reporting for striding RQ layout.
Add error prints on ETS validation failure.

From Kamal, Fix memory leak on error flow.

From Maor, Fix ethtool steering priorities number.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>