When sending the sleep command for host drivers supporting
MMC_CAP_WAIT_WHILE_BUSY, we need to confirm that max_busy_timeout is
big enough comparing to the sleep timeout specified from card's
EXT_CSD. If this isn't case, we use a R1 response instead of R1B and
fallback to use a delay instead.

Do note that a max_busy_timeout set to zero by the host, is interpreted
as it can cope with whatever timeout the mmc core provides it with.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Conform to the eMMC spec and use the CMD6 generic timeout from the
EXT_CSD register, when switching to HS200 mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.

Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.

For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.

In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.

Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.

For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.

This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.

Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Put myself as a (co)maintainer of the mmc subsystem to help out Chris
Ball in a more official role.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Add support for non-blocking request, pre_req() runs dma_map_sg() and
post_req() runs dma_unmap_sg(). This patch can increase card read/write
speed, especially for high speed card and slow CPU(for some embedded
platform).

Users can get a great benefit from this patch. if CPU frequency is 800MHz,
SDR104 or DDR50 card read/write speed may increase more than 15%.

test results:
intel i3(800MHz - 2.3GHz), SD card clock 208MHz

performance mode(2.3GHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.18191 s, 56.8 MB/s
After:
 dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.09276 s, 61.4 MB/s

powersave mode(800MHz):
Before:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.29569 s, 51.8 MB/s
After:
dd if=/dev/mmcblk0p1 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 1.11218 s, 60.3 MB/s
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

The new phase searching method is more concise and easier to
understand.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

If the host driver removed while card in the slot, the host will not
power off card power correctly. This bug is produced because host
eject flag set before the last mmc_set_ios callback, we should set the
eject flag after power off.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>

This patch adds the erase capability to OMAP1/OMAP2420 MMC driver. Idea is
the same than in commit 93caf8e ("omap_hsmmc: add erase capability") that we
disable the data timeout interrupt for erases.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

Because use_dma is set only in mmc_omap_probe and unset nowhere there is no
need to carry that flag in struct mmc_omap_host for mmc_omap_prepare_data
function.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

Simplify probe and cleanup code by using devm_ioremap_resource. This also
makes probe code to follow more common allocate private struct followed by
other initialization style.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

Field mem_res in struct mmc_omap_host is used only once in mmc_omap_probe
when setting the phys_base field so we may just se the phys_base straight
and remove needless mem_res.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

host-irq is set twice so remove needless one.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

Omap MMC driver initialization can cause a NULL pointer dereference in
tasklet_hi_action on Nokia N810 if its miniSD cover is open during driver
initialization.

[    1.070000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[    1.080000] pgd = c0004000
[    1.080000] [00000000] *pgd=00000000
[    1.080000] Internal error: Oops: 80000005 [#1] PREEMPT ARM
[    1.080000] Modules linked in:
[    1.080000] CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 3.13.0-rc2+ #95
[    1.080000] Workqueue: events menelaus_work
[    1.080000] task: c7863340 ti: c7878000 task.ti: c7878000
[    1.080000] PC is at 0x0
[    1.080000] LR is at tasklet_hi_action+0x68/0xa4
...
[    1.080000] [<c003543c>] (tasklet_hi_action+0x68/0xa4) from [<c0034dd0>] (__do_softirq+0xbc/0x208)
[    1.080000] [<c0034dd0>] (__do_softirq+0xbc/0x208) from [<c003521c>] (irq_exit+0x84/0xac)
[    1.080000] [<c003521c>] (irq_exit+0x84/0xac) from [<c00135cc>] (handle_IRQ+0x64/0x84)
[    1.080000] [<c00135cc>] (handle_IRQ+0x64/0x84) from [<c000859c>] (omap2_intc_handle_irq+0x54/0x68)
[    1.080000] [<c000859c>] (omap2_intc_handle_irq+0x54/0x68) from [<c0015be0>] (__irq_svc+0x40/0x74)
[    1.080000] Exception stack(0xc7879d70 to 0xc7879db8)
[    1.080000] 9d60:                                     000003f1 0000000a 00000009 0000001c
[    1.080000] 9d80: c7879e70 c780bc10 c780bc10 00000000 00000001 00008603 c780bc78 c7879e4e
[    1.080000] 9da0: 00000002 c7879db8 c00343b0 c0160c9c 20000113 ffffffff
[    1.080000] [<c0015be0>] (__irq_svc+0x40/0x74) from [<c0160c9c>] (__aeabi_uidiv+0x20/0x9c)
[    1.080000] [<c0160c9c>] (__aeabi_uidiv+0x20/0x9c) from [<c00343b0>] (msecs_to_jiffies+0x18/0x24)
[    1.080000] [<c00343b0>] (msecs_to_jiffies+0x18/0x24) from [<c01ec3ec>] (omap_i2c_xfer+0x30c/0x458)
[    1.080000] [<c01ec3ec>] (omap_i2c_xfer+0x30c/0x458) from [<c01e9724>] (__i2c_transfer+0x3c/0x74)
[    1.080000] [<c01e9724>] (__i2c_transfer+0x3c/0x74) from [<c01eac4c>] (i2c_transfer+0x78/0x94)
[    1.080000] [<c01eac4c>] (i2c_transfer+0x78/0x94) from [<c01eb0bc>] (i2c_smbus_xfer+0x3c0/0x4f8)
[    1.080000] [<c01eb0bc>] (i2c_smbus_xfer+0x3c0/0x4f8) from [<c01eb414>] (i2c_smbus_write_byte_data+0x34/0x3c)
[    1.080000] [<c01eb414>] (i2c_smbus_write_byte_data+0x34/0x3c) from [<c01bb308>] (menelaus_write_reg+0x1c/0x40)
[    1.080000] [<c01bb308>] (menelaus_write_reg+0x1c/0x40) from [<c01bb904>] (menelaus_work+0xa0/0xc4)
[    1.080000] [<c01bb904>] (menelaus_work+0xa0/0xc4) from [<c00439c4>] (process_one_work+0x1fc/0x334)
[    1.080000] [<c00439c4>] (process_one_work+0x1fc/0x334) from [<c0043d6c>] (worker_thread+0x244/0x380)
[    1.080000] [<c0043d6c>] (worker_thread+0x244/0x380) from [<c0049d04>] (kthread+0xc0/0xd4)
[    1.080000] [<c0049d04>] (kthread+0xc0/0xd4) from [<c0012758>] (ret_from_fork+0x14/0x3c)
[    1.080000] Code: bad PC value
[    1.090000] ---[ end trace 7bc2fc7cd14f1d95 ]---
[    1.100000] Kernel panic - not syncing: Fatal exception in interrupt

Reason for this is that omap_notify_cover_event which calls
tasklet_hi_schedule gets called before struct cover_tasklet is initialized.

Call to omap_notify_cover_event on Nokia N810 happens from menelaus.c PMIC
driver via board-n8x0.c during execution of mmc_add_host in case of open
miniSD cover.

Fix this by moving cover_timer and cover_tasklet initialization before
mmc_add_host call in mmc_omap_new_slot.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Chris Ball <chris@printf.net>

This patch adds DT support for r8a7791.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>

This patch updates r8a7790 DT data to have SoC specific settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>

This patch updates r8a7779 DT data to have SoC specific settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>

This patch updates r8a7778 DT data to have SoC specific settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>

It is easier to read if sh_mobile_sdhi_of_cfg and
sh_mobile_sdhi_of_match are closer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>

There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.

To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>

There are no active users of this host capability. The primary reason
for adding this cap was due to a bug in ux500 boot loader code, which
is not a relevant issue any more. So, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead
we just make the feature default available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several
validations of a present bus_ops callback became redundant. Let's
remove these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.

To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.

By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Since the users of the exported PM functions are now using the modern
PM ops macros, we can convert to the proper corresponding PM configs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <chris@printf.net>

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <chris@printf.net>

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <chris@printf.net>

Pull SELinux fixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  SELinux:  Fix kernel BUG on empty security contexts.
  selinux: add SOCK_DIAG_BY_FAMILY to the list of netlink message types

Pull vfs fixes from Al Viro:
 "A couple of fixes, both -stable fodder.  The O_SYNC bug is fairly
  old..."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix a kmap leak in virtio_console
  fix O_SYNC|O_APPEND syncing the wrong range on write()