- 26 May, 2009 3 commits
-
-
Daniel Mack authored
This adds support for the SMSC911x chip found on the lilly-1131 module. Signed-off-by:
Daniel Mack <daniel@caiaq.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Daniel Mack authored
Support code for lilly-1131 is implemented in a module/baseboard fashion. All code specific to peripherals found on the development board will go to this file. Signed-off-by:
-
Daniel Mack authored
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based modules. The module needs a baseboard support to work which will be added in the next patch. Signed-off-by:
-
- 20 May, 2009 1 commit
-
-
Eric Lammerts authored
Signed-off-by:
Eric Lammerts <eric@lammerts.org> Signed-off-by:
-
- 19 May, 2009 2 commits
-
-
Magnus Lilja authored
Signed-off-by:
Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by:
-
Alberto Panizzo authored
Signed-off-by:
Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by:
-
- 18 May, 2009 1 commit
-
-
Magnus Lilja authored
The i.MX31 PDK consists of several boards, one of them is a debug board containing a CPLD which controls some debug leds, switch buttons, an interrupt chip and an Ethernet controller. This patch adds support for detecting if the PDK board is present (during boot) and adds the interrupt chip to the kernel. Signed-off-by:
-
- 17 May, 2009 1 commit
-
-
Sascha Hauer authored
Without this patch we end up with a log message like "mx3_sdc_fb mx3_sdc_fb: mx3fb: fb registered". That's two fb too much for my taste. Signed-off-by:
-
- 16 May, 2009 3 commits
-
-
Magnus Lilja authored
Restructure UART pin setup in preparation for adding other pins in later patches. Signed-off-by:
-
Alberto Panizzo authored
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001 From: Alberto Panizzo <maramaopercheseimorto@gmail.com> Date: Fri, 15 May 2009 17:21:21 +0200 Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
- 13 May, 2009 1 commit
-
-
Guennadi Liakhovetski authored
mx3fb.c calls disable_irq() from a DMA callback, i.e., in an IRQ-handler context, which has always been unsafe, and became deadly after the merge of threaded interrupt handler support. Use disable_irq_nosync() instead. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
- 07 May, 2009 28 commits
-
-
Valentin Longchamp authored
Signed-off-by:
Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by:
-
Valentin Longchamp authored
This adds the camera device based on Guennadi's soc_camera architecture for the mx31. The proposed init by Guennadi was removed and must be implemented in the board init file as it contains a lot of board specific info (memory size, clock speed). Signed-off-by:
-
Valentin Longchamp authored
This is used on all board of our system, so again this is done in the mx31moboard.c file. changes since v2: call to gpio_request added in platform code, and moved device initialization in baseboard files. changes since v1: pins are claimed in another patch Signed-off-by:
-
Sascha Hauer authored
In order to use the gpiolib, we now have to call gpio_request in the plaform code since it is not done in iomux code anymore. Signed-off-by: -
Valentin Longchamp authored
Since iomux code is not directly related to gpio on mx31, the calls to gpio_request are removed from iomux.c file. These calls have to be done in platform initialization files. The name of the singe pin call for iomux is also changed to mxc_iomux_alloc_pin. Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
header is part of the kernel now. Signed-off-by: -
Guennadi Liakhovetski authored
Add OTG device definition and resources to i.MX31 and a pure USB device mode support to the pcm037 board. Signed-off-by:
Guennadi Liakhovetski <lg@denx.de> Signed-off-by:
-
Sascha Hauer authored
Signed-off-by: -
Sascha Hauer authored
Also, remove usage of set_irq_type after request_irq. Signed-off-by: -
Vladimir Barinov authored
Add SDHC support for MX27ADS board Signed-off-by:
Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by:
-
Vladimir Barinov authored
Add 1-wire support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add Sharp-QVGA panel support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add I2C support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Add NAND support for MX27ADS board Signed-off-by:
-
Vladimir Barinov authored
Setup all pins at once in one table Signed-off-by:
-
Magnus Lilja authored
This patch adds the SMSC platform device to the Litekit board. Signed-off-by:
-
Magnus Lilja authored
Several comments in board config files stated "mandatory for CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL. Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
Magnus Lilja authored
Signed-off-by:
-
Valentin Longchamp authored
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and devboard mx31moboard baseboards. sdhc2 is present on both, but is not directly included in the mx31moboard file because a third baseboard (not supported yet) without sdhc2 is planned. Changes since v1: removed pin initialization from init/exit function and taken different comments into account Changes since v2: pin initialiation now is done in another patch for all current mx31moboard pins Signed-off-by:
-
Valentin Longchamp authored
Changes since v1: all the pins needed for the drivers are claimed in another patch Signed-off-by:
-
Valentin Longchamp authored
As suggested by Sascha, here we setup all the pins that we are using in the current (and currently reviewed) drivers for mx31moboard system. changes since v1: changed I2C1 pin names Signed-off-by:
-
Valentin Longchamp authored
As suggested by Sascha, I regroup them in a single patch so that the other patches become more orthogonal. changes since v1: changed I2C1 pin names Signed-off-by:
-
