Skip to content

L
linux
Switch branch/tag
  1. 07 Aug, 2007 6 commits
  3. 05 Aug, 2007 2 commits
  5. 04 Aug, 2007 11 commits
    • Salyzyn, Mark's avatar
      [SCSI] aacraid: prevent panic on adapter resource failure · 2b053729
      Salyzyn, Mark authored 
      If the driver fails to allocate the contiguous (DMAable) memory for
system reasons, we fail to load the instance, but then we try to free
the <nul> allocation in the cleanup code and we get a panic in
pci_free_consistent(). This is reported against an older kernel, hope
this is relevant for latest/greatest.
Signed-off-by: default avatarMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      2b053729
    • Boaz Harrosh's avatar
      [SCSI] aha152x: use data accessors and !use_sg cleanup · 2338545a
      Boaz Harrosh authored 
      And finally this is the regular !use_sg cleanup
and use of data accessors.
Signed-off-by: default avatarBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      2338545a
    • Boaz Harrosh's avatar
      [SCSI] aha152x: Fix check_condition code-path · 45333ffa
      Boaz Harrosh authored 
      check_condition code-path was similar but more
complicated to Reset. It went like this:

  1. extra space was allocated at aha152x_scdata for mirroring
    scsi_cmnd members.
  2. At aha152x_internal_queue() every not check_condition
    (REQUEST_SENSE) command was copied to above members in
    case of error.
  3. At busfree_run() in the DONE_CS phase if a Status of
    SAM_STAT_CHECK_CONDITION was detected. The command was
    re-queued Internally using aha152x_internal_queue(,,check_condition,)
    The old command members are over written with the
    REQUEST_SENSE info.
  4. At busfree_run() in the DONE_CS phase again. If it is a
    check_condition command, info was restored from mirror
    made at first call to aha152x_internal_queue() (see 2)
    and the command is completed.

What I did is:

  1. Allocate less space in aha152x_scdata only for the 16-byte
    original command. (which is actually not needed by scsi-ml
    anymore at this stage. But this is to much knowledge of scsi-ml)
  2. If Status == SAM_STAT_CHECK_CONDITION, then like before
     re-queue a REQUEST_SENSE command. But only now save original
     command members. (Less of them)
  3. In aha152x_internal_queue(), just like for Reset, use the
    check_condition hint to set differently the working members.
    execute the command.
  4. At busfree_run() in the DONE_CS phase again. restore needed
     members.

While at it. This patch fixes a BUG. Old code when sending
a REQUEST_SENSE for a failed command. Would than return with
cmd->resid == 0 which was the status of the REQUEST_SENSE.
The failing command resid was lost. And when would resid
be interesting if not on a failing command?
Signed-off-by: default avatarBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      45333ffa
    • Boaz Harrosh's avatar
      [SCSI] aha152x: Clean Reset path · 66acdb03
      Boaz Harrosh authored 
      What Reset code was doing:  Save command's important/dangerous
Info on stack. NULL those members from scsi_cmnd.
Issue a Reset. wait for it to finish than restore members
and return.

What I do is save or NULL nothing. But use the "resetting"
hint in aha152x_internal_queue() to NULL out working members
and leave struct scsi_cmnd alone.

The indent here looks funny but it will change/drop in last
patch and it is clear this way what changed.
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      66acdb03
    • Boaz Harrosh's avatar
      [SCSI] aha152x: preliminary fixes and some comments · 0ceb4798
      Boaz Harrosh authored 
        hunk by hunk:
  - CHECK_CONDITION is what happens to cmnd->status >> 1
    or after status_byte() macro. But here it is used
    directly on status which means 0x1 which is an undefined
    bit in the standard. And is a status that will never
    return from a target.

  - in busfree_run at the DONE_SC phase we have 3 distinct
    operation:
	1-if(DONE_SC->SCp.phase & check_condition)
          The REQUEST_SENSE command return.
          - Restore original command
	  - Than continue to operation 3.
	2-if(DONE_SC->SCp.Status==SAM_STAT_CHECK_CONDITION)
          A regular command returned with a status.
	  - Internally re-Q a REQUEST_SENSE.
	  - Do not do operation 3.
	3-
	  - Complete the command and return it to scsi-ml
     So the 0x2 in both these operations (1,2) means the scsi
     check-condition status, hence SAM_STAT_CHECK_CONDITION

  - Here the code asks about !(DONE_SC->SCp.Status & not_issued)
    but "not_issued" is an enum belonging to the "phase" member
    and not to the Status returned from target. The reason this
    works is because not_issued==1 and Also CHECK_CONDITION==1
    (remember from hunk 1). So actually the code was asking
    !(DONE_SC->SCp.Status & CHECK_CONDITION). Which means
    "Has the status been read from target yet?"
    Staus is read at status_run(). "not_issued" is
    cleared in seldo_run() which is usually earlier than
    status_run().

  So this patch does nothing as far as assembly is concerned
  but it does let the reader understand what is going on.
Signed-off-by: default avatarBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      0ceb4798
    • Boaz Harrosh's avatar
      [SCSI] aha152x: use bounce buffer · b1ee0795
      Boaz Harrosh authored 
      Cause highmem buffers to be bounced to low memory until this
driver supports highmem addresses.  Otherwise it just oopses
on NULL buffer addresses.
Signed-off-by: default avatarRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: default avatarBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      b1ee0795
    • Boaz Harrosh's avatar
      [SCSI] aha152x: fix debug mode symbol conflict · 50535df3
      Boaz Harrosh authored 
      The symbol <debug_locks> conflicts with the rather global one in
include/linux/locks.h.
Signed-off-by: default avatarRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: default avatarBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      50535df3
    • James Bottomley's avatar
      [SCSI] sd: disentangle barriers in SCSI · 03a5743a
      James Bottomley authored 
      Our current implementation has a generic set of barrier functions that
go through the SCSI driver model.  Realistically, this is unnecessary,
because the only device that can use barriers (sd) can set the flush
functions up at probe or revalidate time.  This patch pulls the barrier
functions out of the mid layer and scsi driver model and relocates them
directly in sd.
Acked-by: default avatarTejun Heo <htejun@gmail.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
      03a5743a
    • Michael Chan's avatar
      [BNX2]: Fix suspend/resume problem. · 6caebb02
      Michael Chan authored 
      The device would not resume properly if it was shutdown before the system
was suspended.  In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.

We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.

Update version to 1.6.4.
Signed-off-by: default avatarMichael Chan <mchan@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      6caebb02
    • Michael Chan's avatar
      [TG3]: Fix suspend/resume problem. · 3e0c95fd
      Michael Chan authored 
      Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended.  In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.

We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: default avatarMichael Chan <mchan@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3e0c95fd
    • Linus Torvalds's avatar
      Linux 2.6.23-rc2 · d4ac2477
      Linus Torvalds authored
      d4ac2477
  7. 03 Aug, 2007 21 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7