This reverts commit a101ad94.

The mcp23s18 is configurable on clearing the interrupt on either reading
INTCAP or GPIO. Since driver reads INTCAP in IRQ and not the GPIO reg need
to set control byte for this mode.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fixes: 79a9becd ("gpiolib: export descriptor-based GPIO interface")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pca953x_gpio_set_multiple() divides by 4 to convert from longs to bytes,
which assumes a 32-bit platform, and is not correct on 64-bit platforms.
Use "sizeof(...)" instead to fix this.

Cc: stable@vger.kernel.org
Fixes: b4818afe ("gpio: pca953x: Add set_multiple to allow multiple bits to be set in one write.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The standby GPIO controller can be used as a interrupt controller.
Select GPIOLIB_IRQCHIP when compiling this driver. Otherwise we get
a compilation error:

drivers/gpio/gpio-xgene-sb.c: In function 'xgene_gpio_sb_probe':
drivers/gpio/gpio-xgene-sb.c:312:10: error: 'struct gpio_chip'
  has no member named 'irqdomain'
  priv->gc.irqdomain = priv->irq_domain;
          ^
scripts/Makefile.build:295: recipe for target
'drivers/gpio/gpio-xgene-sb.o' failed
make[2]: *** [drivers/gpio/gpio-xgene-sb.o] Error 1

Fixes: 1013fc41 "gpio: xgene: Enable X-Gene standby GPIO as interrupt controller"
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add binding for generic parallel-in/serial-out shift register devices
used as GPIO.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
[Clarified ngpios semantic]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The previous 'o' is in conflict and not very orderly assigned.
We want to select an ioctl() major that does not conflict with
the existining ones.

Add the new reserved major (0xB4) to Documentation/ioctl/ioctl-number.txt

Fixes: 3c702e99 ("gpio: add a userspace chardev ABI for GPIOs")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I screwed up while merging the immutable branch for TPS65912,
so fixing it unbroken again.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 3fab91ea.

GPIO chip structure already has "parent" field which is used for the
same purpose as "dev" field in gpio_bank structure - store pointer on
GPIO device.

Hence, drop duplicated "dev" field from gpio_bank structure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'ib-mfd-regulator-gpio-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into devel

Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.

gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;

Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.

Fixes: commit 42178e2a ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.

Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
  Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
  to determine number of gpio lins to increment by. This is set
  appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
  Tested with mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The altr,interrupt-trigger property is not used by the driver.
Instead, altr,interrupt-type is used by the driver and the driver
does not probe if this property is not specified. Therefore, it
is expected that there are no users of the -trigger property in
the wild and that this is a typo in the documentation for the
altera-pio controller. This patch fixes the typo.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.

Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The implementation of lp3943_gpio_request/lp3943_gpio_free test pin_used
for tracing the pin usage. However, gpiolib already checks FLAG_REQUESTED
flag for the same purpose. So remove the redundant implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace calls to devm_request_mem_region and devm_ioremap with a
direct call to devm_ioremap_resource instead and modify error
handling.

Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more
clear.

A simplified version of the Coccinelle semantic patch that is used to
make this change is as follows:
//<smpl>
@nm@
expression myname;
identifier i;
@@

struct platform_driver i = { .driver = { .name = myname } };

@@
expression dev,res,size,e1,e;
expression nm.myname;
@@

-if (!devm_request_mem_region(dev, res->start, size,
-                              \(res->name\|dev_name(dev)\|myname\)))
                               {
-   ...
-   return ...;
-}
... when != res->start = e1
e =
-devm_ioremap(dev,res->start,size);
+devm_ioremap_resource(dev,res);

if
-(e == NULL)
+(IS_ERR(e))
{
 ...
-return ...;
+return PTR_ERR(e);
}
//</smpl>

Further, updated error handling by hand as devm_ioremap_resource
gives appropriate error messages, so remove unnecessary error
messages.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The TS-4800 is an i.MX515 board. Its GPIO driver should only be compiled
for this CPU or for test builds.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The original code of gpiodev_add_to_list is not very clear which
lead to bugs or compiling warning, reference the following patches:
Bugs:
1.  Commit ef7c7553 ("gpiolib: improve overlap check of range of
    gpio").
2.  Commit 96098df1 ("gpiolib: fix chip order in gpio list")

Warning:
1.  Commit e28ecca6 ("gpio: fix warning about iterator").
of gpio").

There is a off-list discussion about how to improve it consequently.
This commit try to follow this by rewriting the whole functions.

Tested pass with my gpio mockup driver and test scripts[1].

[1] http://www.spinics.net/lists/linux-gpio/msg09598.htmlSuggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These fields are initialized by bgpio_init() with exactly the same settings
so remove the redundant code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I named the field representing the current user of GPIO line as
"label" but this is too vague and ambiguous. Before anyone gets
confused, rename it to "consumer" and indicate clearly in the
documentation that this is a string set by the user of the line.

Also clean up leftovers in the documentation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We started to assign the gpio_device as parent for the sysfs
but this changes the expected layout of sysfs. Restore the
previous behaviour.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The 'dev_id' parameter of the GPIO_LOOKUP{,_IDX} macros were removed by
commit ad824783 ("gpio: better lookup method for platform GPIOs").

Update the documentation to reflect that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver has .can_sleep flag set.
So the pisosr_gpio_get() can be called from contexts that can sleep.
Thus use the cansleep() variant in pisosr_gpio_refresh().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ret variable can contain error values and is compared with zero.
Its type must be signed.

The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Move the code checking valid gpio count to cover both DT and non-DT cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'devm_gpiochip' of https://github.com/ldewangan/linux-upstream into devm-gpiochip-add-data

gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ret variable can contain error values and is compared with zero.
Its type must be signed.

The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.

This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>