The debugfs functions don't stub themselves out quite so well as might
be desirable so provide functions which do do this stubbing.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Show the register ranges we have in each rbtree node in debugfs, plus
some statistics on how big each node is and the total number of nodes.
It may also be worth collecting data on the ranges of dirty registers
to see if there's much mileage in trying to coalesce writes on sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This allows caches to add custom debugfs files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If the new register value is identical to the original one then suppress
the write to the hardware in regmap_update_bits(), saving some I/O cost.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There should be no situation where it offers any advantage over rbtree
and there are no current users so remove the code for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

One of the reasons for using a cache is to have a software shadow of a register
which is writable but not readable. This allows us to do a read-modify-write
operation on such a register.

Currently regcache checks whether a register is readable when performing a
cached read and returns an error if it is not. Drop this check, since it will
prevent us from using the cache for registers where read-back is not possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

regcache currently only properly works with val bit sizes of 8 or 16, since
it will, when calculating the cache word size, round down. This causes the
cache storage to be too small to hold the full register value. Fix this by
rounding up instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for 10 bits register, 14 bits value type register
formating. This is for example used by the Analog Devices AD5380.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

For some register format types we do not provide a parse_val so we can not do a
hardware read. But a cached read is still possible, so try to read from the
cache first, before checking whether a hardware read is possible. Otherwise the
cache becomes pretty useless for these register types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The reg_defaults field usually points to a static per driver array, which should
not be modified. Make requirement this explicit by making reg_defaults const.
To allow this the regcache_init code needs some minor changes. Previoulsy the
reg_config was not available in regcache_init and regmap->reg_defaults was used
to pass the default register set to regcache_init. Now that the reg_config is
available we can work on it directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Move the initialization regcache related fields of the regmap struct to
regcache_init. This allows us to keep regmap and regcache code better
separated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Calling regcache_exit from regcache_lzo_init is first of all a layering
violation and secondly will cause double frees. regcache_exit will free buffers
allocated by the core, but the core will also free the same buffers when the
cacheops init callback returns an error. Thus we end up with a double free.
Fix this by not calling regcache_exit but only free those buffers which, have
been allocated in this function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Calling regcache_exit from regcache_rbtree_init is first of all a layering
violation and secondly will cause double frees. regcache_exit will free buffers
allocated by the core, but the core will also free the same buffers when the
cacheops init callback returns an error. Thus we end up with a double free.
Fix this by not calling regcache_exit but only free those buffers which, have
been allocated in this function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure all allocated memory gets freed again in case initializing the cache
failed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure reg_defaults_raw gets freed in case of an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The regmap_init documentation states that it will either return a pointer to a
valid regmap structure or a ERR_PTR in case of an error. Currently it returns a
NULL pointer in case no bus or no config was given. Since NULL is not a
ERR_PTR a caller might assume that it is a pointer to a valid regmap structure,
so return a ERR_PTR(-EINVAL) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If regcache initialization fails regmap_init will currently exit without
freeing work_buf.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Commit 10a08d9f ("regmap: Support some block operations on cached devices")
allowed raw read operations without throwing a warning when using caches if
all registers are volatile. This patch does the same for raw write operations.

This is for example useful when loading a firmware in a predefined volatile
region on a chip where we otherwise want registers to be cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We already have the same code for checking whether a register range is volatile
in two different places. Instead of duplicating it once more  add a small helper
function for checking whether a register range is voltaile.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Users probably don't care about the specific compression algorithm and
we might want to use a different algorithm (snappy being the one I'm
thinking of right now) so update the public interface to have a more
generic name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allow drivers to optimise out the register cache sync if they didn't need
to do one. If the hardware is desynced from the register cache (by power
loss for example) then the driver should call regcache_mark_dirty() to
let the core know about this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

80 columns FTW.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Give regcache_lzo_block_count() a copy of the map so that when we decide
we want to make the LZO cache more controllable we can more easily do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>

There seem to be lots of regmap-using devices with very similar interrupt
controllers with a small bank of interrupt registers and mask registers
with an interrupt per bit. This won't cover everything but it's a good
start.

Each chip supplies a base for the status registers, a base for the mask
registers, an optional base for writing acknowledgements (which may be the
same as the status registers) and an array of bits within each of these
register banks which indicate the interrupt.

There is an assumption that the bit for each interrupt will be the same
in each of the register bank.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

.. with new name.  Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (31 commits)
  ARM: OMAP: Fix export.h or module.h includes
  ARM: OMAP: omap_device: Include linux/export.h
  ARM: OMAP2: Fix H4 matrix keyboard warning
  ARM: OMAP1: Remove unused omap-alsa.h
  ARM: OMAP1: Fix warnings about enabling 32 KiHz timer
  ARM: OMAP2+: timer: Remove omap_device_pm_latency
  ARM: OMAP2+: clock data: Remove redundant timer clkdev
  ARM: OMAP: Devkit8000: Remove double omap_mux_init_gpio
  ARM: OMAP: usb: musb: OMAP: Delete unused function
  MAINTAINERS: Update linux-omap git repository
  ARM: OMAP: change get_context_loss_count ret value to int
  ARM: OMAP4: hsmmc: configure SDMMC1_DR0 properly
  ARM: OMAP4: hsmmc: Fix Pbias configuration on regulator OFF
  ARM: OMAP3: hwmod: fix variant registration and remove SmartReflex from common list
  ARM: OMAP: I2C: Fix omap_register_i2c_bus() return value on success
  ARM: OMAP: dmtimer: Include linux/module.h
  ARM: OMAP2+: l3-noc: Include linux/module.h
  ARM: OMAP2+: devices: Fixes for McPDM
  ARM: OMAP: Fix errors and warnings when building for one board
  ARM: OMAP3: PM: restrict erratum i443 handling to OMAP3430 only
  ...

Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.

Simple way to reproduce the problem in mainline:

    cat >/tmp/a.c <<'EOF'
    #include <unistd.h>
    #include <fcntl.h>
    #include <stdio.h>
    main()
    {
            struct flock fl = {.l_type = F_RDLCK, .l_whence = SEEK_SET, .l_len = 1};
            if (fcntl(0, F_SETLK, &fl))
                    perror("setlk");
    }
    EOF
    cc /tmp/a.c -o /tmp/test

then on nfs4:

    mount --bind file1 file2
    /tmp/test < file1		# ok
    /tmp/test < file2		# spews "setlk: No locks available"...

What happens is the missing call of ->d_revalidate() after mountpoint
crossing and that's where NFS4 would issue OPEN request to server.

The fix is simple - treat mountpoint crossing the same way we deal with
following procfs-style symlinks.  I.e.  set LOOKUP_JUMPED...

Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf top: Fix live annotation in the --stdio interface
  perf top tui: Don't recalc column widths considering just the first page
  perf report: Add progress bar when processing time ordered events
  perf hists browser: Warn about lost events
  perf tools: Fix a typo of command name as trace-cmd
  perf hists: Fix recalculation of total_period when sorting entries
  perf header: Fix build on old systems
  perf ui browser: Handle K_RESIZE in dialog windows
  perf ui browser: No need to switch char sets that often
  perf hists browser: Use K_TIMER
  perf ui: Rename ui__warning_paranoid to ui__error_paranoid
  perf ui: Reimplement the popup windows using libslang
  perf ui: Reimplement ui__popup_menu using ui__browser
  perf ui: Reimplement ui_helpline using libslang
  perf ui: Improve handling sigwinch a bit
  perf ui progress: Reimplement using slang
  perf evlist: Fix grouping of multiple events

Commit 32aaeffb (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:

$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
  grep -L linux/module.h
  arch/arm/mach-omap2/dsp.c
  arch/arm/mach-omap2/mailbox.c
  arch/arm/mach-omap2/omap-iommu.c
  arch/arm/mach-omap2/smartreflex.c

Also check we either have export.h or module.h included
for the files exporting symbols:

$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
  grep -L linux/export.h | xargs grep -L linux/module.h

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include linux/export.h to fix below build warning:

  CC      arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
  forcedeth: fix a few sparse warnings (variable shadowing)
  forcedeth: Improve stats counters
  forcedeth: remove unneeded stats updates
  forcedeth: Acknowledge only interrupts that are being processed
  forcedeth: fix race when unloading module
  MAINTAINERS/rds: update maintainer
  wanrouter: Remove kernel_lock annotations
  usbnet: fix oops in usbnet_start_xmit
  ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
  etherh: Add MAINTAINERS entry for etherh
  bonding: comparing a u8 with -1 is always false
  sky2: fix regression on Yukon Optima
  netlink: clarify attribute length check documentation
  netlink: validate NLA_MSECS length
  i825xx:xscale:8390:freescale: Fix Kconfig dependancies
  macvlan: receive multicast with local address
  tg3: Update version to 3.121
  tg3: Eliminate timer race with reset_task
  tg3: Schedule at most one tg3_reset_task run
  tg3: Obtain PCI function number from device
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rx byte count was off; instead use the hardware's count.  Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.

- The count of transmitted packets reported by the forcedeth driver
  reports pre-TSO (TCP Segmentation Offload) packet counts and not the
  count of the number of packets sent on the wire. This change fixes
  the forcedeth driver to report the correct count. Fixed the code by
  copying the count stored in the NIC H/W to the value reported by the
  driver.

- Count rx_drop_frame errors as rx_fifo_errors:
  We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
  for too long.  Normally, rx_fifo_errors would be counted in this case.
  The rx_drop_frame error count is private to forcedeth and is not
  reported by ifconfig or sysfs.  The rx_fifo_errors count is currently
  unused in the forcedeth driver.  It is reported by ifconfig as overruns.
  This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.

Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process.  This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().

Tested:
  x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
  + rmmod/modprobe/ifconfig in a loop

Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>