Based on original patch and description from Flavio Leitner <fbl@redhat.com>

When bnx2_reset_task() is called, it will stop,
(re)initialize and start the interface to restore
the working condition.

The bnx2_init_nic() calls bnx2_reset_nic() which will
reset the chip and then calls bnx2_free_skbs() to free
all the skbs.

The problem happens when bnx2_init_chip() fails because
bnx2_reset_nic() will just return skipping the ring
initializations at bnx2_init_all_rings(). Later, the
reset task starts the interface again and the system
crashes due a NULL pointer access (no skb in the ring).

To fix it, we call dev_close() if bnx2_init_nic() fails.
One minor wrinkle to deal with is the cancel_work_sync()
call in bnx2_close() to cancel bnx2_reset_task().  The
call will wait forever because it is trying to cancel
itself and the workqueue will be stuck.

Since bnx2_reset_task() holds the rtnl_lock() and checks
for netif_running() before proceeding, there is no need
to cancel bnx2_reset_task() in bnx2_close() even if
bnx2_close() and bnx2_reset_task() are running concurrently.
The rtnl_lock() serializes the 2 calls.

We need to move the cancel_work_sync() call to
bnx2_remove_one() to make sure it is canceled before freeing
the netdev struct.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

The registers and descriptors bits are identical to the pre-8168
8169 chipsets : {RxDesc / TxDesc}.opts2 can only contain VLAN information.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove redundant variable "work".
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes obsolete code in the initialisation/creation of
slcan devices.

It follows the suggested cleanups from Ilya Matvejchikov in
drivers/net/slip.c that where recently applied to net-next-2.6:

- slip: remove dead code within the slip initialization
- slip: remove redundant check slip_devs for NULL
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5f77898d does not completely
fix the problem of handling allocations with irqs disabled..  The
below patch on top of it fixes the problem completely.

Based on review by "Ivan Vecera" <ivecera@redhat.com>..
"
Small note, the root of the problem was that non-atomic allocation was requested with IRQs disabled. Your patch description does not contain wwhy were the IRQs disabled.

The function bnad_mbox_irq_alloc incorrectly uses 'flags' var for two different things, 1) to save current CPU flags and 2) for request_irq
call.
First the spin_lock_irqsave disables the IRQs and saves _all_ CPU flags (including one that enables/disables interrupts) to 'flags'. Then the 'flags' is overwritten by 0 or 0x80 (IRQF_SHARED). Finally the spin_unlock_irqrestore should restore saved flags, but these flags are now either 0x00 or 0x80. The interrupt bit value in flags register on x86 arch is 0x100.
This means that the interrupt bit is zero (IRQs disabled) after spin_unlock_irqrestore so the request_irq function is called with disabled interrupts.
"
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
	net/bluetooth/l2cap_core.c

Fix the condition where PS3 network RX hangs when no network
TX is occurring by calling gelic_card_enable_rxdmac() during
RX_DMA_CHAIN_END event processing.

The gelic hardware automatically clears its RX_DMA_EN flag when
it detects an RX_DMA_CHAIN_END event.  In its processing of
RX_DMA_CHAIN_END the gelic driver is required to set RX_DMA_EN
(with a call to gelic_card_enable_rxdmac()) to restart RX DMA
transfers.  The existing gelic driver code does not set
RX_DMA_EN directly in its processing of the RX_DMA_CHAIN_END
event, but uses a flag variable card->rx_dma_restart_required
to schedule the setting of RX_DMA_EN until next inside the
interrupt handler.

It seems this delayed setting of RX_DMA_EN causes the hang since
the next RX interrupt after the RX_DMA_CHAIN_END event where
RX_DMA_EN is scheduled to be set will not occur since RX_DMA_EN
was not set.  In the case were network TX is occuring, RX_DMA_EN
is set in the next TX interrupt and RX processing continues.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Overview:
 Support mapping of priorities to traffic classes and
 traffic classes to transmission queues ranges in the net device.
 The queue ranges are (count, offset) pairs relating to the txq
 array.
 This can be done via DCBX negotiation or by kernel.
 As a result Enhanced Transmission Selection (ETS) and Priority Flow
 Control (PFC) are supported between L2 network traffic classes.

 Mapping:
 This patch uses the netdev_set_num_tc, netdev_set_prio_tc_map and
 netdev_set_tc_queue functions to map priorities to traffic classes
 and traffic classes to transmission queue ranges.
 This mapping is performed by bnx2x_setup_tc function which is
 connected to the ndo_setup_tc.
 This function is always called at nic load where by default it
 maps all priorities to tc 0, and it may also be called by the
 kernel or by the bnx2x upon DCBX negotiation to modify the mapping.

 rtnl lock:
 When the ndo_setup_tc is called at nic load or by kernel the rtnl
 lock is already taken. However, when DCBX negotiation takes place
 the lock is not taken. The work is therefore scheduled to be
 handled by the sp_rtnl task.

 Fastpath:
 The fastpath structure of the bnx2x which was previously used
 to hold the information of one tx queue and one rx queue was
 redesigned to represent multiple tx queues, one for each traffic
 class.
 The transmission queue supplied in the skb by the kernel can no
 longer be interpreted as a straightforward index into the fastpath
 structure array, but it must rather be decoded to the appropriate
 fastpath index and the tc within that fastpath.

 Slowpath:
 The bnx2x's queue object was redesigned to accommodate multiple
 transmission queues. The queue object's state machine was enhanced
 to allow opening multiple transmission-only connections on top of
 the regular tx-rx connection.

 Firmware:
 This feature relies on the tx-only queue feature introduced in the
 bnx2x 7.0.23 firmware and the FW likewise must have the bnx2x multi
 cos support.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Renaming the "reset_task" to a more general purpose name,
 "sp_rtnl_task", as it is already used for another purpose
 other than reset which is parity recovery, and since I
 plan to add a third operation for this task, updating the
 priority to traffic class and traffic class to transmission
 queues mappings after dcbx negotiation takes place.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove it, as it indirectly exposes netdev features. It's not used in
iproute2 (2.6.38) - is anything else using its interface?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same information and more can be obtained by using ethtool
with ETHTOOL_GFEATURES.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not used anywhere except net/core/dev.c now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan_features contains features inherited from underlying device.
NETIF_SOFT_FEATURES are not inherited but belong to the vlan device
itself (ensured in vlan_dev_fix_features()).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the fact that ORing with zero is a no-op.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove wrong setting of dev->flags. NETIF_F_NO_CSUM maps to IFF_DEBUG
there, so looks like a mistake.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.

For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Only 8111b needs to enable rx when shutdowning with WoL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Only 8111E needs enable RxConfig bit 0 ~ 3 when suspending or
shutdowning for wake on lan.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Add the ERI functions which would be used by the new chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

- Disable tx and rx by resetting hw, so replace rtl8169_asic_down
  with rtl8169_hw_reset.
- RxConfig bits 0 ~ 5 have to be cleared before hw reset to avoid
  receiving spurious data.
- Certain chips need to do some checking before reset.
- Remove hw reset which is done before hw_start. It is done in close,
  down or device probe functions.
- Move rtl8169_init_ring_indexes function into rtl_hw_reset function.
  The indexes of tx and rx only need to be zero when the hw resets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Define new registers and modify some existing ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Reset card->tx_dma_progress when lv1_net_start_tx_dma() fails or it
won't send anything afterwards anymore
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert to a proper state when gelic_card_kick_txdma() fails:
- Don't trigger BUG_ON when releasing the unsent tx descriptor
- Reset the tx chain head since the tail was not modified and
  hence not in sync
- Unlink the released descriptor bus address from its predecessor
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Change FW dump capture mask to a defult value, instead of using the recommended
  value from the FW. This was done to keep the capture mask consistent with other
  function drivers.

o Update driver version to 5.0.21
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Defined error code such as fw not responding, test already running and
  cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.

Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

to allow iSCSI connection to fail faster instead of waiting for the
long timeout.

Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data.  The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.

The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>