- 29 Jun, 2017 40 commits
-
-
Arvind Yadav authored
attribute_groups are not supposed to change at runtime. All functions working with attribute_groups provided by <linux/sysfs.h> work with const attribute_group. So mark the non-const structs as const. File size before: text data bss dec hex filename 2645 896 0 3541 dd5 net/bridge/br_sysfs_br.o File size After adding 'const': text data bss dec hex filename 2701 832 0 3533 dcd net/bridge/br_sysfs_br.o Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arvind Yadav authored
attribute_groups are not supposed to change at runtime. All functions working with attribute_groups provided by <linux/device.h> work with const attribute_group. So mark the non-const structs as const. File size before: text data bss dec hex filename 9968 3168 16 13152 3360 net/core/net-sysfs.o File size After adding 'const': text data bss dec hex filename 10160 2976 16 13152 3360 net/core/net-sysfs.o Signed-off-by:
-
Arvind Yadav authored
dev_pm_ops are not supposed to change at runtime. All functions working with dev_pm_ops provided by <linux/device.h> work with const dev_pm_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o File size After adding 'const': text data bss dec hex filename 19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o Signed-off-by:
-
Arvind Yadav authored
dev_pm_ops are not supposed to change at runtime. All functions working with dev_pm_ops provided by <linux/device.h> work with const dev_pm_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 18709 401 0 19110 4aa6 drivers/net/ethernet/smsc/smc91x.o File size After adding 'const': text data bss dec hex filename 18901 201 0 19102 4a9e drivers/net/ethernet/smsc/smc91x.o Signed-off-by:
-
Arvind Yadav authored
dev_pm_ops are not supposed to change at runtime. All functions working with dev_pm_ops provided by <linux/device.h> work with const dev_pm_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 15426 1256 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o File size After adding 'const': text data bss dec hex filename 15618 1064 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o Signed-off-by:
-
Thomas Falcon authored
The driver currently creates RX/TX queues during device probe, but assigns IRQ's to them during device open. On reset, however, IRQ's are assigned when resetting the queues. If there is a reset while the device is closed and the device is later opened, the driver will request IRQ's twice, causing the open to fail. This patch assigns the IRQ's in the ibmvnic_init function after the queues are reset or initialized, ensuring IRQ's are only requested once. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
-
Donald Sharp authored
Add to RTNL_FAMILY_IPMR, RTM_GETROUTE the ability to retrieve one S,G mroute from a specified table. *,G will return mroute information for just that particular mroute if it exists. This is because it is entirely possible to have more S's then can fit in one skb to return to the requesting process. Signed-off-by:
Donald Sharp <sharpd@cumulusnetworks.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Martin KaFai Lau authored
The index is off-by-one when fp->aux->stack_depth has already been rounded up to 32. In particular, if stack_depth is 512, the index will be 16. The fix is to round_up and then takes -1 instead of round_down. [ 22.318680] ================================================================== [ 22.319745] BUG: KASAN: global-out-of-bounds in bpf_prog_select_runtime+0x48a/0x670 [ 22.320737] Read of size 8 at addr ffffffff82aadae0 by task sockex3/1946 [ 22.321646] [ 22.321858] CPU: 1 PID: 1946 Comm: sockex3 Tainted: G W 4.12.0-rc6-01680-g2ee87db3 #22 [ 22.323061] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.el7.centos 04/01/2014 [ 22.324260] Call Trace: [ 22.324612] dump_stack+0x67/0x99 [ 22.325081] print_address_description+0x1e8/0x290 [ 22.325734] ? bpf_prog_select_runtime+0x48a/0x670 [ 22.326360] kasan_report+0x265/0x350 [ 22.326860] __asan_report_load8_noabort+0x19/0x20 [ 22.327484] bpf_prog_select_runtime+0x48a/0x670 [ 22.328109] bpf_prog_load+0x626/0xd40 [ 22.328637] ? __bpf_prog_charge+0xc0/0xc0 [ 22.329222] ? check_nnp_nosuid.isra.61+0x100/0x100 [ 22.329890] ? __might_fault+0xf6/0x1b0 [ 22.330446] ? lock_acquire+0x360/0x360 [ 22.331013] SyS_bpf+0x67c/0x24d0 [ 22.331491] ? trace_hardirqs_on+0xd/0x10 [ 22.332049] ? __getnstimeofday64+0xaf/0x1c0 [ 22.332635] ? bpf_prog_get+0x20/0x20 [ 22.333135] ? __audit_syscall_entry+0x300/0x600 [ 22.333770] ? syscall_trace_enter+0x540/0xdd0 [ 22.334339] ? exit_to_usermode_loop+0xe0/0xe0 [ 22.334950] ? do_syscall_64+0x48/0x410 [ 22.335446] ? bpf_prog_get+0x20/0x20 [ 22.335954] do_syscall_64+0x181/0x410 [ 22.336454] entry_SYSCALL64_slow_path+0x25/0x25 [ 22.337121] RIP: 0033:0x7f263fe81f19 [ 22.337618] RSP: 002b:00007ffd9a3440c8 EFLAGS: 00000202 ORIG_RAX: 0000000000000141 [ 22.338619] RAX: ffffffffffffffda RBX: 0000000000aac5fb RCX: 00007f263fe81f19 [ 22.339600] RDX: 0000000000000030 RSI: 00007ffd9a3440d0 RDI: 0000000000000005 [ 22.340470] RBP: 0000000000a9a1e0 R08: 0000000000a9a1e0 R09: 0000009d00000001 [ 22.341430] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000010000 [ 22.342411] R13: 0000000000a9a023 R14: 0000000000000001 R15: 0000000000000003 [ 22.343369] [ 22.343593] The buggy address belongs to the variable: [ 22.344241] interpreters+0x80/0x980 [ 22.344708] [ 22.344908] Memory state around the buggy address: [ 22.345556] ffffffff82aad980: 00 00 00 04 fa fa fa fa 04 fa fa fa fa fa fa fa [ 22.346449] ffffffff82aada00: 00 00 00 00 00 fa fa fa fa fa fa fa 00 00 00 00 [ 22.347361] >ffffffff82aada80: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa [ 22.348301] ^ [ 22.349142] ffffffff82aadb00: 00 01 fa fa fa fa fa fa 00 00 00 00 00 00 00 00 [ 22.350058] ffffffff82aadb80: 00 00 07 fa fa fa fa fa 00 00 05 fa fa fa fa fa [ 22.350984] ================================================================== Fixes: b870aa90 ("bpf: use different interpreter depending on required stack size") Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Acked-by:
Alexei Starovoitov <ast@fb.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in netdev_err message Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
David S. Miller authored
Michael Grzeschik says: ==================== arcnet: Collection of latest features Here we sum up the latest features to improve the arcnet framework. One patch is used to get feedback from the transfer queue about failed xfers by adding the err_skb message queue. Beside that we improve the backplane status that can be read by the PCI-based cards and offer that status via an extra sysfs attribute. In the last patch we add another card type PCIFB2. ==================== Signed-off-by: -
Michael Grzeschik authored
We add support for the PCIFB2 card from EAE. Beside other cards, this card has the backplane mode enabled by default. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
-
Michael Grzeschik authored
We read the backplane mode of each subcard from bits 2 and 3 of the misc register. Signed-off-by:
-
Michael Grzeschik authored
We add the sysfs interface the read back the backplane status of the interface. Signed-off-by:
-
Michael Grzeschik authored
We need to track the status of our queued packages. This way the driving process knows if failed packages need to be retransmitted. For this purpose we queue the transferred/failed packages back into the err_skb message queue added with some status information. Signed-off-by:
-
David S. Miller authored
Tom Lendacky says: ==================== amd-xgbe: AMD XGBE driver updates 2016-06-28 The following updates and fixes are included in this driver update series: - Simplify mailbox interface code - Fix SFP supported and advertising settings - Fix PTP initialization register usage - Insure there is timestamp skb present before using it - Add a timeout to timestamp register updates - Handle return code from software reset function - Some fixes for handling 2.5Gbps rates - Limit I2C error messages - Fix non-DMA interrupt handling through tasklet usage - Add NUMA affinity support for memory allocations - Add NUMA affinity support for interrupts - Prepare for more fine-grained cache coherency controls - Simplify setting the DMA burst length programming - Performance improvements This patch series is based on net-next. ==================== Signed-off-by: -
Lendacky, Thomas authored
Add support to change some general performance settings and to provide some performance settings based on the device that is probed. This includes: - Setting the maximum read/write outstanding request limit - Reducing the AXI interface burst length size - Selectively setting the Tx and Rx descriptor pre-fetch threshold - Selectively setting additional cache coherency controls Tested and verified on all versions of the hardware. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Lendacky, Thomas authored
Currently the driver hardcodes the PBLx8 setting. Remove the need for specifying the PBLx8 setting and automatically calculate based on the specified PBL value. Since the PBLx8 setting applies to both Tx and Rx use the same PBL value for both of them. Also, the driver currently uses a bit field to set the AXI master burst len setting. Change to the full bit field range and set the burst length based on the specified value. Signed-off-by:
-
Lendacky, Thomas authored
In prep for setting fine grained read and write DMA cache coherency controls, allow specific values to be used to set the cache coherency registers. Signed-off-by:
-
Lendacky, Thomas authored
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on the processors corresponding to the NUMA node of the device. Signed-off-by:
-
Lendacky, Thomas authored
Add support to perform memory allocations on the node of the device. The original allocation or the ring structure and Tx/Rx queues allocated all of the memory at once and then carved it up for each channel and queue. To best ensure that we get as much memory from the NUMA node as we can, break the channel and ring allocations into individual allocations. Signed-off-by:
-
Lendacky, Thomas authored
Some of the device interrupts should function as level interrupts. For some hardware configurations this requires setting some control bits so that if the interrupt status has not been cleared the interrupt should be reissued. Additionally, when using MSI or MSI-X interrupts, run the interrupt service routine as a tasklet so that the re-issuance of the interrupt is handled properly. Signed-off-by:
-
Lendacky, Thomas authored
When I2C communication fails, it tends to always fail. Rather than continuously issue an error message (once per second in most cases), change the message to be issued just once. Signed-off-by:
-
Lendacky, Thomas authored
The driver has some missing functionality when operating in the mode that supports 2.5GbE. Fix the driver to fully recognize and support this speed. Signed-off-by:
-
Lendacky, Thomas authored
Currently the function that performs a software reset of the hardware provides a return code. During driver probe check this return code and exit with an error if the software reset fails. Signed-off-by:
-
Lendacky, Thomas authored
Just to be on the safe side, should the update of the timestamp registers not complete, issue a warning rather than looping forever waiting for the update to complete. Signed-off-by:
-
Lendacky, Thomas authored
Spurious Tx timestamp interrupts can cause an oops in the Tx timestamp processing function if a Tx timestamp skb is NULL. Add a check to insure a Tx timestamp skb is present before attempting to use it. Signed-off-by:
-
Lendacky, Thomas authored
During PTP initialization, the Timestamp Control register should be cleared and not the Tx Configuration register. While this typo causes the wrong register to be cleared, the default value of each register and and the fact that the Tx Configuration register is programmed afterwards doesn't result in a bug, hence only fixing in net-next. Signed-off-by:
-
Lendacky, Thomas authored
When using SFPs, the supported and advertised settings should be initially based on the SFP that has been detected. The code currently indicates the overall support of the device as opposed to what the SFP is capable of. Update the code to change the supported link modes, auto-negotiation, etc. to be based on the installed SFP. Signed-off-by:
-
Lendacky, Thomas authored
Simplify and centralize the mailbox command rate change interface by having a single function perform the writes to the mailbox registers to issue the request. Signed-off-by:
-
David S. Miller authored
Martin KaFai Lau says: ==================== bpf: Add syscall lookup support for fd array and htab This patchset adds BPF_MAP_LOOKUP_ELEM syscall support for BPF_MAP_TYPE_PROG_ARRAY, BPF_MAP_TYPE_ARRAY_OF_MAPS and BPF_MAP_TYPE_HASH_OF_MAPS ==================== Reviewed-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Martin KaFai Lau authored
Checks are added to the existing sockex3 and test_map_in_map test. Signed-off-by:
-
Martin KaFai Lau authored
This patch allows userspace to do BPF_MAP_LOOKUP_ELEM on BPF_MAP_TYPE_PROG_ARRAY, BPF_MAP_TYPE_ARRAY_OF_MAPS and BPF_MAP_TYPE_HASH_OF_MAPS. The lookup returns a prog-id or map-id to the userspace. The userspace can then use the BPF_PROG_GET_FD_BY_ID or BPF_MAP_GET_FD_BY_ID to get a fd. Signed-off-by:
-
Thor Thayer authored
Version 3.70a of the Designware has additional DMA registers so add those to the ethtool DMA Register dump. Offset 9 - Receive Interrupt Watchdog Timer Register Offset 10 - AXI Bus Mode Register Offset 11 - AHB or AXI Status Register Offset 22 - HW Feature Register Signed-off-by:
Thor Thayer <thor.thayer@linux.intel.com> Acked-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2017-06-27 (Innova IPsec offload support) This patchset adds support for Innova IPSec network interface card. About Innova device: -------------------- Innova is a network card with a ConnectX chip and an FPGA chip as a bump-on-the-wire. Internal +----------+ Link +-----------------+ | +--------------+ FPGA | +------+ | ConnectX | | Shell +--+ QSFP | | +--------------+ +-------+ | | Port | +----------+ I2C | | SBU | | +------+ | +-------+ | +--+----------+---+ | | +--+--+ +---+---+ | DDR | | Flash | +-----+ +-------+ The FPGA synthesized logic is loaded from dedicated flash storage and has access to its own dedicated DDR RAM. The ConnectX chip firmware programs the FPGA by accessing its configuration space over either the slow internal I2C link or the high-speed internal link. The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU). mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality, while other components may handle the various SBU functionalities. The driver opens high-speed reliable communication channels with the shell and the SBU over the internal link. These channels may be used for high-bandwidth configuration or for SBU-specific out-of-band data paths. About Innova IPSec device: -------------------------- Innova IPSec is a network card that allows offloading IPSec cryptography operations from the host CPU to the NIC. It is an Innova card with an IPSec SBU. The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's DDR memory. Internal +----------+ Link +-----------------+ | +--------------+ FPGA | +------+ | ConnectX | | Shell +--+ QSFP | | +--------------+ +-------+ | | Port | +----------+ Internal I2C | | IPSec | | +------+ | | SBU | | | +-------+ | +--+----------+---+ | | +--+--+ +---+---+ | DDR | | | | | | Flash | |SADB | | | +-----+ +-------+ Modes and ciphers: Currently the following modes and ciphers are supported: IPv4 and IPv6 ESP tunnel and transport modes AES 128 and 256 bit encryption, with GCM authentication (RFC4106) IV is generated using seqiv, in sync with Linux's geniv. More modes and ciphers may be added later. Notes: In the future similar functionality will be included in a single-chip NIC. About the driver: ----------------- Patches 1-4 prepare some existing driver code for the new feature: * Add support for reserved GIDs in the hardware GID table * Allow multiple modules to enable hardware RoCE support independently Patches 5-6 define structs and helper functions for QP work-queues. Patches 7-11 add various FPGA-related features required for Innova. IPSec. Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices. atches 13-16 add IPSec offload support to the mlx5 netdevice. This driver services the new IPSec offload API introduced in commit d77e38e6 ("xfrm: Add an IPsec hardware offloading API") Configuration Path: If Innova IPSec device is detected, the mlx5e netdevice gets the new NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload capabilities, and also the matching TX checksum and GSO features. The driver configures offloaded Security Associations (SAs) by sending an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR. These messages and their responses are sent over a high-speed channel. Counters for ethtool are retrieved by the driver from the SBU. Data path: On receive path, the SBU decrypts ESP packets which match the offloaded SADB, but keeps them encapsulated. The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload has taken place, the SA with which it was done, and the authentication result. The ConnectX chip performs RX checksum offload on the packet, and RSS using the ESP SPI value. The driver detects the special ethertype, and attaches a struct secpath to the RX SKB, including flags to indicate that crypto offload took place, the authentication result, and which xfrm_state was used for decryption, in the olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate patchset will add support for that in the xfrm stack. On transmit path, the stack encapsulates the packet but does not encrypt it, and indicates in the SKB's secpath that crypto offload is to be performed and the SA to use to do so. The driver avoids performing crypto-offload for ESP fragments, and packets with IP options, as the SBU cannot currently do that. For eligible packets, the driver prepends a special ethertype with metadata instructing the hardware to perform crypto offload. The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer. The driver trims it off, because the SBU automatically appends the trailer for offloaded packets. The ConnectX chip performs TX checksum offload on inner UDP or TCP packets, and GSO for TCP packets (duplicating the prepended metadata). The segmented packets then undergo encryption in the SBU before going on the wire. Performance: We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz Using AES-NI with ESP GSO we get constant 4.1 Gbps. Using crypto offload we get constant 18 Gbps. Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately. - Ilan Tayari ==================== Signed-off-by: -
David S. Miller authored
Ivan Khoronzhuk says: ==================== net: fix sw timestamping for non PTP packets This series contains several corrections connected with timestamping for cpsw and netcp drivers based on same cpts module. Based on net/next ==================== Reviewed-by:
-
Ivan Khoronzhuk authored
There is cpts function to check if packet can be timstamped with cpts. Seems that ptp_classify_raw cover all cases listed with "case". Signed-off-by:
Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by:
-
Ivan Khoronzhuk authored
The cpts can timestmap only ptp packets at this moment, so driver cannot mark every packet as though it's going to be timestamped, only because h/w timestamping for given skb is enabled with SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result outgoing packet is not timestamped at all if it's not PTP and h/w timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS only for PTP packets. Signed-off-by:
-
Ivan Khoronzhuk authored
Move sw timestamp function close to channel submit function. Signed-off-by:
-
Joe Perches authored
Using netdev_<level>(netdev, "%s: ...", netdev->name) duplicates the name in the output. Remove those uses. Miscellanea: o Use the netif_<level> convenience macros at the same time Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in mlx4_dbg debug message Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
