The code that sets the correct out-of-channel priority depending on
the scan type was accidentally removed during a rebase.  Add it back.

Fixes: c1a75153 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Introduce and use iwl_mvm_cdb_scan_api(), which checks the family.
Most of this will go away once the 22000 firmware supports adaptive
dwell, after which the V6 scan API won't be used, but the V3 scan
*config* API will still need to be distinguished.

In any case, this gets rid of the completely bogus has_new_tx_api()
checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Detect low latency and traffic load per band.  Add support for
deciding on scan type and timings per band.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Try to detect that the AP is not using aggregation even when there's
enough traffic to make it worthwhile; if this is the case and U-APSD
is enabled then assume the AP is broken (like so many) and doesn't
enable aggregation when U-APSD is used. In this case, disconnect from
the AP and blacklist U-APSD for a potential new connection to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The primary channel is the channel that will be untouched by BT. The
secondary channel might be touched by BT.  Hence, we want the primary
to be the most active channel.  To do so, use the TCM infrastructure.

Since the BT keeps sending notifications, we can rely on them to
trigger the check. Every 10 seconds, we will check what is the most
active context and chose the right primary.

We need to wait 10 seconds before we modify the settings because
frequent changes in these settings can confuse BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The code for changing the scan priority is already implemented, but
isn't yet in use.  Now that TCM data is available, we can base the
scan priority decision on the traffic load.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc.  This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Pull networking fixes from David Miller:

 1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
    GSO/LLTX properly. From Sabrina Dubroca.

 2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.

 3) Don't uncompress in slip before rstate is initialized, from Tejaswi
    Tanikella.

 4) When using 1.x firmware on aquantia, issue a deinit before we
    hardware reset the chip, otherwise we break dirty wake WOL. From
    Igor Russkikh.

 5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.

 6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.

 7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
    from Guillaume Nault.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
  l2tp: fix race in duplicate tunnel detection
  l2tp: fix races in tunnel creation
  tun: send netlink notification when the device is modified
  tun: set the flags before registering the netdevice
  lan78xx: Don't reset the interface on open
  bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
  bnxt_en: Need to include RDMA rings in bnxt_check_rings().
  bnxt_en: Support max-mtu with VF-reps
  bnxt_en: Ignore src port field in decap filter nodes
  bnxt_en: do not allow wildcard matches for L2 flows
  bnxt_en: Fix ethtool -x crash when device is down.
  vhost: return bool from *_access_ok() functions
  vhost: fix vhost_vq_access_ok() log check
  vhost: Fix vhost_copy_to_user()
  net: aquantia: oops when shutdown on already stopped device
  net: aquantia: Regression on reset with 1.x firmware
  cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
  slip: Check if rstate is initialized before uncompressing
  lan78xx: Avoid spurious kevent 4 "error"
  lan78xx: Correctly indicate invalid OTP
  ...

Pull xen fixes from Juergen Gross:
 "A few fixes of Xen related core code and drivers"

* tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/pvh: Indicate XENFEAT_linux_rsdp_unrestricted to Xen
  xen/acpi: off by one in read_acpi_id()
  xen/acpi: upload _PSD info for non Dom0 CPUs too
  x86/xen: Delay get_cpu_cap until stack canary is established
  xen: xenbus_dev_frontend: Verify body of XS_TRANSACTION_END
  xen: xenbus: Catch closing of non existent transactions
  xen: xenbus_dev_frontend: Fix XS_TRANSACTION_END handling

Pull dma-mapping fix from Christoph Hellwig:
 "Fix for one swiotlb regression in 2.16 from Takashi"

* tag 'dma-mapping-4.17-2' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: fix unexpected swiotlb_alloc_coherent failures

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Prevent bus reference leak in mmc_blk_init()

  MMC host:
   - tmio: Fix error handling when issuing CMD23
   - jz4740: Fix race condition in IRQ mask update"

* tag 'mmc-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: tmio: Fix error handling when issuing CMD23
  mmc: core: Prevent bus reference leak in mmc_blk_init()
  mmc: jz4740: Fix race condition in IRQ mask update

Pull kdb updates from Jason Wessel:

 - fix 2032 time access issues and new compiler warnings

 - minor regression test cleanup

 - formatting fixes for end user use of kdb

* tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
  kdb: use memmove instead of overlapping memcpy
  kdb: use ktime_get_mono_fast_ns() instead of ktime_get_ts()
  kdb: bl: don't use tab character in output
  kdb: drop newline in unknown command output
  kdb: make "mdr" command repeat
  kdb: use __ktime_get_real_seconds instead of __current_kernel_time
  misc: kgdbts: Display progress of asynchronous tests

Pull microblaze updates from Michal Simek:
 "Use generic pci_mmap_resource_range()"

* tag 'microblaze-4.17-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Use generic pci_mmap_resource_range()
  microblaze: Provide pgprot_device/writecombine macros for nommu

Pull asm-generic fixes from Arnd Bergmann:
 "I have one regression fix for a minor build problem after the
  architecture removal series, plus a rework of the barriers in the
  readl/writel functions, thanks to work by Sinan Kaya:

  This started from a discussion on the linuxpcc and rdma mailing
  lists[1]. To summarize, we decided that architectures are responsible
  to serialize readl() and writel() accesses on a device MMIO space
  relative to DMA performed by that device.

  This series provides a pessimistic implementation of that behavior for
  asm-generic/io.h, which is in turn used by a number of architectures
  (h8300, microblaze, nios2, openrisc, s390, sparc, um, unicore32, and
  xtensa). Some of those presumably need no extra barriers, or something
  weaker than rmb()/wmb(), and they are advised to override the new
  default for better performance.

  For inb()/outb(), the same barriers are used, but architectures might
  want to add another barrier to outb() here if that can guarantee
  non-posted behavior (some architectures can, others cannot do that).

  The readl_relaxed()/writel_relaxed() family of functions retains the
  existing behavior with no extra barriers"

[1] https://lists.ozlabs.org/pipermail/linuxppc-dev/2018-March/170481.html

* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  io: change writeX_relaxed() to remove barriers
  io: change readX_relaxed() to remove barriers
  dts: remove cris & metag dts hard link file
  io: change inX() to have their own IO barrier overrides
  io: change outX() to have their own IO barrier overrides
  io: define stronger ordering for the default writeX() implementation
  io: define stronger ordering for the default readX() implementation
  io: define several IO & PIO barrier types for the asm-generic version

Pull virtio update from Michael Tsirkin:
 "This adds reporting hugepage stats to virtio-balloon"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: export hugetlb page allocation counts

Pull IOMMU updates from Joerg Roedel:

 - OF_IOMMU support for the Rockchip iommu driver so that it can use
   generic DT bindings

 - rework of locking in the AMD IOMMU interrupt remapping code to make
   it work better in RT kernels

 - support for improved iotlb flushing in the AMD IOMMU driver

 - support for 52-bit physical and virtual addressing in the ARM-SMMU

 - various other small fixes and cleanups

* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
  iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
  iommu/rockchip: Support sharing IOMMU between masters
  iommu/rockchip: Add runtime PM support
  iommu/rockchip: Fix error handling in init
  iommu/rockchip: Use OF_IOMMU to attach devices automatically
  iommu/rockchip: Use IOMMU device for dma mapping operations
  dt-bindings: iommu/rockchip: Add clock property
  iommu/rockchip: Control clocks needed to access the IOMMU
  iommu/rockchip: Fix TLB flush of secondary IOMMUs
  iommu/rockchip: Use iopoll helpers to wait for hardware
  iommu/rockchip: Fix error handling in attach
  iommu/rockchip: Request irqs in rk_iommu_probe()
  iommu/rockchip: Fix error handling in probe
  iommu/rockchip: Prohibit unbind and remove
  iommu/amd: Return proper error code in irq_remapping_alloc()
  iommu/amd: Make amd_iommu_devtable_lock a spin_lock
  iommu/amd: Drop the lock while allocating new irq remap table
  iommu/amd: Factor out setting the remap table for a devid
  iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
  iommu/amd: Remove the special case from alloc_irq_table()
  ...

Pull more power management updates from Rafael Wysocki:
 "These include one big-ticket item which is the rework of the idle loop
  in order to prevent CPUs from spending too much time in shallow idle
  states. It reduces idle power on some systems by 10% or more and may
  improve performance of workloads in which the idle loop overhead
  matters. This has been in the works for several weeks and it has been
  tested and reviewed quite thoroughly.

  Also included are changes that finalize the cpufreq cleanup moving
  frequency table validation from drivers to the core, a few fixes and
  cleanups of cpufreq drivers, a cpuidle documentation update and a PM
  QoS core update to mark the expected switch fall-throughs in it.

  Specifics:

   - Rework the idle loop in order to prevent CPUs from spending too
     much time in shallow idle states by making it stop the scheduler
     tick before putting the CPU into an idle state only if the idle
     duration predicted by the idle governor is long enough.

     That required the code to be reordered to invoke the idle governor
     before stopping the tick, among other things (Rafael Wysocki,
     Frederic Weisbecker, Arnd Bergmann).

   - Add the missing description of the residency sysfs attribute to the
     cpuidle documentation (Prashanth Prakash).

   - Finalize the cpufreq cleanup moving frequency table validation from
     drivers to the core (Viresh Kumar).

   - Fix a clock leak regression in the armada-37xx cpufreq driver
     (Gregory Clement).

   - Fix the initialization of the CPU performance data structures for
     shared policies in the CPPC cpufreq driver (Shunyong Yang).

   - Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
     bit (Viresh Kumar, Rafael Wysocki).

   - Mark the expected switch fall-throughs in the PM QoS core (Gustavo
     Silva)"

* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
  tick-sched: avoid a maybe-uninitialized warning
  cpufreq: Drop cpufreq_table_validate_and_show()
  cpufreq: SCMI: Don't validate the frequency table twice
  cpufreq: CPPC: Initialize shared perf capabilities of CPUs
  cpufreq: armada-37xx: Fix clock leak
  cpufreq: CPPC: Don't set transition_latency
  cpufreq: ti-cpufreq: Use builtin_platform_driver()
  cpufreq: intel_pstate: Do not include debugfs.h
  PM / QoS: mark expected switch fall-throughs
  cpuidle: Add definition of residency to sysfs documentation
  time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
  nohz: Avoid duplication of code related to got_idle_tick
  nohz: Gather tick_sched booleans under a common flag field
  cpuidle: menu: Avoid selecting shallow states with stopped tick
  cpuidle: menu: Refine idle state selection for running tick
  sched: idle: Select idle state before stopping the tick
  time: hrtimer: Introduce hrtimer_next_event_without()
  time: tick-sched: Split tick_nohz_stop_sched_tick()
  cpuidle: Return nohz hint from cpuidle_select()
  jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
  ...

Pull ktest updates from Steven Rostedt:
 "These commits have either been sitting in my INBOX or have been in my
  local tree for some time. I need to push them upstream:

   - Separate out config-bisect.pl from ktest.pl.

     This allows users to do config bisects without full ktest setup.

   - Email on status change.

     Allow the user to be emailed on test start, finish, failure, etc.

   - Other small fixes and enhancements"

* tag 'ktest-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest: (24 commits)
  ktest: Take submenu into account for grub2 menus
  ktest.pl: Add MAIL_COMMAND option to define how to send email
  ktest.pl: Use run_command to execute sending mail
  ktest.pl: Allow dodie be recursive
  ktest.pl: Kill test if mailer is not supported
  ktest.pl: Add MAIL_PATH option to define where to find the mailer
  ktest.pl: No need to print no mailer is specified when mailto is not
  Ktest: add email options to sample.config
  Ktest: Use dodie for critical falures
  Ktest: Add SigInt handling
  Ktest: Add email support
  ktest.pl: Detect if a config-bisect was interrupted
  ktest.pl: Make finding config-bisect.pl dynamic
  ktest.pl: Have ktest.pl pass -r to config-bisect.pl to reset bisect
  ktest.pl: Use diffconfig if available for failed config bisects
  ktest.pl: Allow for the config-bisect.pl output to display to console
  ktest: Use config-bisect.pl in ktest.pl
  ktest: Add standalone config-bisect.pl program
  ktest: Set do_not_reboot=y for CONFIG_BISECT_TYPE=build
  ktest: Set buildonly=1 for CONFIG_BISECT_TYPE=build
  ...

Pull UBI and UBIFS updates from Richard Weinberger:
 "Minor bug fixes and improvements"

* tag 'tags/upstream-4.17-rc1' of git://git.infradead.org/linux-ubifs:
  ubi: Reject MLC NAND
  ubifs: Remove useless parameter of lpt_heap_replace
  ubifs: Constify struct ubifs_lprops in scan_for_leb_for_idx
  ubifs: remove unnecessary assignment
  ubi: Fix error for write access
  ubi: fastmap: Don't flush fastmap work on detach
  ubifs: Check ubifs_wbuf_sync() return code

Pull UML updates from Richard Weinberger:

 - a new and faster epoll based IRQ controller and NIC driver

 - misc fixes and janitorial updates

* git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  Fix vector raw inintialization logic
  Migrate vector timers to new timer API
  um: Compile with modern headers
  um: vector: Fix an error handling path in 'vector_parse()'
  um: vector: Fix a memory allocation check
  um: vector: fix missing unlock on error in vector_net_open()
  um: Add missing EXPORT for free_irq_by_fd()
  High Performance UML Vector Network Driver
  Epoll based IRQ controller
  um: Use POSIX ucontext_t instead of struct ucontext
  um: time: Use timespec64 for persistent clock
  um: Restore symbol versions for __memcpy and memcpy

Pull ARM SoC fixes from Arnd Bergmann:
 "Here is a very small set of fixes for inclusion in linux-4.17-rc1: Two
  changes for the maintainer file, and one more fix for the newly added
  npcm platform, to enable the level 2 cache controller"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Update ASPEED entry with details
  MAINTAINERS: Migrate oxnas list to groups.io
  arm: npcm: enable L2 cache in NPCM7xx architecture

Pull nios2 update from Ley Foon Tan:
 "Use read_persistent_clock64() instead of read_persistent_clock()"

* tag 'nios2-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: Use read_persistent_clock64() instead of read_persistent_clock()

Guillaume Nault says:

====================
l2tp: tunnel creation fixes

L2TP tunnel creation is racy. We need to make sure that the tunnel
returned by l2tp_tunnel_create() isn't going to be freed while the
caller is using it. This is done in patch #1, by separating tunnel
creation from tunnel registration.

With the tunnel registration code in place, we can now check for
duplicate tunnels in a race-free way. This is done in patch #2, which
incidentally removes the last use of l2tp_tunnel_find().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We can't use l2tp_tunnel_find() to prevent l2tp_nl_cmd_tunnel_create()
from creating a duplicate tunnel. A tunnel can be concurrently
registered after l2tp_tunnel_find() returns. Therefore, searching for
duplicates must be done at registration time.

Finally, remove l2tp_tunnel_find() entirely as it isn't use anywhere
anymore.

Fixes: 309795f4 ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp_tunnel_create() inserts the new tunnel into the namespace's tunnel
list and sets the socket's ->sk_user_data field, before returning it to
the caller. Therefore, there are two ways the tunnel can be accessed
and freed, before the caller even had the opportunity to take a
reference. In practice, syzbot could crash the module by closing the
socket right after a new tunnel was returned to pppol2tp_create().

This patch moves tunnel registration out of l2tp_tunnel_create(), so
that the caller can safely hold a reference before publishing the
tunnel. This second step is done with the new l2tp_tunnel_register()
function, which is now responsible for associating the tunnel to its
socket and for inserting it into the namespace's list.

While moving the code to l2tp_tunnel_register(), a few modifications
have been done. First, the socket validation tests are done in a helper
function, for clarity. Also, modifying the socket is now done after
having inserted the tunnel to the namespace's tunnels list. This will
allow insertion to fail, without having to revert theses modifications
in the error path (a followup patch will check for duplicate tunnels
before insertion). Either the socket is a kernel socket which we
control, or it is a user-space socket for which we have a reference on
the file descriptor. In any case, the socket isn't going to be closed
from under us.

Reported-by: syzbot+fbeeb5c3b538e8545644@syzkaller.appspotmail.com
Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

I added dumping of link information about tun devices over netlink in
commit 1ec010e7 ("tun: export flags, uid, gid, queue information
over netlink"), but didn't add the missing netlink notifications when
the device's exported properties change.

This patch adds notifications when owner/group or flags are modified,
when queues are attached/detached, and when a tun fd is closed.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e7 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise, register_netdevice advertises the creation of the device with
the default flags, instead of what the user requested.
Reported-by: Thomas Haller <thaller@redhat.com>
Fixes: 1ec010e7 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 92571a1a ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.

Fix this issue by removing the lan78xx_reset call from lan78xx_open.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fixes for net.

This bug fix series include NULL pointer fixes in ethtool -x code path
and in the error clean up path when freeing IRQs, a ring accounting bug
that missed rings used by the RDMA driver, and 3 bug fixes related to TC
Flower and VF-reps.

v2: Fixed commit message of patch 4.  Changed the pound sign to $ sign
in front of the ip command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.

If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi.  Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().

Fix it by checking for !bp->bnapi in bnxt_free_irq().

Fixes: e5811b8c ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings().  Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.

Fixes: fbcfc8e4 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:

	$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.

Fixes: f484f678 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this patch the following commands would succeed as far as the
user was concerned:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01/44 action drop

The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed.  If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:02 action drop
...

There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not.  Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.

Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge more updates from Andrew Morton:

 - almost all of the rest of MM

 - kasan updates

 - lots of procfs work

 - misc things

 - lib/ updates

 - checkpatch

 - rapidio

 - ipc/shm updates

 - the start of willy's XArray conversion

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (140 commits)
  page cache: use xa_lock
  xarray: add the xa_lock to the radix_tree_root
  fscache: use appropriate radix tree accessors
  export __set_page_dirty
  unicore32: turn flush_dcache_mmap_lock into a no-op
  arm64: turn flush_dcache_mmap_lock into a no-op
  mac80211_hwsim: use DEFINE_IDA
  radix tree: use GFP_ZONEMASK bits of gfp_t for flags
  linux/const.h: refactor _BITUL and _BITULL a bit
  linux/const.h: move UL() macro to include/linux/const.h
  linux/const.h: prefix include guard of uapi/linux/const.h with _UAPI
  xen, mm: allow deferred page initialization for xen pv domains
  elf: enforce MAP_FIXED on overlaying elf segments
  fs, elf: drop MAP_FIXED usage from elf_map
  mm: introduce MAP_FIXED_NOREPLACE
  MAINTAINERS: update bouncing aacraid@adaptec.com addresses
  fs/dcache.c: add cond_resched() in shrink_dentry_list()
  include/linux/kfifo.h: fix comment
  ipc/shm.c: shm_split(): remove unneeded test for NULL shm_file_data.vm_ops
  kernel/sysctl.c: add kdoc comments to do_proc_do{u}intvec_minmax_conv_param
  ...

Remove the address_space ->tree_lock and use the xa_lock newly added to
the radix_tree_root.  Rename the address_space ->page_tree to ->i_pages,
since we don't really care that it's a tree.

[willy@infradead.org: fix nds32, fs/dax.c]
  Link: http://lkml.kernel.org/r/20180406145415.GB20605@bombadil.infradead.orgLink: http://lkml.kernel.org/r/20180313132639.17387-9-willy@infradead.orgSigned-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This results in no change in structure size on 64-bit machines as it
fits in the padding between the gfp_t and the void *.  32-bit machines
will grow the structure from 8 to 12 bytes.  Almost all radix trees are
protected with (at least) a spinlock, so as they are converted from
radix trees to xarrays, the data structures will shrink again.

Initialising the spinlock requires a name for the benefit of lockdep, so
RADIX_TREE_INIT() now needs to know the name of the radix tree it's
initialising, and so do IDR_INIT() and IDA_INIT().

Also add the xa_lock() and xa_unlock() family of wrappers to make it
easier to use the lock.  If we could rely on -fplan9-extensions in the
compiler, we could avoid all of this syntactic sugar, but that wasn't
added until gcc 4.6.

Link: http://lkml.kernel.org/r/20180313132639.17387-8-willy@infradead.orgSigned-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Don't open-code accesses to data structure internals.

Link: http://lkml.kernel.org/r/20180313132639.17387-7-willy@infradead.orgSigned-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

XFS currently contains a copy-and-paste of __set_page_dirty().  Export
it from buffer.c instead.

Link: http://lkml.kernel.org/r/20180313132639.17387-6-willy@infradead.orgSigned-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>