Skip to content

L
linux
Switch branch/tag
  1. 16 Aug, 2007 2 commits
  3. 15 Aug, 2007 2 commits
  5. 10 Aug, 2007 4 commits
    • Robert Reif's avatar
      [SPARC32]: Remove iommu from struct sbus_bus and use archdata like sparc64. · 3ac4c949
      Robert Reif authored 
      Signed-off-by: default avatarRobert Reif <reif@earthlink.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3ac4c949
    • Jesper Juhl's avatar
      SLUB: Fix format specifier in Documentation/vm/slabinfo.c · ac078602
      Jesper Juhl authored 
      There's a little problem in Documentation/vm/slabinfo.c
The code is using "%d" in a printf() call to print an 'unsigned long'.
This patch corrects it to use "%lu" instead.
Signed-off-by: default avatarJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: default avatarChristoph Lameter <clameter@sgi.com>
      ac078602
    • Christoph Lameter's avatar
      SLUB: Fix dynamic dma kmalloc cache creation · 1ceef402
      Christoph Lameter authored 
      The dynamic dma kmalloc creation can run into trouble if a
GFP_ATOMIC allocation is the first one performed for a certain size
of dma kmalloc slab.

- Move the adding of the slab to sysfs into a workqueue
  (sysfs does GFP_KERNEL allocations)
- Do not call kmem_cache_destroy() (uses slub_lock)
- Only acquire the slub_lock once and--if we cannot wait--do a trylock.

  This introduces a slight risk of the first kmalloc(x, GFP_DMA|GFP_ATOMIC)
  for a range of sizes failing due to another process holding the slub_lock.
  However, we only need to acquire the spinlock once in order to establish
  each power of two DMA kmalloc cache. The possible conflict is with the
  slub_lock taken during slab management actions (create / remove slab cache).

  It is rather typical that a driver will first fill its buffers using
  GFP_KERNEL allocations which will wait until the slub_lock can be acquired.
  Drivers will also create its slab caches first outside of an atomic
  context before starting to use atomic kmalloc from an interrupt context.

  If there are any failures then they will occur early after boot or when
  loading of multiple drivers concurrently. Drivers can already accomodate
  failures of GFP_ATOMIC for other reasons. Retries will then create the slab.
Signed-off-by: default avatarChristoph Lameter <clameter@sgi.com>
      1ceef402
    • Christoph Lameter's avatar
      SLUB: Remove checks for MAX_PARTIAL from kmem_cache_shrink · fcda3d89
      Christoph Lameter authored 
      The MAX_PARTIAL checks were supposed to be an optimization. However, slab
shrinking is a manually triggered process either through running slabinfo
or by the kernel calling kmem_cache_shrink.

If one really wants to shrink a slab then all operations should be done
regardless of the size of the partial list. This also fixes an issue that
could surface if the number of partial slabs was initially above MAX_PARTIAL
in kmem_cache_shrink and later drops below MAX_PARTIAL through the
elimination of empty slabs on the partial list (rare). In that case a few
slabs may be left off the partial list (and only be put back when they
are empty).
Signed-off-by: default avatarChristoph Lameter <clameter@sgi.com>
      fcda3d89
  7. 09 Aug, 2007 32 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7