Latest wandboard hardware revision is revd1, which brings the following
new features:

- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.

Add support for the mx6, mx6dl and mx6qp revd1 variants.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

By default, the lcdif_pre_sel mux is switched to the pll3_pfd1_540m PFD
source. If this mux is allowed to propagate rate changes to its parent,
setting the LCDIF pixel clock rate to 9 MHz, as required by the LCD
panel, will cause the pll3_pfd1_540m PFD to be switched away from its
nominal rate to 288 MHz.
This has no negative side effects, as there are no other children to
this PFD. Still, to avoid surprises, it might be preferrable to switch
to the designated video PLL (pll5_video_div) as clock source for the
LCDIF pixel clock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx-i2c driver supports automatic bus recovery via the GPIO
function of the I2C pins. Enable this functionality for the Ka-Ro
electronics TX53 modules.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Don't rely on the padctl settings established by the boot loader, but
explicitly specify the padctl values in DTB. This is also necessary to
be able to use the DTB files from the Linux kernel for future U-Boot
versions that support HW configuration via DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As the DS1339 driver now supports enabling the trickle charge feature
via DTB, add the appropriate properties to utilize this feature.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The display, that incorporates this touchpanel is obsolete and won't
be supported any more.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.

The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The current GPL only licensing on the dts files makes it very
impractical for other software components licensed under another
license.

In order to make it easier for them to reuse our device trees,
relicense our dts files first under a GPL/X11 dual-license.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As the DS1339 driver now supports enabling the trickle charge feature
via DTB, add the appropriate properties to utilize this feature.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.

The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The current GPL only licensing on the dts file makes it very
impractical for other software components licensed under another
license.

In order to make it easier for them to reuse our device trees,
relicense our dts files first under a GPL/X11 dual-license.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Contrary to later i.MX SoCs, the parallel display interface pad groups on
i.MX51 are called DISP1 and DISP2 in the Reference Manual, not DISP0 and
DISP1.

Fix this inconsistence by changing the DISP names in the i.mx51 dts.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (unit_address_vs_reg): Node /display@di0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /display@di1 has a unit name, but no reg property

Fix all these warnings by changing 'display@diX' to 'dispX'.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the built-in touchscreen controller present on MX25.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit
address format error, expected "900000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000 simple-bus unit
address format error, expected "2000000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000/pxp@020f0000
simple-bus unit address format error, expected "20f0000"
(...)

Remove the leading zeroes from unit addresses to fix the warnings.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen with W=1:

Warning (unit_address_format): Node /interrupt-controller@00a01000 unit
name should not have leading 0s
Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit address
format error, expected "900000"
Warning (simple_bus_reg): Node /soc/dma-apbh@01804000 simple-bus unit
address format error, expected "1804000"
(...)

Remove the leading zeroes from unit addresses to fix the warnings.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the Utilite Pro the CEC line is wired up to the HDMI connector.
Add the required pinctrl setting.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since commit c26ebe98 ("PCI: imx6: Add regulator support"), it is
possible to pass the 'vpcie-supply' property to describe the PCIE supply.

This way we can remove the 'regulator-always-on' property from the
regulator and have a better device tree description.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for can1 and can2 nodes on Engicam i.CoreM6 RQS
QDL module boards.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

max11801 touchscreen on Engicam iCoreM6 DualLite/Solo module is
connected via i2c1, so add max11801: touchscreen@48 on i2c1.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch replace fsl,imx-audio-sgtl5000 and use simple-audio-card
for Engicam i.CoreM6 RQS QDL platform boards.

This patch also fix, pinctrl_adumux.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6q, imx6dl icore-rqs modules share common sound nodes,
so move the sound nodes from imx6q-icore-rqs into dtsi so-that
both can share the common node details.

And also replace codec: sgtl5000@0a => sgtl5000: codec@a
on imx6q-icore-rqs.dts to [label:] node-name[@unit-address]
according to devicetree specification from ePAPER v1.1

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Linux Sound card now uses generic simple-audio-card, so add
the same along with related audmux and codec(via u2c3) for
i.CoreM6 QDL module boards.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Working items:

- 800MHz CPU
- 2GB of RAM (DDR3)
- 4GB of eMMC storage
- 1T1R WiFi 2.4 GHz
- Power management support
- 1x 10/100/1000 Mbps Ethernet WAN port
- 2x USB 2.0 Host
- PCIe
- HDMI/VGA/LVDS display
- 1x UART for RS232/422/485
- 2x UART for RS232
- 1x UART for serial console
- 1x CAN bus

Specification: http://nutsboard.org/pistachioSigned-off-by: YuanCheng Cheng <onlywig@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add initial imx6sx-softing-vining-2000 board support.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is causing issues with some specific controller configurations, as
the platform isn't power limited it's better to keep it disabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Just like the OTG port, USB H1 has no over-current detection wired up.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PPD is a product from GE Healthcare to monitor vital biometric signals.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Device Tree binding document for GE Healthcare USB Management
Controller (ACHC).
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7d-pico has an ap6212 wifi chip connected to usdhc2 port.

Add support for the usdhc2 port and to the WL_REG_ON regulator
so Wifi can be functional on this board.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE

Pull networking fixes from David Miller:

 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.

 2) Fix double-free in rmnet driver, from Dan Carpenter.

 3) INET connection socket layer can double put request sockets, fix
    from Eric Dumazet.

 4) Don't match collect metadata-mode tunnels if the device is down,
    from Haishuang Yan.

 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
    be2net driver, from Suresh Reddy.

 6) Fix scaling error in gen_estimator, from Eric Dumazet.

 7) Fix 64-bit statistics deadlock in systemport driver, from Florian
    Fainelli.

 8) Fix use-after-free in sctp_sock_dump, from Xin Long.

 9) Reject invalid BPF_END instructions in verifier, from Edward Cree.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
  Documentation: link in networking docs
  tcp: fix data delivery rate
  bpf/verifier: reject BPF_ALU64|BPF_END
  sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
  sctp: fix an use-after-free issue in sctp_sock_dump
  netvsc: increase default receive buffer size
  tcp: update skb->skb_mstamp more carefully
  net: ipv4: fix l3slave check for index returned in IP_PKTINFO
  net: smsc911x: Quieten netif during suspend
  net: systemport: Fix 64-bit stats deadlock
  net: vrf: avoid gcc-4.6 warning
  qed: remove unnecessary call to memset
  tg3: clean up redundant initialization of tnapi
  tls: make tls_sw_free_resources static
  sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
  MAINTAINERS: review Renesas DT bindings as well
  net_sched: gen_estimator: fix scaling error in bytes/packets samples
  nfp: wait for the NSP resource to appear on boot
  nfp: wait for board state before talking to the NSP
  ...

Pull more input updates from Dmitry Torokhov:
 "A second round of updates for the input subsystem:

   - a new driver for PWM-controlled vibrators

   - ucb1400 touchscreen driver had completely busted suspend/resume
     handling

   - we now handle "home" button found on some devices with Goodix
     touchscreens

   - assorted other fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Gigabyte P57 to the keyboard reset table
  Input: xpad - validate USB endpoint type during probe
  Input: ucb1400_ts - fix suspend and resume handling
  Input: edt-ft5x06 - fix access to non-existing register
  Input: elantech - make arrays debounce_packet static, reduces object code size
  Input: surface3_spi - make const array header static, reduces object code size
  Input: goodix - add support for capacitive home button
  Input: add a driver for PWM controllable vibrators
  Input: adi - make array seq static, reduces object code size

Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the
entire firmware directory.  Unfortunately it thereby also removed the
support for built-in firmware.

This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum.  The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Greg K-H <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix link in filter.txt.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.

Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>