- 18 Feb, 2011 2 commits
-
-
Mark Brown authored
The only thing that should ever be calling this is soc-core and that is built as part of the same module so doesn't need the export. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by:
Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
Signed-off-by:
-
- 16 Feb, 2011 5 commits
-
-
Vinod Koul authored
Pulseaudio doesnt work with current driver and it was root caused to absense of hw_params function and malloc_pages in it. This patch adds this and allows pa to work fine with these drivers Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
Harsha Priya <priya.harsha@intel.com> Acked-by:
-
Vinod Koul authored
This patch removes the old method of soc-audio device creation in mfld machine and makes use of new soc_register_card API to register the card Signed-off-by:
-
Vinod Koul authored
The tlv scale is defined as (min, step, mute). The mute is not supported here so put the value to 0 Signed-off-by:
-
Vinod Koul authored
This patch makes the DMIC dynamically connect to TX Mux, earlier code had erroneously made this as static path Signed-off-by:
-
Vinod Koul authored
This patch makes the codec playback rails (headset and speaker) depend on actual pins they control. This enables better power management of the codec Signed-off-by:
-
- 13 Feb, 2011 11 commits
-
-
Mark Brown authored
-
Mark Brown authored
The WM8903 interrupts are clear on read so if the WM8903 detection is enabled from platform data when the IRQ is in use (rather than using a direct signal from a GPIO) status may be lost during startup. Help users spot this misconfiguration by adding a WARN_ON(). Signed-off-by:
-
Stephen Warren authored
With the appropriate MODULE_ALIAS in place, the audio modules will be automatically loaded; there is no longer a need for manual modprobes. Signed-off-by:
Stephen Warren <swarren@nvidia.com> Signed-off-by:
-
Stephen Warren authored
Harmony has both an external mic (a regular mic jack) and an internal mic (a 0.1" two-pin header on the board). The external mic is connected to the WM8903's IN1L pin, and is supported by the current driver. The internal mic is connected to the WM8903's IN1R pin, and is not supported by the current driver. It appears that no Harmony systems were shipped with any internal mic connected; users were expected to provide their own. This makes the internal mic connection less interesting. The WM8903's Mic Bias signal is used for both of these mics. For each mic, a GPIO drives a transistor which gates whether the mic bias signal is actively connected to that mic, or isolated from it. The dual use of the mic bias for both mics makes a general-purpose complete implementation of mic detection using the mic bias complex. So, for simplicity, the internal mic is currently ignored by the driver. This patch configures the relevant GPIOs to enable the mic bias connection to the external mic, and disable the mic bias connection to the internal mic. Note that in practice, this is the default state if these GPIOs aren't configured. Signed-off-by:
-
Stephen Warren authored
Signed-off-by:
-
Stephen Warren authored
* Add jack definition for mic jack * Request wm8903 to enable mic detection * Force mic bias on, since it's required for mic detection Signed-off-by:
-
Mark Brown authored
If a widget has been force enabled then not only do we need to keep the widget itself enabled, we also need to keep any supplies the widget requires enabled. The user could force all the individual widgets on but this requires too much knowledge of device internals. Signed-off-by:
-
Dimitris Papastamos authored
On WM8994 revision D and earlier ensure proper playback robustness as some rare use cases can trigger issues. Signed-off-by:
Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by:
-
Dimitris Papastamos authored
Ensure that on disabling certain registers such as AIF1DAC1L, AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled. Similarly when enabling those registers, AIF1CLK and AIF2CLK will remain disabled. Signed-off-by:
-
Stephen Warren authored
The mic detection HW should be enabled when either mic or short detection is required, not when only both are required. Signed-off-by:
-
Stephen Warren authored
* There is no hysteresis enable field in the current datasheet. * Mic detection threshold field is only 2 bits wide. Signed-off-by:
-
- 11 Feb, 2011 7 commits
-
-
Jarkko Nikula authored
It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not called from interrupt context. This avoids WARN_ON from __gpio_get_value if sleeping gpio is registered for jack. Signed-off-by:
Jarkko Nikula <jhnikula@gmail.com> Acked-by:
-
Vinod Koul authored
This patch modifies the mfld_machine to use the new jack apis for adding the voltage zones for jack type detection. It also modifed TI sn95031 codec driver to use these new apis Signed-off-by:
-
Mark Brown authored
-
Mark Brown authored
This makes no real difference compared to the write sequencer sequence that was previously used but can run without a clock being provided. Also remove the write sequencer support code as this was the last use of it. Signed-off-by:
-
Mark Brown authored
The write sequencer sequencer sequence takes longer than is desirable as it brings up a full playback path which is not required at this point. Open coding the sequence cuts the startup time by two thirds. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Janusz Krzysztofik authored
Content of the CX20442's snd_soc_codec_driver.reg_cache_default pointed area, introduced with my recent NULL pointer dereferece fix (commit f019ee5f), occured wrong after further testing, more thorough than just booting successfully. There are two problems with it: 1) It should read (1 << CX20442_TELOUT) | (1 << CX20442_MIC), not CX20442_TELOUT | CX20442_MIC. 2) While correctly matching actual codec hardware state on boot when fixed per 1), a few more code modifications would still be required to reflect that state not only into register cache, but also force them into DAPM pins state, otherwise an inconsitency occures which may prevent further codec state changes from being applied correctly. As a result, the phone stops ringing after reboot, until someone picks up the handset for the first time. Revert that reg_cache_default content to a working, previous de facto default value of 0, in hope this change can still be accepted as an rc cycle fix. Created and tested against linux-2.6.38-rc4 Signed-off-by:
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Acked-by:
-
- 10 Feb, 2011 1 commit
-
-
Mark Brown authored
Explicitly cache the DC servo offsets for digital paths in the driver, allowing them to be preserved over suspend and resume, and ensure that we recalibrate analogue outputs paths when they are in use so that we cover any changes in the input offset. Signed-off-by:
-
- 09 Feb, 2011 14 commits
-
-
Vinod Koul authored
This patch adds soc-jack support for adding voltage zones and for detecting jack type Signed-off-by:
-
Mark Brown authored
-
Mark Brown authored
ASoC generally uses the register defaults for everything, but in some cases the hardware will default to enabling some of the DAPM widgets (clocks for example). Ensure that DAPM knows about the actual widget state at initialisation by reading the enable bits after instantiating the widgets so they don't get left enabled needlessly. Signed-off-by:
-
Mark Brown authored
The WM8903 register map does not mute the DAC by default at startup so we need to explicitly do so. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
This simplfies the code and slightly reduces the startup time. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
It causes noisy -codecs to appear in things like .codec_name. Signed-off-by:
-
Vaibhav Bedia authored
This patch modifies the Davinci i2s and mcasp drivers to make use of ioremap() instead of IO_ADDRESS() Signed-off-by:
Vaibhav Bedia <vaibhav.bedia@ti.com> Acked-by:
-
Vaibhav Bedia authored
In case of any error in probe() function, clk_disable() and clk_put() should be called if clk_enable() and clk_get() went through. Signed-off-by:
-
Vaibhav Bedia authored
This patch modifies the Davinci i2s and mcasp drivers to make use of the resource_size() helper function for readability. Signed-off-by:
-
Vinod Koul authored
This patch adds support to read the mic bias voltage when a jack is inserted. It uses ADC to measure. Signed-off-by:
-
Vinod Koul authored
This patch adds support for registering jack interupt and registering jack with core Signed-off-by:
-
