- 20 Mar, 2020 1 commit
-
-
Sakari Ailus authored
The formats added by this patch are: V4L2_PIX_FMT_SBGGR14 V4L2_PIX_FMT_SGBRG14 V4L2_PIX_FMT_SGRBG14 V4L2_PIX_FMT_SRGGB14 Signed-off-by:
Jouni Ukkonen <jouni.ukkonen@intel.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> [dg@emlix.com: rebased onto current media_tree] Signed-off-by:
Daniel Glöckner <dg@emlix.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
- 16 Mar, 2020 1 commit
-
-
Heikki Krogerus authored
This makes it possible to take advantage of the function in the device drivers. Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/r/20200302135353.56659-8-heikki.krogerus@linux.intel.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 12 Mar, 2020 38 commits
-
-
Laurent Pinchart authored
10-bit and 12-bit greyscale input data to the CSI can be written as 8-bit data to memory. Support this. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Laurent Pinchart authored
Support capturing the 10- and 12-bit greyscale formats. Signed-off-by:
-
Laurent Pinchart authored
10-bit and 12-bit greyscale input data to the CSI can be written as 8-bit data to memory. Support this. Signed-off-by:
Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by:
-
Laurent Pinchart authored
The driver doesn't really support V4L2_PIX_FMT_Y16, as there's no 16-bit greyscale media bus code defined by the kernel. It (ab)uses the format to capture 10-bit and 12-bit greyscale formats. Fix it to properly support MEDIA_BUS_FMT_Y10_1X10 and MEDIA_BUS_FMT_Y12_1X12 instead. Signed-off-by:
-
Laurent Pinchart authored
Commit 4791bd7d ("media: imx: Try colorimetry at both sink and source pads") reworked the way that formats are set on the sink pad of the CSI subdevice, and accidentally removed video field handling. Restore it by defaulting to V4L2_FIELD_NONE if the field value isn't supported, with the only two supported value being V4L2_FIELD_NONE and V4L2_FIELD_INTERLACED. Fixes: 4791bd7d ("media: imx: Try colorimetry at both sink and source pads") Signed-off-by:
-
Laurent Pinchart authored
The imx7_csi_dma_reflash() function starts by reading the unrelated register CSI_CSICR18 to then overwrite the read value with a read from register CSI_CSICR3. This is likely due to a bad copy&paste, and is not needed. Remove the extraneous read from register CSI_CSICR18. Fixes: 9e5fa4e1 ("media: imx7-media-csi: Use u32 for storing register reads") Signed-off-by:
-
Laurent Pinchart authored
Enable filtering based on CSI-2 data type. Otherwise sources that send multiple data types (such as sensors that send embedded data) will not be properly supported. They will both result in additional non-image lines being captured, and in the receiver being confused as it doesn't resynchronise on vsync. Signed-off-by:
-
Laurent Pinchart authored
Add support for the 8-, 10- and 12-bit greyscale media bus formats, and map them to the CSI-2 RAW8, RAW10 and RAW12 formats respectively. Signed-off-by:
-
Laurent Pinchart authored
Add the RESOL_CH0 register to the list of registers printed through the debugfs debug infrastructure for the driver, as it can be useful to verify proper configuration of the CSI-2 receiver. Signed-off-by:
-
Laurent Pinchart authored
The .s_stream() implementation incorrectly powers on the source when stopping the stream. Power it off instead. Fixes: 7807063b ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7") Signed-off-by:
-
Matthias Brugger authored
Check the return value of of_clk_get and print an error message if not EPROBE_DEFER. Signed-off-by:
Matthias Brugger <mbrugger@suse.com> Signed-off-by:
-
Etienne Carriere authored
Change stm32-cec driver to not print an error message when the device probe operation is deferred. Signed-off-by:
Etienne Carriere <etienne.carriere@st.com> Reviewed-by:
Philippe Cornu <philippe.cornu@st.com> Signed-off-by:
-
Etienne Carriere authored
Change stm32-cec driver to defer probe when auxiliary clock "hdmi-cec" is registered in the system not has not been probed yet. Signed-off-by:
-
Johan Hovold authored
Make sure to check that we have two alternate settings and at least one endpoint before accessing the second altsetting structure and dereferencing the endpoint arrays. This specifically avoids dereferencing NULL-pointers or corrupting memory when a device does not have the expected descriptors. Note that the sanity check in cit_get_packet_size() is not redundant as the driver is mixing looking up altsettings by index and by number, which may not coincide. Fixes: 659fefa0 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01") Fixes: 59f8b0bf ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting") Cc: stable <stable@vger.kernel.org> # 2.6.37 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
Make sure to check that we have two alternate settings and at least one endpoint before accessing the second altsetting structure and dereferencing the endpoint arrays. This specifically avoids dereferencing NULL-pointers or corrupting memory when a device does not have the expected descriptors. Note that the sanity checks in stv06xx_start() and pb0100_start() are not redundant as the driver is mixing looking up altsettings by index and by number, which may not coincide. Fixes: 8668d504 ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor") Fixes: c0b33bdc ("[media] gspca-stv06xx: support bandwidth changing") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Johan Hovold authored
Make sure to check that we have at least one endpoint before accessing the endpoint array to avoid dereferencing a NULL-pointer on stream start. Note that these sanity checks are not redundant as the driver is mixing looking up altsettings by index and by number, which need not coincide. Fixes: 1876bb92 ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge") Fixes: b282d873 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Sebastian Gross authored
As of `s5c73m3.h` the auto focus cluster in `s5c73m3_ctrls` has 5 and not 6 controls. Signed-off-by:
Sebastian Gross <sebastian.gross@emlix.com> Signed-off-by:
-
Alexandre Courbot authored
This dprintk is supposed to be informational, not an error. Set it to the same level as the other messages related to memory allocations so the kernel log does not get filled by messages during normal operation. Signed-off-by:
Alexandre Courbot <acourbot@chromium.org> Signed-off-by:
-
Ricardo Ribalda Delgado authored
The pad is now checked by v4l2_subdev_call_wappers call_g_frame_interval-> check_frame_interval-> check_pad Signed-off-by:
Ricardo Ribalda Delgado <ribalda@kernel.org> Signed-off-by:
-
Dongchun Zhu authored
From the measured hardware signal, OV5695 reset pin goes high for a short period of time during boot-up. From the sensor specification, the reset pin is active low and the DT binding defines the pin as active low, which means that the values set by the driver are inverted and thus the value requested in probe ends up high. Fix it by changing probe to request the reset GPIO initialized to high, which makes the initial state of the physical signal low. In addition, DOVDD rising must occur before DVDD rising from spec., but regulator_bulk_enable() API enables all the regulators asynchronously. Use an explicit loops of regulator_enable() instead. For power off sequence, it is required that DVDD falls first. Given the bulk API does not give any guarantee about the order of regulators, change the driver to use regulator_disable() instead. The sensor also requires a delay between reset high and first I2C transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is recommended by the vendor. Fix this as well. Signed-off-by:
Dongchun Zhu <dongchun.zhu@mediatek.com> Signed-off-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Lad Prabhakar authored
This patch adds mode table entry for capturing cropped 640x480 resolution Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Acked-by:
Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by:
-
Lad Prabhakar authored
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support for RAW8 bayer format. Signed-off-by:
-
Lad Prabhakar authored
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had some issues with rcar mipi-csi driver. The sensor never entered into LP-11 state. The powerup sequence in the datasheet[1] shows the sensor entering into LP-11 in streaming mode, so to fix this issue transitions are performed from "streaming -> standby" in the probe() after power up. With this commit the sensor is able to enter LP-11 mode during power up, as expected by some CSI-2 controllers. [1] https://publiclab.org/system/images/photos/000/023/294/original/ RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF Signed-off-by:
-
Lukas Bulwahn authored
Commit 7cbeb2e1 ("media: smiapp: Move definitions under driver directory") moved the definitions in include/media/i2c/smiapp.h into other files and removed include/media/i2c/smiapp.h. Since then, ./scripts/get_maintainer.pl --self-test complains: warning: no file matches F: include/media/i2c/smiapp.h Remove MAINTAINER file entry to this removed file and while at it, update Sakari's email address in this section. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
-
Sakari Ailus authored
Add entry for my @iki.fi e-mail address to the mailmap. Signed-off-by:
-
Bingbu Cao authored
Currently, imgu is working on 450MHz for all cases, however in some cases (input frame less than 2048x1152), the imgu did not need work in high frequency. This patch make imgu work on 200MHz if the imgu input frame is less than 2048x1152 to save power. Signed-off-by:
Bingbu Cao <bingbu.cao@intel.com> Reviewed-by:
-
Ian Kumlien authored
While upgrading from 5.5.2 -> 5.5.6 I was surprised by: ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe': tvp5150.c:(.text+0x11ac): undefined reference to `__devm_regmap_init_i2c' make: *** [Makefile:1078: vmlinux] Error 1 The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C And a quick grep showed that it was needed by more targets. Signed-off-by:
Ian Kumlien <ian.kumlien@gmail.com> Signed-off-by:
-
Marco Felsch authored
The debug output for tvp5150_selmux() isn't really intuitive. Register values are printed decimal formatted and the input/output driver states are printed as enum. Even more the "normal" output enum mapps to zero so a active output will printing output=0 and a inactive output=1. Change this by brinting the register values hex formatted and the states as more readable string. Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Marco Felsch authored
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video data and is able to auto-detect the input signal. The auto-detection does not work if the connector does not receive an input signal and the tvp5150 might not be configured correctly. This misconfiguration leads into wrong decoded video streams if the tvp5150 gets powered on before the video signal is present. Limit the supported sdtv standards according to the actual selected connector to avoid a misconfiguration. Signed-off-by:
-
Marco Felsch authored
Document the optional binding to limit the possible sdtv standards on the input connectors. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Marco Felsch authored
Use underlines to highlight optional and required properties. This is quite common for all bindings. Align descriptions and start sentence with uppercase letter. Also reword the usage of the required endpoint properties for the output port in case BT.656 should be used. Signed-off-by:
-
Marco Felsch authored
Bring the device into a working state upon a open/close call. Currently this involves only the interrupt enable/disable process but can be extended in the future. Signed-off-by:
-
Marco Felsch authored
Currently the driver notifies internal subdevs if the signal is locked or not. This information is also useful for userpace applications e.g. to switch to another input device upon a signal lost event. This commit adds the support for the userspace to subscribe to the V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events. Signed-off-by:
-
Marco Felsch authored
As documented in [1] the runtime-pm ops are used to set the device into a fully 'workable' state. Therefore it can be used to enable or disable the irqs. [1] https://www.kernel.org/doc/html/latest/power/runtime_pm.htmlSigned-off-by:
-
Michael Tretter authored
There are several debug prints in the tvp5150_parse_dt() function, which do not print the prefix, because the v4l2_subdev is not initialized, yet. Initialize the v4l2_subdev before parsing the device tree to fix the debug messages. Signed-off-by:
Michael Tretter <m.tretter@pengutronix.de> Signed-off-by:
-
Marco Felsch authored
Since commit 10d5509c ("[media] v4l2: remove g/s_crop from video ops") the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is no way to try different selections. The patch adds a helper function to select the correct selection memory space (sub-device file handle or driver state) which will be set/returned. The selection rectangle is updated if the format is FORMAT_ACTIVE and the rectangle position and/or size differs from the current set rectangle. Signed-off-by:
-
Marco Felsch authored
Currently a local copy of sel->r is made and adapted to the hardware constraints. After the adaption the value is applied to the hardware but the driver forgot to reflect the adapted value to the user space. Drop the local copy and work directly on the requested rectangle instead to fix this. Signed-off-by:
-
Marco Felsch authored
The TVP5150/1 decoders support different video input sources to their AIP1A/B pins. Possible configurations are as follows: - Analog Composite signal connected to AIP1A. - Analog Composite signal connected to AIP1B. - Analog S-Video Y (luminance) and C (chrominance) signals connected to AIP1A and AIP1B respectively. This patch extends the device tree bindings documentation to describe how the input connectors for these devices should be defined in a DT. Signed-off-by:
-
