- 12 Dec, 2018 2 commits
-
-
Jonathan Bakker authored
Make it possible to use Exynos ADC driver on S5PV210 based devices. Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Jonathan Bakker authored
S5PV210's ADC variant is almost the same as v1 except that it has 10 channels and doesn't require the pmu register Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 10 Dec, 2018 1 commit
-
-
Martin Kelly authored
Currently, we're using the devm version of some but not all functions. Switch to the devm version of iio_triggered_buffer_setup and iio_device_register to simplify the code a bit and decrease the chance of bugs. Signed-off-by: Martin Kelly <martin@martingkelly.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 08 Dec, 2018 5 commits
-
-
Mircea Caprioru authored
This patch solves the register readback issue with the bit shift. When the dac resolution was lower than the register size (ex. 12 bits out of 16 bits) the readback value was not shifted with the difference in bits and the value was higher. Also a mask is applied on the read value in order to get the value relative to the actual bit size. Fixes: 0357e488 ("iio:dac:ad5686: Refactor the driver") Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Stefan Popa authored
The AD5310R is a single channel DAC with 10-bit precision, which is part of the same family as AD5311R, except that it uses the spi interface instead of i2c. The device has a built-in 2.5V reference which is enabled by default. Another important difference is that the SPI write command operation is 16 bits long. The first four bits represent the command, while the remaining 12 bits are for data. In the control reg, DB9 and DB10 are used for power-down modes, while DB8 is the REF bit. In order to accommodate this change, a new regmap type was defined and checked accordingly. Because AD5310R does not have a readback register, the read_raw operation will return "Operation is not supported". Datasheet: Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdfSigned-off-by: Stefan Popa <stefan.popa@analog.com> Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Jeremy Fertic authored
This reverts commit 00426e99. i2c_smbus_read_byte() returns 0 when a byte with the value 0 is read from the device. This is a valid read so revert the check for 0. Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Lubomir Rintel authored
The example should follow the practice or using a generic node name instead of the precise programming model, as recommended by the DTSpec. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Andi Shyti authored
When the 'info' structure inside indio_dev is left uninitialized, a segmentation fault occurs. Check the 'info' value before using it and if it is equal to NULL, return with -EINVAL. Signed-off-by: Andi Shyti <andi@etezian.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 02 Dec, 2018 1 commit
-
-
Slawomir Stepien authored
The ret returned from ad7280_chain_setup() is needed to initialize the slave_num. Don't overwrite it with call to devm_add_action_or_reset(). Fixes: cc9c58ef ("staging: iio: adc: ad7280a: use devm_* APIs") Signed-off-by: Slawomir Stepien <sst@poczta.fm> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 01 Dec, 2018 10 commits
-
-
Nicholas Mc Guire authored
devm_kasprintf() may return NULL on failure of internal allocation thus the assignments to attr.name are not safe if not checked. On error ad7280_attr_init() returns a negative return so -ENOMEM should be OK here (passed on as return value of the probe function). To make the error case more readable a temporary iio_attr is introduced and the code refactored. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 2051f25d ("iio: adc: New driver for AD7280A Lithium Ion Battery Monitoring System2") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Lorenzo Bianconi authored
Add entry for hts221 temperature/humidity driver in MAINTAINERS file Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Stephan Gerhold authored
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
Move ad2s90 resolver driver out of staging to the main tree. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Victor Colombo <victorcolombo@gmail.com> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Victor Colombo authored
Fix the checkpatch.pl issue: "CHECK: struct mutex definition without comment". Signed-off-by: Victor Colombo <victorcolombo@gmail.com> Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
This patch removes the license boilerplate text at the top of ad2s90.c and, instead, adds the SPDX GPL-2.0 license identifier, which solves the checkpatch.pl warning: "WARNING: Missing or malformed SPDX-License-Identifier tag in line 1". Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
This patch adds the device tree binding documentation for the ad2s90 resolver-to-digital converter. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Alexandru Ardelean authored
This patch adds a max frequency check at the beginning of ad2s90_probe function so that when it is set to a value above 0.83Mhz, dev_err is called with an appropriate message and -EINVAL is returned. The defined limit is 0.83Mhz instead of 2Mhz, which is the chip's max frequency as specified in the datasheet, because, as also specified in the datasheet, a 600ns delay is expected between the application of a logic LO to CS and the application of SCLK. Since the delay is not implemented in the spi code, to satisfy it, SCLK's period should be at most 2 * 600ns, so the max frequency should be 1 / (2 * 6e-7), which gives roughly 830000Hz. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
The ad2s90 driver currently sets some spi settings (max_speed_hz and mode) at ad2s90_probe. Since the maximum frequency is a required element in DT binding for spi slave devices and because the spi mode for the device can be either (0,0) or (1,1), these settings should be handled via device tree, not in the driver's code. This patch removes them from the probe function. Note: The way in which the mentioned spi settings need to be specified on the ad2s90's node of a device tree will be documented in the future patch "dt-bindings:iio:resolver: Add docs for ad2s90". Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Matheus Tavares authored
This patch adds device tree support to ad2s90 with standard device tree id table. Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 25 Nov, 2018 16 commits
-
-
Lorenzo Bianconi authored
Generalize st_lsm6dsx_shub_read_oneshot in order to not use a fixed read length and take into account iio channel realbits for single read operations Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Colin Ian King authored
The statement is indented too much by one level, fix this by removing the extraneous tab. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Fabrice Gasnier authored
Switch off ADC when going to low power mode, in case it has been left running in buffer mode. Then re-enable it when resuming. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Fabrice Gasnier authored
Add support for runtime PM & sleep. Move all regulator and clock management to dedicated HW start/stop routines. Then rely on (runtime) PM OPS to call them. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Fabrice Gasnier authored
Move self-calibration routine to prepare routine. - This is precursor patch to ease power management handling. - This also allow to factorize few error cases (error handling). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Hans de Goede authored
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008 accelerometers. The KIOX010A HID is for the one in the base and the KIOX020A for the accelerometer in the keyboard. Since userspace does not have a way yet to deal with (or ignore) the accelerometer in the keyboard, this commit just adds the KIOX010A HID for now so that display rotation will work. Related: https://github.com/hadess/iio-sensor-proxy/issues/166Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Chris Coffey authored
This patch adds driver support for the Microchip MCP41xxx/42xxx family of digital potentiometers: DEVICE Wipers Positions Resistance (kOhm) MCP41010 1 256 10 MCP41050 1 256 50 MCP41100 1 256 100 MCP42010 2 256 10 MCP42050 2 256 50 MCP42100 2 256 100 Datasheet: http://ww1.microchip.com/downloads/en/devicedoc/11195c.pdfSigned-off-by: Chris Coffey <cmc@babblebit.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Chris Coffey authored
This patch adds device tree documentation for the Microchip MCP41xxx/42xxx family of digital potentiometers. Signed-off-by: Chris Coffey <cmc@babblebit.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Shreeya Patel authored
Most of the drivers in IIO uses irq_type as the name for storing the interrupt type and hence change the name from irq_flags to irq_type for maintaining the consistency. Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Shreeya Patel authored
There is no need to store irq_flags into the structure as it is always set to the same thing. Hence switch irq_flags to a local variable. Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Shreeya Patel authored
Make the driver use device tree instead of the platform data. Hence, use devm_gpiod_get_optional function to get the data from device tree for ldac-pin and accordingly make the needed changes in the driver. Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Shreeya Patel authored
When the kernel starts up, it kicks off compiled-in drivers that match “compatible” entries it finds in the device tree. At a later stage (when /lib/modules is available), all kernel modules that match “compatible” entries in the device tree are loaded. But if there is no dt table then there should be a fall back path with which desired kernel modules can be loaded. Hence, add of_device_id table in the i2c driver to be able to use when there is no dt table. Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Martin Blumenstingl authored
Before this patch we are registering the internal clocks (for example on Meson8b, where the SAR ADC IP block implements the divider and gate clocks) with the following names: - /soc/cbus@c1100000/adc@8680#adc_div - /soc/cbus@c1100000/adc@8680#adc_en This is bad because the common clock framework uses the clock to create a directory in <debugfs>/clk. With such name, the directory creation (silently) fails and the debugfs entry ends up being created at the debugfs root. With this change, the new clock names are: - c1108680.adc#adc_div - c1108680.adc#adc_en This matches the clock naming scheme used in the PWM, Ethernet and MMC drivers. It also fixes the problem with debugfs. The idea is shamelessly taken from commit b96e9eb6 ("pwm: meson: Fix mux clock names"). Fixes: 3921db46 ("iio: Convert to using %pOF instead of full_name") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nicholas Mc Guire authored
devm_kasprintf() may return NULL on failure of internal allocation thus the assignments to init.name are not safe if not checked. On error meson_sar_adc_clk_init() returns negative values so -ENOMEM in the (unlikely) failure case of devm_kasprintf() should be fine here. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 3adbf342 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs") Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Marcelo Schmitt authored
Add a of_device_id struct variable and subsequent call to MODULE_DEVICE_TABLE macro to complete device tree support. Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Stephan Gerhold authored
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
- 23 Nov, 2018 5 commits
-
-
Ricardo Reis Marques Silva authored
Issue found by checkpatch. CHECK: Prefer kernel type 'u32' over 'uint32_t' +static const uint32_t vbox_cursor_plane_formats[] = { CHECK: Prefer kernel type 'u32' over 'uint32_t' +static const uint32_t vbox_primary_plane_formats[] = { CHECK: Prefer kernel type 'u32' over 'uint32_t' + const uint32_t *formats; Signed-off-by: Ricardo Reis Marques Silva <ricardormsilva93@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Straube authored
The local variable ret is only used to test the return value of the call to rtl8188eu_xmitframe_complete(). Use the function directly in the if test and remove the variable ret. Signed-off-by: Michael Straube <straube.linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Straube authored
Replace tabs with spaces and/or remove spaces in declarations to cleanup whitespace. Signed-off-by: Michael Straube <straube.linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Straube authored
Add spaces around '>>' and '&' to follow kernel coding style. Reported by checkpatch. Signed-off-by: Michael Straube <straube.linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael Straube authored
Remove unnecessary parentheses in usb_ops_linux.c. Reported by checkpatch. Signed-off-by: Michael Straube <straube.linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-