- 04 Sep, 2013 21 commits
-
-
Shobhit Kumar authored
Initial parsing of the VBT MIPI block. For now, just store the panel id if found. Note: Again there seems to be no documentation for this piece of lore. The doc situation for byt+ is just a bad joke :( Signed-off-by:
Shobhit Kumar <shobhit.kumar@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Shobhit Kumar authored
Note: No one seems to have docs for this, so this patch here is just unreviewed black magic :( Signed-off-by:
ymohanma <yogesh.mohan.marimuthu@intel.com> Signed-off-by:
-
Jani Nikula authored
DPLL is not needed for DSI v2: Rebase due to added DSI PLL assertion patch. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
For DSI, we need to be asserting DSI PLL, not DPLL. This is a somewhat stopgap implementation. It's slightly ugly to have to pass the dsi parameter to intel_enable_pipe(). Signed-off-by:
-
ymohanma authored
v2: - Grab dpio_lock mutex in vlv_enable_dsi_pll(). - Add and call vlv_disable_dsi_pll(). v3: Mostly based on Ville's review comments. - Only pipe A has DSI PLL lock bit. - Add more of CCK REG bit definitions for DSI PLL. - Make tables static. - Move clock gating out of the clock calculation functions. - DSI PLL LDO power gating. - Put alternative MNP from table calc behind #ifdef. v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville). Signed-off-by:
-
Jani Nikula authored
This does not include any panel specific sub-encoders yet. v2: Fix fixed mode handling (Daniel) v3: Mostly based on Ville's review comments. - Fix MIPI_HS_TX_TIMEOUT. - DPI_ENABLE only for video mode. - Drop ULPS usage for now, use DEVICE_READY only. - Set MIPI_INIT_COUNT based on txclkesc. Signed-off-by:
-
Jani Nikula authored
v2: Rebase due to register bit definition change. v3: Mostly based on Ville's review comments. - Use size_t for length all around. - Reuse dsi_vc_send_short in dsi_vc_send_long. - Remove stale/incorrect comments. - Reverse special packet sent interrupt check. - Use DSI controller regs for reading, not adapter. Signed-off-by:
-
Jani Nikula authored
The sub-encoder model is copied from DVO. v2: Add attached_connector to struct intel_dsi. Signed-off-by:
-
Jani Nikula authored
Signed-off-by:
-
Jani Nikula authored
Add definitions for VLV MIPI DSI registers. v2: Small fixes per Ville's review comments. Signed-off-by:
-
Jani Nikula authored
v2: Add comment this is pipe A only (Ville) Signed-off-by:
-
Jani Nikula authored
For GPIO NC, CCK, CCU, and GPS CORE. Signed-off-by:
-
Shobhit Kumar authored
Signed-off-by:
Dave Airlie <airlied@gmail.com> Reviewed-by:
-
Chris Wilson authored
A follow-on to the update of the LLC coherency logic is that we can rely on the LLC being coherent with the CS for rewriting batchbuffers irrespective of their cache domain. (This should have no effect currently as all the batch buffers are expected to be I915_CACHE_LLC and so using the cpu relocation path anyway.) Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Daniel Vetter authored
The important bugfix here is that we must not unlink the vma when we keep it around as a placeholder for the execbuf code. Since then we won't find it again when execbuf gets interrupt and restarted and create a 2nd vma. And since the code as-is isn't fit yet to deal with more than one vma, hilarity ensues. Specifically the dma map/unmap of the sg table isn't adjusted for multiple vmas yet and will blow up like this: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 IP: [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915] PGD 56bb5067 PUD ad3dd067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: tcp_lp ppdev parport_pc lp parport ipv6 dm_mod dcdbas snd_hda_codec_hdmi pcspkr snd_hda_codec_realtek serio_raw i2c_i801 iTCO_wdt iTCO_vendor_support snd_hda_intel snd_hda_codec lpc_ich snd_hwdep mfd_core snd_pcm snd_page_alloc snd_timer snd soundcore acpi_cpufreq i915 video button drm_kms_helper drm mperf freq_table CPU: 1 PID: 16650 Comm: fbo-maxsize Not tainted 3.11.0-rc4_nightlytop_d93f59_debug_20130814_+ #6957 Hardware name: Dell Inc. OptiPlex 9010/03JR84, BIOS A01 05/04/2012 task: ffff8800563b3f00 ti: ffff88004bdf4000 task.ti: ffff88004bdf4000 RIP: 0010:[<ffffffffa008fb37>] [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915] RSP: 0018:ffff88004bdf5958 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8801135e0000 RCX: ffff8800ad3bf8e0 RDX: ffff8800ad3bf8e0 RSI: 0000000000000000 RDI: ffff8801007ee780 RBP: ffff88004bdf5978 R08: ffff8800ad3bf8e0 R09: 0000000000000000 R10: ffffffff86ca1810 R11: ffff880036a17101 R12: ffff8801007ee780 R13: 0000000000018001 R14: ffff880118c4e000 R15: ffff8801007ee780 FS: 00007f401a0ce740(0000) GS:ffff88011e280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000005635c000 CR4: 00000000001407e0 Stack: ffff8801007ee780 ffff88005c253180 0000000000018000 ffff8801135e0000 ffff88004bdf59a8 ffffffffa0088e55 0000000000000011 ffff8801007eec00 0000000000018000 ffff880036a17101 ffff88004bdf5a08 ffffffffa0089026 Call Trace: [<ffffffffa0088e55>] i915_vma_unbind+0xdf/0x1ab [i915] [<ffffffffa0089026>] __i915_gem_shrink+0x105/0x177 [i915] [<ffffffffa0089452>] i915_gem_object_get_pages_gtt+0x108/0x309 [i915] [<ffffffffa0085ba9>] i915_gem_object_get_pages+0x61/0x90 [i915] [<ffffffffa008f22b>] ? gen6_ppgtt_insert_entries+0x103/0x125 [i915] [<ffffffffa008a113>] i915_gem_object_pin+0x1fa/0x5df [i915] [<ffffffffa008cdfe>] i915_gem_execbuffer_reserve_object.isra.6+0x8d/0x1bc [i915] [<ffffffffa008d156>] i915_gem_execbuffer_reserve+0x229/0x367 [i915] [<ffffffffa008dbf6>] i915_gem_do_execbuffer.isra.12+0x4dc/0xf3a [i915] [<ffffffff810fc823>] ? might_fault+0x40/0x90 [<ffffffffa008eb89>] i915_gem_execbuffer2+0x187/0x222 [i915] [<ffffffffa000971c>] drm_ioctl+0x308/0x442 [drm] [<ffffffffa008ea02>] ? i915_gem_execbuffer+0x3ae/0x3ae [i915] [<ffffffff817db156>] ? __do_page_fault+0x3dd/0x481 [<ffffffff8112fdba>] vfs_ioctl+0x26/0x39 [<ffffffff811306a2>] do_vfs_ioctl+0x40e/0x451 [<ffffffff817deda7>] ? sysret_check+0x1b/0x56 [<ffffffff8113073c>] SyS_ioctl+0x57/0x87 [<ffffffff8135bbfe>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff817ded82>] system_call_fastpath+0x16/0x1b Code: 48 c7 c6 84 30 0e a0 31 c0 e8 d0 e9 f7 ff bf c6 a7 00 00 e8 07 af 2c e1 41 f6 84 24 03 01 00 00 10 75 44 49 8b 84 24 08 01 00 00 <8b> 50 08 48 8b 30 49 8b 86 b0 04 00 00 48 89 c7 48 81 c7 98 00 RIP [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915] RSP <ffff88004bdf5958> CR2: 0000000000000008 As a consequence we need to change the "only one vma for now" check in vma_unbind - since vma_destroy isn't always called the obj->vma_list might not be empty. Instead check that the vma list is singular at the beginning of vma_unbind. This is also more symmetric with bind_to_vm. This fixes the igt/gem_evict_everything|alignment testcases. v2: - Add a paranoid WARN to mark_free in the eviction code to make sure we never try to evict a vma used by the execbuf code right now. - Move the check for a temporary execbuf vma into vma_destroy - otherwise the failure path cleanup in bind_to_vm will blow up. Our first attempting at fixing this was commit 1be81a2f2cfd8789a627401d470423358fba2d76 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Tue Aug 20 12:56:40 2013 +0100 drm/i915: Don't destroy the vma placeholder during execbuffer reservation Squash with this when merging! v3: Improvements suggested in Chris' review: - Move the WARN_ON in vma_destroy that checks for vmas with an drm_mm allocation before the early return. - Bail out if we hit the WARN in mark_free to hopefully make the kernel survive for long enough to capture it. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <ben@bwidawsk.net> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68298 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68171 Tested-by: lu hua <huax.lu@intel.com> (v2) Reviewed-by: -
Chris Wilson authored
The execbuffer handle and exec_link were moved from the object into the vma. As the vma may be unbound and destroyed whilst attempting to reserve the execbuffer objects (either through a forced unbind to fix up a misalignment or through an evict-everything call) we need to prevent the free of the i915_vma itself. Otherwise not only is the list of objects to reserve corrupt, but we continue to reference stale vma entries. Fixes kernel crash with i-g-t/gem_evict_everything This regression has been introduced in commit 04038a515d6eda6dd0857c0ade0b3950d372f4c0 Author: Ben Widawsky <ben@bwidawsk.net> AuthorDate: Wed Aug 14 11:38:36 2013 +0200 drm/i915: Convert execbuf code to use vmas Reported-by:Dan Carpenter <dan.carpenter@oracle.com> References: http://www.spinics.net/lists/intel-gfx/msg32038.html Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68298Signed-off-by:
-
Daniel Vetter authored
In the execbuf code we don't clean up any vmas which ended up not getting bound for code simplicity. To make sure that we don't end up creating multiple vma for the same vm kill the somewhat dangerous vma_create function and inline it into lookup_or_create. This is just a safety measure to prevent surprises in the future. Also update the somewhat confused comment in the execbuf code and clarify what kind of magic is going on with a new one. v2: Keep the function separate as requested by Chris. But give it a __ prefix for paranoia and move it tighter together with the other vma stuff. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <ben@bwidawsk.net> Acked-by:
-
Ben Widawsky authored
In order to transition more of our code over to using a VMA instead of an <OBJ, VM> pair - we must have the vma accessible at execbuf time. Up until now, we've only had a VMA when actually binding an object. The previous patch helped handle the distinction on bound vs. unbound. This patch will help us catch leaks, and other issues before we actually shuffle a bunch of stuff around. This attempts to convert all the execbuf code to speak in vmas. Since the execbuf code is very self contained it was a nice isolated conversion. The meat of the code is about turning eb_objects into eb_vma, and then wiring up the rest of the code to use vmas instead of obj, vm pairs. Unfortunately, to do this, we must move the exec_list link from the obj structure. This list is reused in the eviction code, so we must also modify the eviction code to make this work. WARNING: This patch makes an already hotly profiled path slower. The cost is unavoidable. In reply to this mail, I will attach the extra data. v2: Release table lock early, and two a 2 phase vma lookup to avoid having to use a GFP_ATOMIC. (Chris) v3: s/obj_exec_list/obj_exec_link/ Updates to address commit 6d2b8885 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Aug 7 18:30:54 2013 +0100 drm/i915: List objects allocated from stolen memory in debugfs v4: Use obj = vma->obj for neatness in some places (Chris) need_reloc_mappable() should return false if ppgtt (Chris) Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> [danvet: Split out prep patches. Also remove a FIXME comment which is now taken care of.] Signed-off-by:
-
Daniel Vetter authored
The dpll actually runs at the port clock so we don't need to multiply it again with the pixel multiplier to get the adjusted_mode.clock. This is in contrast to the ironlake pixel clock readout code which uses the fdi dotclock: That one does _not_ run with multiplied pixels. This issue goes back to the original clock readout code added in commit f1f644dc Author: Jesse Barnes <jbarnes@virtuousgeek.org> Date: Thu Jun 27 00:39:25 2013 +0300 drm/i915: get mode clock when reading the pipe config v9 Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
The sdvo input timing needs to be the actual mode, the sdvo encoder automatically adjusts for the need of pixel doubling or quadrupling. This was lost in pipe config conversion of the pixel multiplier in commit 6cc5f341 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Wed Mar 27 00:44:53 2013 +0100 drm/i915: add pipe_config->pixel_multiplier While at it ditch the intel_ prefix from the crtc in intel_sdvo_mode_set. Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
Historically we've run our own driver hotplug handling in our own work-queue, which then launched the drm core hotplug handling in the system workqueue. This is important since we flush our own driver workqueue in the pageflip code while hodling modeset locks, and only the drm hotplug code grabbed these locks. But with commit 69787f7d Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Tue Oct 23 18:23:34 2012 +0000 drm: run the hpd irq event code directly this was changed and now we could deadlock in our flip handler if there's a hotplug work blocking the progress of the crucial unpin works. So this broke the careful deadlock avoidance implemented in commit b4a98e57 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Nov 1 09:26:26 2012 +0000 drm/i915: Flush outstanding unpin tasks before pageflipping Since the rule thus far has been that work items on our own workqueue may never grab modeset locks simply restore that rule again. v2: Add a comment to the declaration of dev_priv->wq to warn readers about the tricky implications of using it. Suggested by Chris Wilson. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Stuart Abercrombie <sabercrombie@chromium.org> Reported-by:
Stuart Abercrombie <sabercrombie@chromium.org> References: http://permalink.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/26239 Cc: stable@vger.kernel.org Reviewed-by:
-
- 03 Sep, 2013 19 commits
-
-
Daniel Vetter authored
Somehow we've lost the error handling in the patch split-up between the internal and external patch. This regression has been introduced in commit 5032d871 Author: Rafael Barbalho <rafael.barbalho@intel.com> Date: Wed Aug 21 17:10:51 2013 +0100 drm/i915: Cleaning up the relocate entry function This bug is exercised by igt/gem_reloc_vs_gpu/interruptible. Cc: Rafael Barbalho <rafael.barbalho@intel.com> Signed-off-by:
-
Ville Syrjälä authored
intel_fixed_panel_mode() overwrote the adjusted_mode with the fixed mode only partially. Notably it forgot to copy over the sync flags. The LVDS code however programmed the hardware with the sync flags from fixed mode, and then later the pipe config comparison obviously failed as we filled out the adjusted_mode in get_config from the real registers. Just call drm_mode_copy() in intel_fixed_panel_mode() to copy over the whole thing, and then just use adjusted_mode in the LVDS code to figure out which sync settings the hardware needs. Also constify the fixed_mode argument to intel_fixed_panel_mode(). Signed-off-by:
-
Damien Lespiau authored
One needs to call __sg_free_table() if __sg_alloc_table() fails, but sg_alloc_table() does that for us already. Signed-off-by:
Damien Lespiau <damien.lespiau@intel.com> Reviewd-by:
-
Alex Williamson authored
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing the memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration. v3: Use explicit LEGACY_IO | LEGACY_MEM when restoring rather than LEGACY_MASK, per Ville's comments. v2: I915_READ/WRITE accessors don't work in i915_disable_vga, use inb/outb directly. Also, on the driver unbind VGA enable path, acquire legacy IO to re-enable VGA memory. Correct comment. Signed-off-by:Alex Williamson <alex.williamson@redhat.com> Reviewed-by:
-
Alex Williamson authored
When VGA decodes change we need to do a bit more evaluation of exactly what has changed. We don't necessarily give up all the old owns resources and we need to account for resources with locks. The new algorithm is: If something is added, update decodes. If legacy resources were added and none were there before, we have a new participant. If something is removed, update decodes. If we previously owned it, we no longer own it. If it was previously locked, invalidate all locks and release it. If legacy resources were removed and none are left, remove the participant from VGA arbitration. Previously we updated decodes, released ownership of everything that was previously decoded, ignored all locks, and went off looking for another device to transfer VGA to. In a test case where Intel IGD removes only legacy VGA memory decoding, this left the arbiter switching to discrete graphics without actually disabling legacy VGA IO from the IGD. As a bonus, we bumped up the count of VGA arbitration participants for no good reason. Signed-off-by:
Dave Airlie <airlied@redhat.com> Reviewed-by:
-
Alex Williamson authored
If a device does not own a resource then we don't need to disable it. This resolves the case where an Intel IGD device can be configured to disable decode of VGA memory but we still need the arbiter to handle VGA I/O port routing. When the IGD device is in conflict, only PCI_COMMAND_IO should be disabled since VGA memory does not require arbitration on this device. Signed-off-by:
-
Chris Wilson authored
As we attempt to kmalloc after calling get_pages, there is a possibility that the shrinker may reap the pages we just acquired. To prevent this we need to increment the pages_pin_count early, so rearrange the code and error paths to make it so. Signed-off-by:
-
Paulo Zanoni authored
We shouldn't disable the trickle feed bits on Haswell. Our documentation explicitly says the trickle feed bits of PRI_CTL and CUR_CTL should not be programmed to 1, and the hardware engineer also asked us to not program the SPR_CTL field to 1. Leaving the bits as 1 could cause underflows. Reported-by:
Arthur Runyan <arthur.j.runyan@intel.com> Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
-
Jesse Barnes authored
Systems with Intel graphics controllers set aside memory exclusively for gfx driver use. This memory is not always marked in the E820 as reserved or as RAM, and so is subject to overlap from E820 manipulation later in the boot process. On some systems, MMIO space is allocated on top, despite the efforts of the "RAM buffer" approach, which simply rounds memory boundaries up to 64M to try to catch space that may decode as RAM and so is not suitable for MMIO. v2: use read_pci_config for 32 bit reads instead of adding a new one (Chris) add gen6 stolen size function (Chris) v3: use a function pointer (Chris) drop gen2 bits (Daniel) v4: call e820_sanitize_map after adding the region v5: fixup comments (Peter) simplify loop (Chris) Acked-by:Ingo Molnar <mingo@kernel.org> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by:
H. Peter Anvin <hpa@zytor.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66726 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66844Signed-off-by:
-
Jesse Barnes authored
For use by userspace (at some point in the future) and other kernel code. v2: move PCI IDs to uabi (Chris) move PCI IDs to drm/ (Dave) v3: fixup Quanta detection - needs to come first (Daniel) v4: fix up PCI match structure init for easier use by userspace (Chris) Signed-off-by: -
Joe Perches authored
The helper exists, might as well use it instead of __GFP_ZERO. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Chris Wilson authored
RCS flips do work on Iybridge+ so long as we can unmask the messages through DERRMR. However, there are quite a few workarounds mentioned regarding unmasking more than one event or triggering more than one message through DERRMR. Those workarounds in principle prevent us from performing pipelined flips (and asynchronous flips across multiple planes) and equally apply to the "known good" BCS ring. Given that it already appears to work, and also appears to work with unmasking all 3 planes at once (and queuing flips across multiple planes), be brave. Bugzlla: https://bugs.freedesktop.org/show_bug.cgi?id=67600Signed-off-by:
Stephane Marchesin <marchesin@icps.u-strasbg.fr> Cc: Stephane Marchesin <marchesin@icps.u-strasbg.fr> Cc: Ben Widawsky <ben@bwidawsk.net> Tested-by:
Stéphane Marchesin <marcheu@chromium.org> Signed-off-by:
-
Chris Wilson authored
We now have more devices using ring->private than not, and they all want the same structure. Worse, I would like to use a scratch page from outside of intel_ringbuffer.c and so for convenience would like to reuse ring->private. Embed the object into the struct intel_ringbuffer so that we can keep the code clean. Signed-off-by:
-
Imre Deak authored
If need to enable the panel fitter, the crtc timings have to be programmed according to the panel's native (fixed) mode. This isn't the case atm, since after the encoder changes adjusted_mode to fixed mode the crtc_* timing fields of adjusted_mode will stay at their original non-native values that the user passed in. This results in a corrupted output. One exception is when we have a second pass of computing encoder configs due to bandwidth limitation, since then we'll set adjusted_mode.crtc_* fields to the fixed mode values set in the first pass; so in this case things will work out. Fix this by updating the adjusted_mode.crtc_* fields when we set the fixed panel mode. This regression has been introduced in commit 135c81b8 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Sun Jul 21 21:37:09 2013 +0200 drm/i915: clean up crtc timings computation Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Daniel Vetter authored
We already have a big splashing *ERROR* for all the relevant cases of hangs, so this one here is redudant. And it results in an unclean dmesg when running with simulated hangs. Regression has been introduced in commit 05407ff8 Author: Mika Kuoppala <mika.kuoppala@linux.intel.com> Date: Thu May 30 09:04:29 2013 +0300 drm/i915: detect hang using per ring hangcheck_score Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68641Signed-off-by:
-
Chris Wilson authored
It can be useful to compare at times the current vs requested frequency of the GPU, so provide the contents of RPNSWREQ alonside CAGF. Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@gmail.com> Signed-off-by:
-
Chris Wilson authored
It appears that Valleyview shares its VGA encoder with more recent siblings and requires the same forced detection cycle after a hardware reset before we can rely on hotplugging. Reported-and-tested-by:
kobeqin <kobe.qin@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67733Tested-by:
-
Chris Wilson authored
Valleyview has its own render power state implementation with different capability knobs - it has no RP0,RP1,RPn but rather RPe. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67734Signed-off-by:
-
Mika Kuoppala authored
In reset we try to restore the forcewake state to pre reset state, using forcewake_count. The reset doesn't seem to clear the forcewake bits so we get warn on forcewake ack register not clearing. Use same mechanism as intel_uncore_sanitize() does when loading driver to reset the forcewake bits, right after the chip has been reset. Reviewed-by:
-
