Pull xtensa fix from Max Filippov:
 "Fix a section mismatch between memblock_reserve and mem_reserve.

  This fixes tinyconfig xtensa builds"

* tag 'xtensa-20190607' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: Fix section mismatch between memblock_reserve and mem_reserve

Merge tag 'kbuild-fixes-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild fixes from Masahiro Yamada:

 - fix kselftest-merge to find config fragments in deeper directories

 - fix kconfig unit test, which was broken by SPDX tag addition

 - add + prefix to buildtar to suppress jobserver unavailable warning

 - fix checkstack.pl to recognize arch=arm64

 - suppress noisy warning from cc-cross-prefix

* tag 'kbuild-fixes-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: use more portable 'command -v' for cc-cross-prefix
  scripts/checkstack.pl: Fix arm64 wrong or unknown architecture
  kbuild: tar-pkg: enable communication with jobserver
  kconfig: tests: fix recursive inclusion unit test
  kbuild: teach kselftest-merge to find nested config files

Pull MMC fixes from Ulf Hansson:
 "Here's a couple of MMC and MEMSTICK fixes:

  MMC host:
   - sdhci: Fix SDIO IRQ thread deadlock
   - sdhci-tegra: Fix a warning message
   - sdhci_am654: Fix SLOTTYPE write
   - meson-gx: Fix IRQ ack
   - tmio: Fix SCC error handling to avoid false positive CRC error

  MEMSTICK core:
   - mspro_block: Fix returning a correct error code"

* tag 'mmc-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci_am654: Fix SLOTTYPE write
  mmc: sdhci: Fix SDIO IRQ thread deadlock
  mmc: meson-gx: fix irq ack
  mmc: tmio: fix SCC error handling to avoid false positive CRC error
  mmc: tegra: Fix a warning message
  memstick: mspro_block: Fix an error code in mspro_block_issue_req()

Pull power management fixes from Rafael Wysocki:
 "These fix a crash during resume from hibernation introduced during the
  4.19 cycle, cause the new Performance and Energy Bias Hint (EPB) code
  to be built only if CONFIG_PM is set and add a few missing kerneldoc
  comments.

  Specifics:

   - Fix a crash that occurs when a kernel with 'nosmt' in the command
     line is used to resume the system from hibernation (as the
     "restore" kernel), because memory mapping differences between the
     restore and image kernels cause SMT siblings to be woken up from
     idle states and subsequently they try to fetch instructions from
     incorrect memory locations (Jiri Kosina).

   - Cause the new Performance and Energy Bias Hint (EPB) code to be
     built only if CONFIG_PM is set, because that code is not really
     necessary otherwise (Rafael Wysocki).

   - Add kerneldoc comments to documents some helper functions related
     to system-wide suspend to avoid possible confusion regarding their
     purpose (Rafael Wysocki)"

* tag 'pm-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  x86/power: Fix 'nosmt' vs hibernation triple fault during resume
  PM: sleep: Add kerneldoc comments to some functions
  x86: intel_epb: Do not build when CONFIG_PM is unset

get_desc() computes a pointer into the LDT while holding a lock that
protects the LDT from being freed, but then drops the lock and returns the
(now potentially dangling) pointer to its caller.

Fix it by giving the caller a copy of the LDT entry instead.

Fixes: 670f928b ("x86/insn-eval: Add utility function to get segment descriptor")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.

 2) Read SFP eeprom in max 16 byte increments to avoid problems with
    some SFP modules, from Russell King.

 3) Fix UDP socket lookup wrt. VRF, from Tim Beale.

 4) Handle route invalidation properly in s390 qeth driver, from Julian
    Wiedmann.

 5) Memory leak on unload in RDS, from Zhu Yanjun.

 6) sctp_process_init leak, from Neil HOrman.

 7) Fix fib_rules rule insertion semantic change that broke Android,
    from Hangbin Liu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  pktgen: do not sleep with the thread lock held.
  net: mvpp2: Use strscpy to handle stat strings
  net: rds: fix memory leak in rds_ib_flush_mr_pool
  ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
  ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
  Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
  net: aquantia: fix wol configuration not applied sometimes
  ethtool: fix potential userspace buffer overflow
  Fix memory leak in sctp_process_init
  net: rds: fix memory leak when unload rds_rdma
  ipv6: fix the check before getting the cookie in rt6_get_cookie
  ipv4: not do cache for local delivery if bc_forwarding is enabled
  s390/qeth: handle error when updating TX queue count
  s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
  s390/qeth: check dst entry before use
  s390/qeth: handle limited IPv4 broadcast in L3 TX path
  net: fix indirect calls helpers for ptype list hooks.
  net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
  udp: only choose unbound UDP socket for multicast when not in a VRF
  net/tls: replace the sleeping lock around RX resync with a bit lock
  ...

Pull rdma fixes from Jason Gunthorpe:
 "Things are looking pretty quiet here in RDMA, not too many bug fixes
  rolling in right now. The usual driver bug fixes and fixes for a
  couple of regressions introduced in 5.2:

   - Fix a race on bootup with RDMA device renaming and srp. SRP also
     needs to rename its internal sys files

   - Fix a memory leak in hns

   - Don't leak resources in efa on certain error unwinds

   - Don't panic in certain error unwinds in ib_register_device

   - Various small user visible bug fix patches for the hfi and efa
     drivers

   - Fix the 32 bit compilation break"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/efa: Remove MAYEXEC flag check from mmap flow
  mlx5: avoid 64-bit division
  IB/hfi1: Validate page aligned for a given virtual address
  IB/{qib, hfi1, rdmavt}: Correct ibv_devinfo max_mr value
  IB/hfi1: Insure freeze_work work_struct is canceled on shutdown
  IB/rdmavt: Fix alloc_qpn() WARN_ON()
  RDMA/core: Fix panic when port_data isn't initialized
  RDMA/uverbs: Pass udata on uverbs error unwind
  RDMA/core: Clear out the udata before error unwind
  RDMA/hns: Fix PD memory leak for internal allocation
  RDMA/srp: Rename SRP sysfs name after IB device rename trigger

Pull arm64 fixes from Will Deacon:
 "Another round of mostly-benign fixes, the exception being a boot crash
  on SVE2-capable CPUs (although I don't know where you'd find such a
  thing, so maybe it's benign too).

  We're in the process of resolving some big-endian ptrace breakage, so
  I'll probably have some more for you next week.

  Summary:

   - Fix boot crash on platforms with SVE2 due to missing register
     encoding

   - Fix architected timer accessors when CONFIG_OPTIMIZE_INLINING=y

   - Move cpu_logical_map into smp.h for use by upcoming irqchip drivers

   - Trivial typo fix in comment

   - Disable some useless, noisy warnings from GCC 9"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Silence gcc warnings about arch ABI drift
  ARM64: trivial: s/TIF_SECOMP/TIF_SECCOMP/ comment typo fix
  arm64: arch_timer: mark functions as __always_inline
  arm64: smp: Moved cpu_logical_map[] to smp.h
  arm64: cpufeature: Fix missing ZFR0 in __read_sysreg_by_encoding()

To print the pathname that will be used by shell in the current
environment, 'command -v' is a standardized way. [1]

'which' is also often used in scripts, but it is less portable.

When I worked on commit bd55f96f ("kbuild: refactor cc-cross-prefix
implementation"), I was eager to use 'command -v' but it did not work.
(The reason is explained below.)

I kept 'which' as before but got rid of '> /dev/null 2>&1' as I
thought it was no longer needed. Sorry, I was wrong.

It works well on my Ubuntu machine, but Alexey Brodkin reports noisy
warnings on CentOS7 when 'which' fails to find the given command in
the PATH environment.

  $ which foo
  which: no foo in (/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin)

Given that behavior of 'which' depends on system (and it may not be
installed by default), I want to try 'command -v' once again.

The specification [1] clearly describes the behavior of 'command -v'
when the given command is not found:

  Otherwise, no output shall be written and the exit status shall reflect
  that the name was not found.

However, we need a little magic to use 'command -v' from Make.

$(shell ...) passes the argument to a subshell for execution, and
returns the standard output of the command.

Here is a trick. GNU Make may optimize this by executing the command
directly instead of forking a subshell, if no shell special characters
are found in the command and omitting the subshell will not change the
behavior.

In this case, no shell special character is used. So, Make will try
to run it directly. However, 'command' is a shell-builtin command,
then Make would fail to find it in the PATH environment:

  $ make ARCH=m68k defconfig
  make: command: Command not found
  make: command: Command not found
  make: command: Command not found

In fact, Make has a table of shell-builtin commands because it must
ask the shell to execute them.

Until recently, 'command' was missing in the table.

This issue was fixed by the following commit:

| commit 1af314465e5dfe3e8baa839a32a72e83c04f26ef
| Author: Paul Smith <psmith@gnu.org>
| Date:   Sun Nov 12 18:10:28 2017 -0500
|
|     * job.c: Add "command" as a known shell built-in.
|
|     This is not a POSIX shell built-in but it's common in UNIX shells.
|     Reported by Nick Bowler <nbowler@draconx.ca>.

Because the latest release is GNU Make 4.2.1 in 2016, this commit is
not included in any released versions. (But some distributions may
have back-ported it.)

We need to trick Make to spawn a subshell. There are various ways to
do so:

 1) Use a shell special character '~' as dummy

    $(shell : ~; command -v $(c)gcc)

 2) Use a variable reference that always expands to the empty string
    (suggested by David Laight)

    $(shell command$${x:+} -v $(c)gcc)

 3) Use redirect

    $(shell command -v $(c)gcc 2>/dev/null)

I chose 3) to not confuse people. The stderr would not be polluted
anyway, but it will provide extra safety, and is easy to understand.

Tested on Make 3.81, 3.82, 4.0, 4.1, 4.2, 4.2.1

[1] http://pubs.opengroup.org/onlinepubs/9699919799/utilities/command.html

Fixes: bd55f96f ("kbuild: refactor cc-cross-prefix implementation")
Cc: linux-stable <stable@vger.kernel.org> # 5.1
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>

* pm-x86:
  x86/power: Fix 'nosmt' vs hibernation triple fault during resume
  x86: intel_epb: Do not build when CONFIG_PM is unset

Pull parisc fixes from Helge Deller:

 - Fix crashes when accessing PCI devices on some machines like C240 and
   J5000. The crashes were triggered because we replaced cache flushes
   by nops in the alternative coding where we shouldn't for some
   machines.

 - Dave fixed a race in the usage of the sr1 space register when used to
   load the coherence index.

 - Use the hardware lpa instruction to to load the physical address of
   kernel virtual addresses in the iommu driver code.

 - The kernel may fail to link when CONFIG_MLONGCALLS isn't set. Solve
   that by rearranging functions in the final vmlinux executeable.

 - Some defconfig cleanups and removal of compiler warnings.

* 'parisc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix crash due alternative coding for NP iopdir_fdc bit
  parisc: Use lpa instruction to load physical addresses in driver code
  parisc: configs: Remove useless UEVENT_HELPER_PATH
  parisc: Use implicit space register selection for loading the coherence index of I/O pdirs
  parisc: Fix compiler warnings in float emulation code
  parisc/slab: cleanup after /proc/slab_allocators removal
  parisc: Allow building 64-bit kernel without -mlong-calls compiler option
  parisc: Kconfig: remove ARCH_DISCARD_MEMBLOCK

Pull crypto fixes from Herbert Xu:
 "This fixes a regression that breaks the jitterentropy RNG and a
  potential memory leak in hmac"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: hmac - fix memory leak in hmac_init_tfm()
  crypto: jitterentropy - change back to module_init()

Pull xfs fixes from Darrick Wong:
 "Here are a couple more bug fixes for 5.2. Changes since last update:

   - Fix some forgotten strings in a log debugging function

   - Fix incorrect unit conversion in online fsck code"

* tag 'xfs-5.2-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: inode btree scrubber should calculate im_boffset correctly
  xfs: fix broken log reservation debugging

Pull gfs2 fix from Andreas Gruenbacher:
 "A revert for a patch that turned out to be broken"

* tag 'gfs2-v5.2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  Revert "gfs2: Replace gl_revokes with a GLF flag"

Pull overlayfs fixes from Miklos Szeredi:
 "Here's one fix for a class of bugs triggered by syzcaller, and one
  that makes xfstests fail less"

* tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: doc: add non-standard corner cases
  ovl: detect overlapping layers
  ovl: support the FS_IOC_FS[SG]ETXATTR ioctls

Pull fuse fixes from Miklos Szeredi:
 "This fixes a leaked inode lock in an error cleanup path and a data
  consistency issue with copy_file_range().

  It also adds a new flag for the WRITE request that allows userspace
  filesystems to clear suid/sgid bits on the file if necessary"

* tag 'fuse-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: extract helper for range writeback
  fuse: fix copy_file_range() in the writeback case
  fuse: add FUSE_WRITE_KILL_PRIV
  fuse: fallocate: fix return with locked inode

Pull NFS client fixes from Anna Schumaker:
 "These are mostly stable bugfixes found during testing, many during the
  recent NFS bake-a-thon.

  Stable bugfixes:
   - SUNRPC: Fix regression in umount of a secure mount
   - SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
   - NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
   - NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled

  Other bugfixes:
   - xprtrdma: Use struct_size() in kzalloc()"

* tag 'nfs-for-5.2-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
  NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
  SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
  SUNRPC fix regression in umount of a secure mount
  xprtrdma: Use struct_size() in kzalloc()

Currently, the process issuing a "start" command on the pktgen procfs
interface, acquires the pktgen thread lock and never release it, until
all pktgen threads are completed. The above can blocks indefinitely any
other pktgen command and any (even unrelated) netdevice removal - as
the pktgen netdev notifier acquires the same lock.

The issue is demonstrated by the following script, reported by Matteo:

ip -b - <<'EOF'
	link add type dummy
	link add type veth
	link set dummy0 up
EOF
modprobe pktgen
echo reset >/proc/net/pktgen/pgctrl
{
	echo rem_device_all
	echo add_device dummy0
} >/proc/net/pktgen/kpktgend_0
echo count 0 >/proc/net/pktgen/dummy0
echo start >/proc/net/pktgen/pgctrl &
sleep 1
rmmod veth

Fix the above releasing the thread lock around the sleep call.

Additionally we must prevent racing with forcefull rmmod - as the
thread lock no more protects from them. Instead, acquire a self-reference
before waiting for any thread. As a side effect, running

rmmod pktgen

while some thread is running now fails with "module in use" error,
before this patch such command hanged indefinitely.

Note: the issue predates the commit reported in the fixes tag, but
this fix can't be applied before the mentioned commit.

v1 -> v2:
 - no need to check for thread existence after flipping the lock,
   pktgen threads are freed only at net exit time
 -

Fixes: 6146e6a4 ("[PKTGEN]: Removes thread_{un,}lock() macros.")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ADFS cleanups/fixes from Russell King:
 "As a result of some of Al Viro's great work, here are a few cleanups
  with fixes for adfs:

   - factor out filename comparison, so we can be sure that
     adfs_compare() (used for namei compare) and adfs_match() (used for
     lookup) have the same behaviour.

   - factor out filename lowering (which is not the same as tolower()
     which will lower top-bit-set characters) to ensure that we have the
     same behaviour when comparing filenames as when we hash them.

   - factor out the object fixups, so we are applying all fixups to
     directory objects in the same way, independent of the disk format.

   - factor out the object name fixup (into the previously factored out
     function) to ensure that filenames are appropriately translated -
     for example, adfs allows '/' in filenames, which being the Unix
     path separator, need to be translated to a different character,
     which is normally '.' (DOS 8.3 filenames represent the . as a / on
     adfs, so this is the expected reverse translation.)

   - remove filename truncation; Al asked about this and apparently the
     decision is to remove it. In any case, adfs's truncation was buggy,
     so this rids us of that bug by removing the truncation feature.

   - we now have only one location which adds the "filetype" suffix to
     the filename, so there's no point that code being out of line.

   - since we translate '/' into '.', an adfs filename of "/" or "//"
     would end up being translated to "." and ".." which have special
     meanings. In this case, change the first character to "^" to avoid
     these special directory names being abused"

* tag 'for-rc-adfs' of git://git.armlinux.org.uk/~rmk/linux-arm:
  fs/adfs: fix filename fixup handling for "/" and "//" names
  fs/adfs: move append_filetype_suffix() into adfs_object_fixup()
  fs/adfs: remove truncated filename hashing
  fs/adfs: factor out filename fixup
  fs/adfs: factor out object fixups
  fs/adfs: factor out filename case lowering
  fs/adfs: factor out filename comparison

Use a safe strscpy call to copy the ethtool stat strings into the
relevant buffers, instead of a memcpy that will be accessing
out-of-bound data.

Fixes: 118d6298 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the following tests last for several hours, the problem will occur.

Server:
    rds-stress -r 1.1.1.16 -D 1M
Client:
    rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M -T 30

The following will occur.

"
Starting up....
tsks   tx/s   rx/s  tx+rx K/s    mbi K/s    mbo K/s tx us/c   rtt us cpu
%
  1      0      0       0.00       0.00       0.00    0.00 0.00 -1.00
  1      0      0       0.00       0.00       0.00    0.00 0.00 -1.00
  1      0      0       0.00       0.00       0.00    0.00 0.00 -1.00
  1      0      0       0.00       0.00       0.00    0.00 0.00 -1.00
"
>From vmcore, we can find that clean_list is NULL.

>From the source code, rds_mr_flushd calls rds_ib_mr_pool_flush_worker.
Then rds_ib_mr_pool_flush_worker calls
"
 rds_ib_flush_mr_pool(pool, 0, NULL);
"
Then in function
"
int rds_ib_flush_mr_pool(struct rds_ib_mr_pool *pool,
                         int free_all, struct rds_ib_mr **ibmr_ret)
"
ibmr_ret is NULL.

In the source code,
"
...
list_to_llist_nodes(pool, &unmap_list, &clean_nodes, &clean_tail);
if (ibmr_ret)
        *ibmr_ret = llist_entry(clean_nodes, struct rds_ib_mr, llnode);

/* more than one entry in llist nodes */
if (clean_nodes->next)
        llist_add_batch(clean_nodes->next, clean_tail, &pool->clean_list);
...
"
When ibmr_ret is NULL, llist_entry is not executed. clean_nodes->next
instead of clean_nodes is added in clean_list.
So clean_nodes is discarded. It can not be used again.
The workqueue is executed periodically. So more and more clean_nodes are
discarded. Finally the clean_list is NULL.
Then this problem will occur.

Fixes: 1bc144b6 ("net, rds, Replace xlist in net/rds/xlist.h with llist")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Olivier Matz says:

====================
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl

The following code returns EFAULT (Bad address):

  s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
  setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
  sendto(ipv6_icmp6_packet, addr);   /* returns -1, errno = EFAULT */

The problem is fixed in the second patch. The first one aligns the
code to ipv4, to avoid a race condition in the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The following code returns EFAULT (Bad address):

  s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
  setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
  sendto(ipv6_icmp6_packet, addr);   /* returns -1, errno = EFAULT */

The IPv4 equivalent code works. A workaround is to use IPPROTO_RAW
instead of IPPROTO_ICMPV6.

The failure happens because 2 bytes are eaten from the msghdr by
rawv6_probe_proto_opt() starting from commit 19e3c66b ("ipv6
equivalent of "ipv4: Avoid reading user iov twice after
raw_probe_proto_opt""), but at that time it was not a problem because
IPV6_HDRINCL was not yet introduced.

Only eat these 2 bytes if hdrincl == 0.

Fixes: 715f504b ("ipv6: add IPV6_HDRINCL option for raw sockets")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it was done in commit 8f659a03 ("net: ipv4: fix for a race
condition in raw_sendmsg") and commit 20b50d79 ("net: ipv4: emulate
READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()") for ipv4, copy the
value of inet->hdrincl in a local variable, to avoid introducing a race
condition in the next commit.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 73118ca8 introduced a glock reference counting bug in
gfs2_trans_remove_revoke.  Given that, replacing gl_revokes with a GLF flag is
no longer useful, so revert that commit.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>

Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.

The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI.  (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change.  perf and various
drivers rely on that.)

So these warnings do more harm than good: turn them off.

We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

According to the found documentation, data cache flushes and sync
instructions are needed on the PCX-U+ (PA8200, e.g. C200/C240)
platforms, while PCX-W (PA8500, e.g. C360) platforms aparently don't
need those flushes when changing the IO PDIR data structures.

We have no documentation for PCX-W+ (PA8600) and PCX-W2 (PA8700) CPUs,
but Carlo Pisani reported that his C3600 machine (PA8600, PCX-W+) fails
when the fdc instructions were removed. His firmware didn't set the NIOP
bit, so one may assume it's a firmware bug since other C3750 machines
had the bit set.

Even if documentation (as mentioned above) states that PCX-W (PA8500,
e.g.  J5000) does not need fdc flushes, Sven could show that an Adaptec
29320A PCI-X SCSI controller reliably failed on a dd command during the
first five minutes in his J5000 when fdc flushes were missing.

Going forward, we will now NOT replace the fdc and sync assembler
instructions by NOPS if:
a) the NP iopdir_fdc bit was set by firmware, or
b) we find a CPU up to and including a PCX-W+ (PA8600).

This fixes the HPMC crashes on a C240 and C36XX machines. For other
machines we rely on the firmware to set the bit when needed.

In case one finds HPMC issues, people could try to boot their machines
with the "no-alternatives" kernel option to turn off any alternative
patching.
Reported-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Carlo Pisani <carlojpisani@gmail.com>
Tested-by: Sven Schnelle <svens@stackframe.org>
Fixes: 3847dab7 ("parisc: Add alternative coding infrastructure")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.0+

Most I/O in the kernel is done using the kernel offset mapping.
However, there is one API that uses aliased kernel address ranges:

> The final category of APIs is for I/O to deliberately aliased address
> ranges inside the kernel.  Such aliases are set up by use of the
> vmap/vmalloc API.  Since kernel I/O goes via physical pages, the I/O
> subsystem assumes that the user mapping and kernel offset mapping are
> the only aliases.  This isn't true for vmap aliases, so anything in
> the kernel trying to do I/O to vmap areas must manually manage
> coherency.  It must do this by flushing the vmap range before doing
> I/O and invalidating it after the I/O returns.

For this reason, we should use the hardware lpa instruction to load the
physical address of kernel virtual addresses in the driver code.

I believe we only use the vmap/vmalloc API with old PA 1.x processors
which don't have a sba, so we don't hit this problem.

Tested on c3750, c8000 and rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a ("driver: base: Disable
   CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
   made default to 'n',
2. It is not recommended (help message: "This should not be used today
   [...] creates a high system load") and was kept only for ancient
   userland,
3. Certain userland specifically requests it to be disabled (systemd
   README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Helge Deller <deller@gmx.de>

We only support I/O to kernel space. Using %sr1 to load the coherence
index may be racy unless interrupts are disabled. This patch changes the
code used to load the coherence index to use implicit space register
selection. This saves one instruction and eliminates the race.

Tested on rp3440, c8000 and c3750.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>

Fix a s/TIF_SECOMP/TIF_SECCOMP/ comment typo

Cc: Jiri Kosina <trivial@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This reverts commit e9919a24.

Nathan reported the new behaviour breaks Android, as Android just add
new rules and delete old ones.

If we return 0 without adding dup rules, Android will remove the new
added rules and causing system to soft-reboot.

Fixes: e9919a24 ("fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Yaro Slav <yaro330@gmail.com>
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WoL magic packet configuration sometimes does not work due to
couple of leakages found.

Mainly there was a regression introduced during readx_poll refactoring.

Next, fw request waiting time was too small. Sometimes that
caused sleep proxy config function to return with an error
and to skip WoL configuration.
At last, WoL data were passed to FW from not clean buffer.
That could cause FW to accept garbage as a random configuration data.

Fixes: 6a7f2277 ("net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic")
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool_get_regs() allocates a buffer of size ops->get_regs_len(),
and pass it to the kernel driver via ops->get_regs() for filling.

There is no restriction about what the kernel drivers can or cannot do
with the open ethtool_regs structure. They usually set regs->version
and ignore regs->len or set it to the same size as ops->get_regs_len().

But if userspace allocates a smaller buffer for the registers dump,
we would cause a userspace buffer overflow in the final copy_to_user()
call, which uses the regs.len value potentially reset by the driver.

To fix this, make this case obvious and store regs.len before calling
ops->get_regs(), to only copy as much data as requested by userspace,
up to the value returned by ops->get_regs_len().

While at it, remove the redundant check for non-null regbuf.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot found the following leak in sctp_process_init
BUG: memory leak
unreferenced object 0xffff88810ef68400 (size 1024):
  comm "syz-executor273", pid 7046, jiffies 4294945598 (age 28.770s)
  hex dump (first 32 bytes):
    1d de 28 8d de 0b 1b e3 b5 c2 f9 68 fd 1a 97 25  ..(........h...%
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000a02cebbd>] kmemleak_alloc_recursive include/linux/kmemleak.h:55
[inline]
    [<00000000a02cebbd>] slab_post_alloc_hook mm/slab.h:439 [inline]
    [<00000000a02cebbd>] slab_alloc mm/slab.c:3326 [inline]
    [<00000000a02cebbd>] __do_kmalloc mm/slab.c:3658 [inline]
    [<00000000a02cebbd>] __kmalloc_track_caller+0x15d/0x2c0 mm/slab.c:3675
    [<000000009e6245e6>] kmemdup+0x27/0x60 mm/util.c:119
    [<00000000dfdc5d2d>] kmemdup include/linux/string.h:432 [inline]
    [<00000000dfdc5d2d>] sctp_process_init+0xa7e/0xc20
net/sctp/sm_make_chunk.c:2437
    [<00000000b58b62f8>] sctp_cmd_process_init net/sctp/sm_sideeffect.c:682
[inline]
    [<00000000b58b62f8>] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1384
[inline]
    [<00000000b58b62f8>] sctp_side_effects net/sctp/sm_sideeffect.c:1194
[inline]
    [<00000000b58b62f8>] sctp_do_sm+0xbdc/0x1d60 net/sctp/sm_sideeffect.c:1165
    [<0000000044e11f96>] sctp_assoc_bh_rcv+0x13c/0x200
net/sctp/associola.c:1074
    [<00000000ec43804d>] sctp_inq_push+0x7f/0xb0 net/sctp/inqueue.c:95
    [<00000000726aa954>] sctp_backlog_rcv+0x5e/0x2a0 net/sctp/input.c:354
    [<00000000d9e249a8>] sk_backlog_rcv include/net/sock.h:950 [inline]
    [<00000000d9e249a8>] __release_sock+0xab/0x110 net/core/sock.c:2418
    [<00000000acae44fa>] release_sock+0x37/0xd0 net/core/sock.c:2934
    [<00000000963cc9ae>] sctp_sendmsg+0x2c0/0x990 net/sctp/socket.c:2122
    [<00000000a7fc7565>] inet_sendmsg+0x64/0x120 net/ipv4/af_inet.c:802
    [<00000000b732cbd3>] sock_sendmsg_nosec net/socket.c:652 [inline]
    [<00000000b732cbd3>] sock_sendmsg+0x54/0x70 net/socket.c:671
    [<00000000274c57ab>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2292
    [<000000008252aedb>] __sys_sendmsg+0x80/0xf0 net/socket.c:2330
    [<00000000f7bf23d1>] __do_sys_sendmsg net/socket.c:2339 [inline]
    [<00000000f7bf23d1>] __se_sys_sendmsg net/socket.c:2337 [inline]
    [<00000000f7bf23d1>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2337
    [<00000000a8b4131f>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:3

The problem was that the peer.cookie value points to an skb allocated
area on the first pass through this function, at which point it is
overwritten with a heap allocated value, but in certain cases, where a
COOKIE_ECHO chunk is included in the packet, a second pass through
sctp_process_init is made, where the cookie value is re-allocated,
leaking the first allocation.

Fix is to always allocate the cookie value, and free it when we are done
using it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When KASAN is enabled, after several rds connections are
created, then "rmmod rds_rdma" is run. The following will
appear.

"
BUG rds_ib_incoming (Not tainted): Objects remaining
in rds_ib_incoming on __kmem_cache_shutdown()

Call Trace:
 dump_stack+0x71/0xab
 slab_err+0xad/0xd0
 __kmem_cache_shutdown+0x17d/0x370
 shutdown_cache+0x17/0x130
 kmem_cache_destroy+0x1df/0x210
 rds_ib_recv_exit+0x11/0x20 [rds_rdma]
 rds_ib_exit+0x7a/0x90 [rds_rdma]
 __x64_sys_delete_module+0x224/0x2c0
 ? __ia32_sys_delete_module+0x2c0/0x2c0
 do_syscall_64+0x73/0x190
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
"
This is rds connection memory leak. The root cause is:
When "rmmod rds_rdma" is run, rds_ib_remove_one will call
rds_ib_dev_shutdown to drop the rds connections.
rds_ib_dev_shutdown will call rds_conn_drop to drop rds
connections as below.
"
rds_conn_path_drop(&conn->c_path[0], false);
"
In the above, destroy is set to false.
void rds_conn_path_drop(struct rds_conn_path *cp, bool destroy)
{
        atomic_set(&cp->cp_state, RDS_CONN_ERROR);

        rcu_read_lock();
        if (!destroy && rds_destroy_pending(cp->cp_conn)) {
                rcu_read_unlock();
                return;
        }
        queue_work(rds_wq, &cp->cp_down_w);
        rcu_read_unlock();
}
In the above function, destroy is set to false. rds_destroy_pending
is called. This does not move rds connections to ib_nodev_conns.
So destroy is set to true to move rds connections to ib_nodev_conns.
In rds_ib_unregister_client, flush_workqueue is called to make rds_wq
finsh shutdown rds connections. The function rds_ib_destroy_nodev_conns
is called to shutdown rds connections finally.
Then rds_ib_recv_exit is called to destroy slab.

void rds_ib_recv_exit(void)
{
        kmem_cache_destroy(rds_ib_incoming_slab);
        kmem_cache_destroy(rds_ib_frag_slab);
}
The above slab memory leak will not occur again.

>From tests,
256 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma

real    0m16.522s
user    0m0.000s
sys     0m8.152s
512 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma

real    0m32.054s
user    0m0.000s
sys     0m15.568s

To rmmod rds_rdma with 256 rds connections, about 16 seconds are needed.
And with 512 rds connections, about 32 seconds are needed.
>From ftrace, when one rds connection is destroyed,

"
 19)               |  rds_conn_destroy [rds]() {
 19)   7.782 us    |    rds_conn_path_drop [rds]();
 15)               |  rds_shutdown_worker [rds]() {
 15)               |    rds_conn_shutdown [rds]() {
 15)   1.651 us    |      rds_send_path_reset [rds]();
 15)   7.195 us    |    }
 15) + 11.434 us   |  }
 19)   2.285 us    |    rds_cong_remove_conn [rds]();
 19) * 24062.76 us |  }
"
So if many rds connections will be destroyed, this function
rds_ib_destroy_nodev_conns uses most of time.
Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Jianlin's testing, netperf was broken with 'Connection reset by peer',
as the cookie check failed in rt6_check() and ip6_dst_check() always
returned NULL.

It's caused by Commit 93531c67 ("net/ipv6: separate handling of FIB
entries from dst based routes"), where the cookie can be got only when
'c1'(see below) for setting dst_cookie whereas rt6_check() is called
when !'c1' for checking dst_cookie, as we can see in ip6_dst_check().

Since in ip6_dst_check() both rt6_dst_from_check() (c1) and rt6_check()
(!c1) will check the 'from' cookie, this patch is to remove the c1 check
in rt6_get_cookie(), so that the dst_cookie can always be set properly.

c1:
  (rt->rt6i_flags & RTF_PCPU || unlikely(!list_empty(&rt->rt6i_uncached)))

Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the topo:

    h1 ---| rp1            |
          |     route  rp3 |--- h3 (192.168.200.1)
    h2 ---| rp2            |

If rp1 bc_forwarding is set while rp2 bc_forwarding is not, after
doing "ping 192.168.200.255" on h1, then ping 192.168.200.255 on
h2, and the packets can still be forwared.

This issue was caused by the input route cache. It should only do
the cache for either bc forwarding or local delivery. Otherwise,
local delivery can use the route cache for bc forwarding of other
interfaces.

This patch is to fix it by not doing cache for local delivery if
all.bc_forwarding is enabled.

Note that we don't fix it by checking route cache local flag after
rt_cache_valid() in "local_input:" and "ip_mkroute_input", as the
common route code shouldn't be touched for bc_forwarding.

Fixes: 5cbf777c ("route: add support for directed broadcast forwarding")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-kselftest-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:

 - fixes to cgroup tests (Alex Shi)

 - fix to userfaultfd compiler warning (Alakesh Haloi)

 - fix to vm install to include test script to run the test (Naresh
   Kamboju)

* tag 'linux-kselftest-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: vm: install test_vmalloc.sh for run_vmtests
  userfaultfd: selftest: fix compiler warning
  kselftest/cgroup: fix incorrect test_core skip
  kselftest/cgroup: fix unexpected testing failure on test_core
  kselftest/cgroup: fix unexpected testing failure on test_memcontrol

Pull pidfd fixes from Christian Brauner:
 "The contains two small patches to the pidfd samples and test binaries
  respectively.

  They were lacking appropriate ifdefines for __NR_pidfd_send_signal and
  could hence lead to compilation errors when that was not defined.

  This was spotted on mips independently by Guenter Roeck (who was kind
  enough to send a fix for the samples binary) and Arnd who spotted it
  in linux-next.

  Apart from these two patches, there's also a patch to update the
  comments for the pidfd_send_signal() syscall which were slightly
  wrong/inconsistenly worded"

* tag 'pidfd-fixes-v5.2-rc4' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
  tests: fix pidfd-test compilation
  signal: improve comments
  samples: fix pidfd-metadata compilation