ktime_get_ns() replaces ktime_to_ns(ktime_get())

ktime_get_real_ns() replaces ktime_to_ns(ktime_get_real())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can-next 2014-08-20

this is a pull request of 10 patches for net-next/master.

There is one patch by Wolfram Sang to clean up the build system.
Two patches by Stefan Agner that add vf610 support to the flexcan
driver. Dong Aisheng add support for bosch's m_can core, which is found
in the new freescale ARM SoCs. Sergei Shtylyov improves the rcar_can
driver by supporting all input clocks and adding device tree support.
The next patch is a small cleanup for the bit rate calculation function
by Lad, Prabhakar. And finally a patch by Himangi Saraogi, which
converts the mcp251x driver to use dmam_alloc_coherent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Event timestamp status messages have a variable length, ranging from
1 to 5 words (16 bit words). The current code however requires
a minimum message length of sizeof(*phy_txts). In most cases this
condition is fulfilled due to padding bytes. However, if several events
are signaled in a single message, padding bytes may not be present.
For short event timestamp status messages, the length check will fail,
and the event timestamp will be dropped.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8168H is Realtek PCIe Gigabit Ethernet controller.
RTL8107E is Realtek PCIe Fast Ethernet controller.

This patch add support for these two chips.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Userspace needs to be notified if one changes some option.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: Start utilizing 7.10.51

This series will enable bnx2x to start utlizing its 7.10.51 FW.
In addition, it will also add timestamping support, as well as a couple
of routine semantic cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is mostly a semantic change which modifies the code parsing and printing
of FW asserts.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prevent dereference of pointer in case it's NULL.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trying to disable sriov when VFs are assigned may lead to all kinds of problems.
This patch unifies the call in the driver to pci_disable_sriov() and prevents
them if some of the PF's child VFs are marked as assigned.

[Notice this is a bad scenario either way; User should not reach a point where
the OS tries to disable SRIOV when a VF is assigned - but currently there's no
way of preventing the user from doing so, and the ill-effect for the driver is
smaller this way]
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's possible there's a bad chip configuration which will result with
PCIe IOV capabilities, but with no available interrupts for VFs.

In such case, we want to gracefully prevent the PF from initializing its
IOV capabilities rather than encounter difficulties further along the way.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bnx2x panic dump spills a lot of information from the driver's
fastpath, but may be called while some of the fastpath is uninitialized.

This patch verifies that pointers are already allocated before dereferencing
them to prevent possible kernel panics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch does several semantic things:
  - Fixing typos.
  - Removing unnecessary prints.
  - Removing unused functions and definitions.
  - Change 'strange' usage of boolean variables.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.

The driver has been tested with linuxptp project.
Signed-off-by: Michal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

 - (L2) In some multi-function configurations, inter-PF and inter-VF
   Tx switching is incorrectly enabled.

 - (L2) Wrong assert code in FLR final cleanup in case it is sent not
   after FLR.

 - (L2) Chip may stall in very rare cases under heavy traffic with FW GRO
   enabled.

 - (L2) VF malicious notification error fixes.

 - (L2) Default gre tunnel to IPGRE which allows proper RSS for IPGRE packets,
   L2GRE traffic will reach single queue.

 - (FCoE) Fix data being placed in wrong buffer when corrupt FCoE frame is
   received.

 - (FCoE) Burst of FIP packets with destination MAC of ALL-FCF_MACs
   causes FCoE traffic to stop.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the Coccinelle semantic patch making this change
is as follows:

@change@
expression E1,E2,E3;
@@
- jiffies - E1 >= (E2*E3)
+ time_after_eq(jiffies, E1+E2*E3)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the Coccinelle semantic patch making this change
is as follows:

@change@
expression E1,E2;
@@
- (jiffies - E1) >= E2
+ time_after_eq(jiffies, E1+E2)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the Coccinelle semantic patch making this change
is as follows:

@change@
expression E1,E2;
@@
- jiffies - E1 < E2
+ time_before(jiffies, E1+E2)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the Coccinelle semantic patch making this change
is as follows:

@change@
expression E1,E2;
@@

(
- (jiffies - E1) < E2
+ time_before(jiffies, E1+E2)
)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1.   This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.

The following Coccinelle semantic patch was used:
@@
@@

- rcu_assign_pointer
+ RCU_INIT_POINTER
  (..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "rcu_dereference()" call is used directly in a condition.
Since its return value is never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacement.

The following Coccinelle semantic patch was used:
@@
@@

(
 if(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
|
 while(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "rcu_dereference()" call is used directly in a condition.
Since its return value is never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacement.

The following Coccinelle semantic patch was used:
@@
@@

(
 if(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
|
 while(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This "rcu_dereference()" call is used directly in a condition.
Since its return value is never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes this replacement.

The following Coccinelle semantic patch was used for solving it:
@@
@@

(
 if(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
 ...+>)) {...}
|
 while(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.

The following Coccinelle semantic patch was used:
@@
@@

(
 if(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
|
 while(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7a9bc9b8 ("ipv4: Elide fib_validate_source() completely when possible.")
introduced a short-circuit to avoid calling fib_validate_source when not
needed. That change took rp_filter into account, but not accept_local.
This resulted in a change of behaviour: with rp_filter and accept_local
off, incoming packets with a local address in the source field should be
dropped.

Here is how to reproduce the change pre/post 7a9bc9b8 commit:
-configure the same IPv4 address on hosts A and B.
-try to send an ARP request from B to A.
-The ARP request will be dropped before that commit, but accepted and answered
after that commit.

This adds a check for ACCEPT_LOCAL, to maintain full
fib validation in case it is 0. We also leave __fib_validate_source() earlier
when possible, based on the same check as fib_validate_source(), once the
accept_local stuff is verified.

Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the use of the function usb_endpoint_num.

The Coccinelle semantic patch that makes these changes is as follows:

@@ struct usb_endpoint_descriptor *epd; @@

- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the use of the function usb_endpoint_num.

The Coccinelle semantic patch that makes these changes is as follows:

@@ struct usb_endpoint_descriptor *epd; @@

- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the buffer is too small for a packet from VMBus, a bigger buffer will be
allocated in netvsc_channel_cb() and retry reading the packet from VMBus.
Increasing this buffer size will reduce the retry overhead.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface and does away with the calls to free the
allocated memory in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

this patch removes best_rate variable from can_calc_bittiming()
function which was set but was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support of the device tree probing for the Renesas R-Car CAN controllers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Document the R-Car CAN device tree bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When writing the driver, I didn't give enough attention to the possible sources
of the CAN clock: although the value of the CLKR register was specified by the
platform data, the driver only handled one case, that is CAN clock being
sourced from the clkp1 clock, the same that clocks the whole CAN module. In
order to fix that overlook, we'll have to handle the CAN clock separately from
the peripheral clock (however, clkp1 will be specified for a CAN device only
once)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.

Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.

M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

add M_CAN device tree binding documentation

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Extend FlexCAN driver to support Vybrid. Vybrids variant of the IP
has ECC support which is controlled through the memory error
control register (MECR). There is also an errata which leads to
false positive error detections (ID e5295). This patch disables
the memory error detection completely.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The funcion flexcan_get_berr_counter() may be called from userspace even if the
interface is down, this the clocks are disabled. This patch switches on the
clocks before accessing the ecr register.
Reported-by: Ashutosh Singh <ashuleapyear@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull more ACPI and power management updates from Rafael Wysocki:
 "These are a couple of regression fixes, cpuidle menu governor
  optimizations, fixes for ACPI proccessor and battery drivers,
  hibernation fix to avoid problems related to the e820 memory map,
  fixes for a few cpufreq drivers and a new version of the suspend
  profiling tool analyze_suspend.py.

  Specifics:

   - Fix for an ACPI-based device hotplug regression introduced in 3.14
     that causes a kernel panic to trigger when memory hot-remove is
     attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen

   - Fix for a cpufreq regression introduced in 3.16 that triggers a
     "sleeping function called from invalid context" bug in
     dev_pm_opp_init_cpufreq_table() from Stephen Boyd

   - ACPI battery driver fix for a warning message added in 3.16 that
     prints silly stuff sometimes from Mariusz Ceier

   - Hibernation fix for safer handling of mismatches in the 820 memory
     map between the configurations during image creation and during the
     subsequent restore from Chun-Yi Lee

   - ACPI processor driver fix to handle CPU hotplug notifications
     correctly during system suspend/resume from Lan Tianyu

   - Series of four cpuidle menu governor cleanups that also should
     speed it up a bit from Mel Gorman

   - Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
     cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
     Pargmann and Uwe Kleine-König

   - Version 3.0 of the analyze_suspend.py suspend profiling tool from
     Todd E Brandt"

* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / battery: Fix warning message in acpi_battery_get_state()
  PM / tools: analyze_suspend.py: update to v3.0
  cpufreq: arm_big_little: fix module license spec
  cpufreq: speedstep-smi: fix decimal printf specifiers
  ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
  cpufreq: OPP: Avoid sleeping while atomic
  cpufreq: cpu0: Do not print error message when deferring
  cpufreq: integrator: Use set_cpus_allowed_ptr
  PM / hibernate: avoid unsafe pages in e820 reserved regions
  ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
  cpuidle: menu: Lookup CPU runqueues less
  cpuidle: menu: Call nr_iowait_cpu less times
  cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
  cpuidle: menu: Use shifts when calculating averages where possible