When input GPIO set from 0 to 1, the interrupt bit asserted in the GPIO
Interrupt Cause Register (ICR) even if the corresponding interrupt
masked in the GPIO Interrupt Mask Register.

Because interrupt mask register only affects assertion of the interrupt
bits in Main Interrupt Cause Register and it does not affect the
setting of bits in the GPIO ICR.

So, there is problem, when we unmask interrupt with already
asserted bit in the GPIO ICR, then false interrupt immediately occurs
even if GPIO don't change their value since last unmask.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20200115073811.24438-1-bigunclemax@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

In the current codes, the following 3 lines would be output to
the console for each irq line.
  gpio gpiochip0: (gpio_thunderx): allocate IRQ 10, hwirq 0
  gpio gpiochip0: (gpio_thunderx): found parent hwirq 245784
  gpio gpiochip0: (gpio_thunderx): alloc_irqs_parent for 10 parent hwirq 245784

In general, there are about tens of irq lines for each gpio chip,
and then it would emit so many insignificant log in the boot process.
These infos are more suitable for the dbg purpose. So change these
to the dbg level. With this change, about 200 lines are suppressed
on my Marvell cn96xx board.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200120095625.25164-1-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio_set_config() simply call gpio_do_set_config(),
so remove the duplicated function.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200116142927.58908-1-yuehaibing@huawei.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 5.5-rc6

In commit 24258761 ("gpiolib: Add support for the irqdomain which
doesn't use irq_fwspec as arg") we have changed the return type of
gpiochip_populate_parent_fwspec_twocell/fourcell() from void to void *,
but forgot to add a return statement for these two dummy functions.
Add "return NULL" to fix the build warnings.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200116095003.30324-1-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds support to wcd934x gpio block found in
WCD9340/WC9341 Audio codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200107130844.20763-3-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/gpio/gpiolib.c: In function gpio_set_config:
drivers/gpio/gpiolib.c:3053:16: warning:
 variable config set but not used [-Wunused-but-set-variable]

commit d90f3685 ("gpiolib: have a single place
of calling set_config()") left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200108121117.45060-1-yuehaibing@huawei.comReviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

we had written "betwee" rather than "between".
Signed-off-by: Sachin agarwal <asachin591@gmail.com>
Link: https://lore.kernel.org/r/20200112143312.66048-1-sachinagarwal@sachins-MacBook-2.localSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

For consistency and easier maintenance: sort the headers alphabetically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200114150253.28716-3-brgl@bgdev.plSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The current GPL v2.0 or later SPDX tag is 'GPL-2.0-or-later' as defined
at https://spdx.org/licenses/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200114150253.28716-2-brgl@bgdev.plSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/gpio/gpio-grgpio.c: In function ‘grgpio_remove’:
drivers/gpio/gpio-grgpio.c:438:16: warning: unused variable ‘flags’ [-Wunused-variable]
  unsigned long flags;
                 ^
Fixes: 25d071b3 ("gpio: gpio-grgpio: fix possible sleep-in-atomic-context bugs in grgpio_remove()")
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1579009062-7154-1-git-send-email-zhangshaokun@hisilicon.com
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com
Reviewed-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I see the following lockdep splat in the qcom pinctrl driver when
attempting to suspend the device.

 ============================================
 WARNING: possible recursive locking detected
 5.4.2 #2 Tainted: G S
 --------------------------------------------
 cat/6536 is trying to acquire lock:
 ffffff814787ccc0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94

 but task is already holding lock:
 ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&irq_desc_lock_class);
   lock(&irq_desc_lock_class);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 7 locks held by cat/6536:
  #0: ffffff8140e0c420 (sb_writers#7){.+.+}, at: vfs_write+0xc8/0x19c
  #1: ffffff8121eec480 (&of->mutex){+.+.}, at: kernfs_fop_write+0x128/0x1f4
  #2: ffffff8147cad668 (kn->count#263){.+.+}, at: kernfs_fop_write+0x130/0x1f4
  #3: ffffffd011446000 (system_transition_mutex){+.+.}, at: pm_suspend+0x108/0x354
  #4: ffffff814302b970 (&dev->mutex){....}, at: __device_suspend+0x16c/0x420
  #5: ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
  #6: ffffff81479b8c10 (&pctrl->lock){....}, at: msm_gpio_irq_set_wake+0x48/0x7c

 stack backtrace:
 CPU: 4 PID: 6536 Comm: cat Tainted: G S                5.4.2 #2
 Call trace:
  dump_backtrace+0x0/0x174
  show_stack+0x20/0x2c
  dump_stack+0xdc/0x144
  __lock_acquire+0x52c/0x2268
  lock_acquire+0x1dc/0x220
  _raw_spin_lock_irqsave+0x64/0x80
  __irq_get_desc_lock+0x64/0x94
  irq_set_irq_wake+0x40/0x144
  msm_gpio_irq_set_wake+0x5c/0x7c
  set_irq_wake_real+0x40/0x5c
  irq_set_irq_wake+0x70/0x144
  cros_ec_rtc_suspend+0x38/0x4c
  platform_pm_suspend+0x34/0x60
  dpm_run_callback+0x64/0xcc
  __device_suspend+0x314/0x420
  dpm_suspend+0xf8/0x298
  dpm_suspend_start+0x84/0xb4
  suspend_devices_and_enter+0xbc/0x628
  pm_suspend+0x214/0x354
  state_store+0xb0/0x108
  kobj_attr_store+0x14/0x24
  sysfs_kf_write+0x4c/0x64
  kernfs_fop_write+0x158/0x1f4
  __vfs_write+0x54/0x18c
  vfs_write+0xdc/0x19c
  ksys_write+0x7c/0xe4
  __arm64_sys_write+0x20/0x2c
  el0_svc_common+0xa8/0x160
  el0_svc_compat_handler+0x2c/0x38
  el0_svc_compat+0x8/0x10

This is because the msm_gpio_irq_set_wake() function calls
irq_set_irq_wake() as a backup in case the irq comes in during the path
to idle. Given that we're calling irqchip functions from within an
irqchip we need to set the lockdep class to be different for this child
controller vs. the default one that the parent irqchip gets.

This used to be done before this driver was converted to hierarchical
irq domains in commit e35a6ae0 ("pinctrl/msm: Setup GPIO chip in
hierarchy") via the gpiochip_irq_map() function. With hierarchical irq
domains this function has been replaced by
gpiochip_hierarchy_irq_domain_alloc(). Therefore, set the lockdep class
like was done previously in the irq domain path so we can avoid this
lockdep warning.

Fixes: fdd61a01 ("gpio: Add support for hierarchical IRQ domains")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200114231103.85641-1-swboyd@chromium.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The main parts of this patch are from commit a7fc89f9 ("gpio:
thunderx: Switch to GPIOLIB_IRQCHIP") and patch [1]. And also adjust
thunderx_gpio_child_to_parent_hwirq() and add
thunderx_gpio_populate_parent_alloc_info() to make sure that
the correct hwirq are passed to the parent msi irqdomain.

[1] https://patchwork.ozlabs.org/patch/1210180/Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-5-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

If the gpio's parent irqdomain is a msi irqdomain, we should ignore
the EEXIST error returned by the msi irqdomain because all the msi
interrupts have already been allocated.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-4-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Some gpio's parent irqdomain may not use the struct irq_fwspec as
argument, such as msi irqdomain. So rename the callback
populate_parent_fwspec() to populate_parent_alloc_arg() and make it
allocate and populate the specific struct which is needed by the
parent irqdomain.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-3-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit a7fc89f9 because
there are some bugs in this commit, and we don't have a simple way to
fix these bugs. So revert this commit to make the thunderx gpio work
on the stable kernel at least. We will switch to GPIOLIB_IRQCHIP
for thunderx gpio by following patches.

Fixes: a7fc89f9 ("gpio: thunderx: Switch to GPIOLIB_IRQCHIP")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-2-haokexin@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The text in this new document is a response to recurring questions
about the GPIO in-kernel API vs the userspace ABI. When do you use
one or the other? It can be a bit intuitive, but I tried to sum it
all up.
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200108001712.47500-1-linus.walleij@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Qualcomm Technologies Inc WCD9340/WCD9341 Audio Codec has integrated
gpio controller to control 5 gpios on the chip. This patch adds
required device tree bindings for it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200107130844.20763-2-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull RISC-V fixes from Paul Walmsley:
 "Two fixes for RISC-V:

   - Clear FP registers during boot when FP support is present, rather
     than when they aren't present

   - Move the header files associated with the SiFive L2 cache
     controller to drivers/soc (where the code was recently moved)"

* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fixup obvious bug for fp-regs reset
  riscv: move sifive_l2_cache.h to include/soc

CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine
ISA Register misa. Every bit:1 indicate a feature, so we should beqz
reset_done when there is no F/D bit in csr_misa register.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[paul.walmsley@sifive.com: fix typo in commit message]
Fixes: 9e806356 ("riscv: clear the instruction cache and all registers when booting")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

The commit 9209fb51 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb51 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>

Pull iommu fixes from Joerg Roedel:

 - Two fixes for VT-d and generic IOMMU code to fix teardown on error
   handling code paths.

 - Patch for the Intel VT-d driver to fix handling of non-PCI devices

 - Fix W=1 compile warning in dma-iommu code

* tag 'iommu-fixes-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/dma: fix variable 'cookie' set but not used
  iommu/vt-d: Unlink device if failed to add to group
  iommu: Remove device link to group on failure
  iommu/vt-d: Fix adding non-PCI devices to Intel IOMMU

Pull i2c fixes from Wolfram Sang:
 "Two driver bugfixes, a documentation fix, and a removal of a spec
  violation for the bus recovery algorithm in the core"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: fix bus recovery stop mode timing
  i2c: bcm2835: Store pointer to bus clock
  dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
  i2c: at91: fix clk_offset for sam9x60

Pull thread fixes from Christian Brauner:
 "This contains a series of patches to fix CLONE_SETTLS when used with
  clone3().

  The clone3() syscall passes the tls argument through struct clone_args
  instead of a register. This means, all architectures that do not
  implement copy_thread_tls() but still support CLONE_SETTLS via
  copy_thread() expecting the tls to be located in a register argument
  based on clone() are currently unfortunately broken. Their tls value
  will be garbage.

  The patch series fixes this on all architectures that currently define
  __ARCH_WANT_SYS_CLONE3. It also adds a compile-time check to ensure
  that any architecture that enables clone3() in the future is forced to
  also implement copy_thread_tls().

  My ultimate goal is to get rid of the copy_thread()/copy_thread_tls()
  split and just have copy_thread_tls() at some point in the not too
  distant future (Maybe even renaming copy_thread_tls() back to simply
  copy_thread() once the old function is ripped from all arches). This
  is dependent now on all arches supporting clone3().

  While all relevant arches do that now there are still four missing:
  ia64, m68k, sh and sparc. They have the system call reserved, but not
  implemented. Once they all implement clone3() we can get rid of
  ARCH_WANT_SYS_CLONE3 and HAVE_COPY_THREAD_TLS.

  This series also includes a minor fix for the arm64 uapi headers which
  caused __NR_clone3 to be missing from the exported user headers.

  Unfortunately the series came in a little late especially given that
  it touches a range of architectures. Due to the holidays not all arch
  maintainers responded in time probably due to their backlog. Will and
  Arnd have thankfully acked the arm specific changes.

  Given that the changes are straightforward and rather minimal combined
  with the fact the that clone3() with CLONE_SETTLS is broken I decided
  to send them post rc3 nonetheless"

* tag 'clone3-tls-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  um: Implement copy_thread_tls
  clone3: ensure copy_thread_tls is implemented
  xtensa: Implement copy_thread_tls
  riscv: Implement copy_thread_tls
  parisc: Implement copy_thread_tls
  arm: Implement copy_thread_tls
  arm64: Implement copy_thread_tls
  arm64: Move __ARCH_WANT_SYS_CLONE3 definition to uapi headers

Pull HID fix from Jiri Kosina:
 "A regression fix for EPOLLOUT handling in hidraw and uhid"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: hidraw, uhid: Always report EPOLLOUT

Pull USB/PHY fixes from Greg KH:
 "Here are a number of USB and PHY driver fixes for 5.5-rc6

  Nothing all that unusual, just the a bunch of small fixes for a lot of
  different reported issues. The PHY driver fixes are in here as they
  interacted with the usb drivers.

  Full details of the patches are in the shortlog, and all of these have
  been in linux-next with no reported issues"

* tag 'usb-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (24 commits)
  usb: missing parentheses in USE_NEW_SCHEME
  usb: ohci-da8xx: ensure error return on variable error is set
  usb: musb: Disable pullup at init
  usb: musb: fix idling for suspend after disconnect interrupt
  usb: typec: ucsi: Fix the notification bit offsets
  USB: Fix: Don't skip endpoint descriptors with maxpacket=0
  USB-PD tcpm: bad warning+size, PPS adapters
  phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
  usb: chipidea: host: Disable port power only if previously enabled
  usb: cdns3: should not use the same dev_id for shared interrupt handler
  usb: dwc3: gadget: Fix request complete check
  usb: musb: dma: Correct parameter passed to IRQ handler
  usb: musb: jz4740: Silence error if code is -EPROBE_DEFER
  usb: udc: tegra: select USB_ROLE_SWITCH
  USB: core: fix check for duplicate endpoints
  phy: cpcap-usb: Drop extra write to usb2 register
  phy: cpcap-usb: Improve host vs docked mode detection
  phy: cpcap-usb: Prevent USB line glitches from waking up modem
  phy: mapphone-mdm6600: Fix uninitialized status value regression
  phy: cpcap-usb: Fix flakey host idling and enumerating of devices
  ...

Pull char/misc fix from Greg KH:
 "Here is a single fix, for the chrdev core, for 5.5-rc6

  There's been a long-standing race condition triggered by syzbot, and
  occasionally real people, in the chrdev open() path. Will finally took
  the time to track it down and fix it for real before the holidays.

  Here's that one patch, it's been in linux-next for a while with no
  reported issues and it does fix the reported problem"

* tag 'char-misc-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  chardev: Avoid potential use-after-free in 'chrdev_open()'

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes for 5.5-rc6.

  Nothing major here, just some small fixes for a comedi driver, the
  vt6656 driver, and a new device id for the rtl8188eu driver.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8188eu: Add device code for TP-Link TL-WN727N v5.21
  staging: comedi: adv_pci1710: fix AI channels 16-31 for PCI-1713
  staging: vt6656: set usb_set_intfdata on driver fail.
  staging: vt6656: remove bool from vnt_radio_power_on ret
  staging: vt6656: limit reg output to block size
  staging: vt6656: correct return of vnt_init_registers.
  staging: vt6656: Fix non zero logical return of, usb_control_msg

Pull tty/serial fixes from Greg KH:
 "Here are two tty/serial driver fixes for 5.5-rc6.

  The first fixes a much much reported issue with a previous tty port
  link patch that is in your tree, and the second fixes a problem where
  the serdev driver would claim ACPI devices that it shouldn't be
  claiming.

  Both have been in linux-next for a while with no reported issues"

* tag 'tty-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serdev: Don't claim unsupported ACPI serial devices
  tty: always relink the port

Pull block fixes from Jens Axboe:
 "A few fixes that should go into this round.

  This pull request contains two NVMe fixes via Keith, removal of a dead
  function, and a fix for the bio op for read truncates (Ming)"

* tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
  nvmet: fix per feat data len for get_feature
  nvme: Translate more status codes to blk_status_t
  fs: move guard_bio_eod() after bio_set_op_attrs
  block: remove unused mp_bvec_last_segment

Pull io_uring fix from Jens Axboe:
 "Single fix for this series, fixing a regression with the short read
  handling.

  This just removes it, as it cannot safely be done for all cases"

* tag 'io_uring-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
  io_uring: remove punt of short reads to async context

Pull MTD fixes from Miquel Raynal:
 "MTD:
   - sm_ftl: Fix NULL pointer warning.

  Raw NAND:
   - Cadence: fix compile testing.
   - STM32: Avoid locking.

  Onenand:
   - Fix several sparse/build warnings.

  SPI-NOR:
   - Add a flag to fix interaction with Micron parts"

* tag 'mtd/fixes-for-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: spi-nor: Fix the writing of the Status Register on micron flashes
  mtd: sm_ftl: fix NULL pointer warning
  mtd: onenand: omap2: Pass correct flags for prep_dma_memcpy
  mtd: onenand: samsung: Fix iomem access with regular memcpy
  mtd: onenand: omap2: Fix errors in style
  mtd: cadence: Fix cast to pointer from integer of different size warning
  mtd: rawnand: stm32_fmc2: avoid to lock the CPU bus

Pull sound fixes from Takashi Iwai:
 "A few piled ASoC fixes and usual HD-audio and USB-audio fixups. Some
  of them are for ASoC core error-handling"

* tag 'sound-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda: enable regmap internal locking
  ALSA: hda/realtek - Add quirk for the bass speaker on Lenovo Yoga X1 7th gen
  ALSA: hda/realtek - Set EAPD control to default for ALC222
  ALSA: usb-audio: Apply the sample rate quirk for Bose Companion 5
  ALSA: hda/realtek - Add new codec supported for ALCS1200A
  ASoC: Intel: boards: Fix compile-testing RT1011/RT5682
  ASoC: SOF: imx8: Fix dsp_box offset
  ASoC: topology: Prevent use-after-free in snd_soc_get_pcm_runtime()
  ASoC: fsl_audmix: add missed pm_runtime_disable
  ASoC: stm32: spdifrx: fix input pin state management
  ASoC: stm32: spdifrx: fix race condition in irq handler
  ASoC: stm32: spdifrx: fix inconsistent lock state
  ASoC: core: Fix access to uninitialized list heads
  ASoC: soc-core: Set dpcm_playback / dpcm_capture
  ASoC: SOF: imx8: fix memory allocation failure check on priv->pd_dev
  ASoC: SOF: Intel: hda: hda-dai: fix oops on hda_link .hw_free
  ASoC: SOF: fix fault at driver unload after failed probe

Pull thermal fix from Daniel Lezcano:
 "Fix backward compatibility with old DTBs on QCOM tsens (Amit
  Kucheria)"

* tag 'thermal-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  drivers: thermal: tsens: Work with old DTBs

Pull power management fixes from Rafael Wysocki:
 "Prevent the cpufreq-dt driver from probing Tegra20/30 (Dmitry
  Osipenko) and prevent the Intel RAPL power capping driver from
  crashing during CPU initialization due to a NULL pointer dereference
  if the processor model in use is not known to it (Harry Pan)"

* tag 'pm-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  powercap: intel_rapl: add NULL pointer check to rapl_mmio_cpu_online()
  cpufreq: dt-platdev: Blacklist NVIDIA Tegra20 and Tegra30 SoCs

The existing implementation for the get_feature admin-cmd does not
use per-feature data len. This patch introduces a new helper function
nvmet_feat_data_len(), which is used to calculate per feature data len.
Right now we only set data len for fid 0x81 (NVME_FEAT_HOST_ID).

Fixes: commit e9061c39 ("nvmet: Remove the data_len field from the nvmet_req struct")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Amit Engel <amit.engel@dell.com>
[endiness, naming, and kernel style fixes]
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Decode interrupted command and not ready namespace nvme status codes to
BLK_STS_TARGET. These are not generic IO errors and should use a non-path
specific error so that it can use the non-failover retry path.
Reported-by: John Meneghini <John.Meneghini@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e746 ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>