Attempting to try and turn off disconnected display hw in the
hotput handler lead to more problems than it helped.  For
now just register an event and only attempt the do something
interesting with DP.  Other connectors are just too problematic:
- Some systems have an HPD pin assigned to LVDS, but it's rarely
if ever connected properly and we don't really care about hpd
events on LVDS anyway since it's always connected.
- The HPD pin is wired up correctly for eDP, but we don't really
have to do anything since the events since it's always connected.
- Some HPD pins fire more than once when you connect/disconnect
- etc.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39882Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

At least some Apples program the GPU into a state that wedges the engine
once userspace starts trying to perform accelerated operations. Executing
the Atom init scripts gets the hardware back into a working state. The
same hardware works fine when booted via BIOS emulation, so let's just
execute the init scripts on Apples when we're using EFI.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We have two sources of information about panel capabilities on mobile
radeon - the BIOS, which gives us a native mode, and the panel's preferred
mode. In theory these two will always match, but there's some corner cases
where the BIOS hasn't been fully initialised and so the native mode in it
ends up with default values. However, if we get a panel with reasonable
EDID, it's probably the case that the panel's preferred mode does actually
represent the panel capabilities. This patch handles that case by replacing
the native mode with the panel's preferred mode if the resolutions don't
match. Systems without a valid internal panel EDID will still use the BIOS
native mode.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

If we get a hotplug event on an connector that is off, don't
attempt to turn it on or off, it should already be off.

Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=728228Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

The patch http://lkml.org/lkml/2003/7/13/226 introduced an RLIMIT_NPROC
check in set_user() to check for NPROC exceeding via setuid() and
similar functions.

Before the check there was a possibility to greatly exceed the allowed
number of processes by an unprivileged user if the program relied on
rlimit only.  But the check created new security threat: many poorly
written programs simply don't check setuid() return code and believe it
cannot fail if executed with root privileges.  So, the check is removed
in this patch because of too often privilege escalations related to
buggy programs.

The NPROC can still be enforced in the common code flow of daemons
spawning user processes.  Most of daemons do fork()+setuid()+execve().
The check introduced in execve() (1) enforces the same limit as in
setuid() and (2) doesn't create similar security issues.

Neil Brown suggested to track what specific process has exceeded the
limit by setting PF_NPROC_EXCEEDED process flag.  With the change only
this process would fail on execve(), and other processes' execve()
behaviour is not changed.

Solar Designer suggested to re-check whether NPROC limit is still
exceeded at the moment of execve().  If the process was sleeping for
days between set*uid() and execve(), and the NPROC counter step down
under the limit, the defered execve() failure because NPROC limit was
exceeded days ago would be unexpected.  If the limit is not exceeded
anymore, we clear the flag on successful calls to execve() and fork().

The flag is also cleared on successful calls to set_user() as the limit
was exceeded for the previous user, not the current one.

Similar check was introduced in -ow patches (without the process flag).

v3 - clear PF_NPROC_EXCEEDED on successful calls to set_user().
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf symbols: Check '/tmp/perf-' symbol file ownership
  perf sched: Usage leftover from trace -> script rename
  perf sched: Do not delete session object prematurely
  perf tools: Check $HOME/.perfconfig ownership
  perf, x86: Add model 45 SandyBridge support
  perf tools: Add support to install perf python extension
  perf tools: do not look at ./config for configuration
  perf tools: Make clean leaves some files
  perf lock: Dropping unsupported ':r' modifier
  perf probe: Fix coredump introduced by probe module option
  jump label: Reduce the cycle count by changing the link order
  perf report: Use ui__warning in some more places
  perf python: Add PERF_RECORD_{LOST,READ,SAMPLE} routine tables
  perf evlist: Introduce 'disable' method
  trace events: Update version number reference to new 3.x scheme for EVENT_POWER_TRACING_DEPRECATED
  perf buildid-cache: Zero out buffer of filenames when adding/removing buildid

Change to new git tree -
 (git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit af9d220b.

It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PNFS_BLOCK needs BLK_DEV_DM/MD, which is not a dependency for other
pnfs layout drivers. Seperate it out so others can still build when
BLK_DEV_DM/MD is not enabled.

Also change select to depends on to avoid build failures.
Reported-and-tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Peng Tao <peng_tao@emc.com>
Acked-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
  ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
  ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
  ARM: 7010/1: mm: fix invalid loop for poison_init_mem
  ARM: 7005/1: freshen up mm/proc-arm946.S
  dmaengine: PL08x: Fix trivial build error
  ARM: Fix build error for SMP=n builds

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Really fix build without CONFIG_PCI
  powerpc: Fix build without CONFIG_PCI
  powerpc/4xx: Fix build of PCI code on 405
  powerpc/pseries: Simplify vpa deregistration functions
  powerpc/pseries: Cleanup VPA registration and deregistration errors
  powerpc/pseries: Fix kexec on recent firmware versions
  MAINTAINERS: change maintainership of mpc5xxx
  powerpc: Make KVM_GUEST default to n
  powerpc/kvm: Fix build errors with older toolchains
  powerpc: Lack of ibm,io-events not that important!
  powerpc: Move kdump default base address to half RMO size on 64bit
  powerpc/perf: Disable pagefaults during callchain stack read
  ppc: Remove duplicate definition of PV_POWER7
  powerpc: pseries: Fix kexec on machines with more than 4TB of RAM
  powerpc: Jump label misalignment causes oops at boot
  powerpc: Clean up some panic messages in prom_init
  powerpc: Fix device tree claim code
  powerpc: Return the_cpu_ spec from identify_cpu
  powerpc: mtspr/mtmsr should take an unsigned long

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  Ecryptfs: Add mount option to check uid of device being mounted = expect uid
  eCryptfs: Fix payload_len unitialized variable warning
  eCryptfs: fix compile error
  eCryptfs: Return error when lower file pointer is NULL

Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This has now been well tested, and several platforms are now selecting
this directly.  It's time to drop its experimental status.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'perf/core' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Close a TOCTOU race for mounts done via ecryptfs-mount-private.  The mount
source (device) can be raced when the ownership test is done in userspace.
Provide Ecryptfs a means to force the uid check at mount time.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>

syslog-ng versions before 3.3.0beta1 (2011-05-12) assume that
CAP_SYS_ADMIN is sufficient to access syslog, so ever since CAP_SYSLOG
was introduced (2010-11-25) they have triggered a warning.

Commit ee24aebf ("cap_syslog: accept CAP_SYS_ADMIN for now")
improved matters a little by making syslog-ng work again, just keeping
the WARN_ONCE().  But still, this is a warning that writes a stack trace
we don't care about to syslog, sets a taint flag, and alarms sysadmins
when nothing worse has happened than use of an old userspace with a
recent kernel.

Convert the WARN_ONCE to a printk_once to avoid that while continuing to
give userspace developers a hint that this is an unwanted
backward-compatibility feature and won't be around forever.
Reported-by: Ralf Hildebrandt <ralf.hildebrandt@charite.de>
Reported-by: Niels <zorglub_olsen@hotmail.com>
Reported-by: Paweł Sikora <pluto@agmk.net>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Liked-by: Gergely Nagy <algernon@madhouse-project.org>
Acked-by: Serge Hallyn <serge@hallyn.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 8521fc50.

The patch incorrectly assumes that using atomic FLUSHING_CACHED_CHARGE
bit operations is sufficient but that is not true.  Johannes Weiner has
reported a crash during parallel memory cgroup removal:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
  IP: [<ffffffff81083b70>] css_is_ancestor+0x20/0x70
  Oops: 0000 [#1] PREEMPT SMP
  Pid: 19677, comm: rmdir Tainted: G        W   3.0.0-mm1-00188-gf38d32b #35 ECS MCP61M-M3/MCP61M-M3
  RIP: 0010:[<ffffffff81083b70>]  css_is_ancestor+0x20/0x70
  RSP: 0018:ffff880077b09c88  EFLAGS: 00010202
  Process rmdir (pid: 19677, threadinfo ffff880077b08000, task ffff8800781bb310)
  Call Trace:
   [<ffffffff810feba3>] mem_cgroup_same_or_subtree+0x33/0x40
   [<ffffffff810feccf>] drain_all_stock+0x11f/0x170
   [<ffffffff81103211>] mem_cgroup_force_empty+0x231/0x6d0
   [<ffffffff811036c4>] mem_cgroup_pre_destroy+0x14/0x20
   [<ffffffff81080559>] cgroup_rmdir+0xb9/0x500
   [<ffffffff81114d26>] vfs_rmdir+0x86/0xe0
   [<ffffffff81114e7b>] do_rmdir+0xfb/0x110
   [<ffffffff81114ea6>] sys_rmdir+0x16/0x20
   [<ffffffff8154d76b>] system_call_fastpath+0x16/0x1b

We are crashing because we try to dereference cached memcg when we are
checking whether we should wait for draining on the cache.  The cache is
already cleaned up, though.

There is also a theoretical chance that the cached memcg gets freed
between we test for the FLUSHING_CACHED_CHARGE and dereference it in
mem_cgroup_same_or_subtree:

        CPU0                    CPU1                         CPU2
  mem=stock->cached
  stock->cached=NULL
                              clear_bit
                                                        test_and_set_bit
  test_bit()                    ...
  <preempted>             mem_cgroup_destroy
  use after free

The percpu_charge_mutex protected from this race because sync draining
is exclusive.

It is safer to revert now and come up with a more parallel
implementation later.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: Fix partial count comparison confusion

fs/ecryptfs/keystore.c: In function ‘ecryptfs_generate_key_packet_set’:
fs/ecryptfs/keystore.c:1991:28: warning: ‘payload_len’ may be used uninitialized in this function [-Wuninitialized]
fs/ecryptfs/keystore.c:1976:9: note: ‘payload_len’ was declared here
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>

This patch fixes the compile error reported at the address:

https://bugzilla.kernel.org/show_bug.cgi?id=40292

The problem arises when compiling eCryptfs as built-in and the 'encrypted'
key type as a module. The patch prevents this combination from being set in
the kernel configuration, by fixing the eCryptfs dependencies.
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Reported-by: David Hill <hilld@binarystorm.net>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>

When an eCryptfs inode's lower file has been closed, and the pointer has
been set to NULL, return an error when trying to do a lower read or
write rather than calling BUG().

https://bugzilla.kernel.org/show_bug.cgi?id=37292Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: <stable@kernel.org>

The external symbol files are generated by JIT compilers, for example, but we
need to make sure they're ours before injecting them to 'perf report'.
Requested-by: Ingo Molnar <mingo@elte.hu>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1312919658-17158-1-git-send-email-penberg@kernel.orgSigned-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

deactivate_slab() has the comparison if more than the minimum number of
partial pages are in the partial list wrong. An effect of this may be that
empty pages are not freed from deactivate_slab(). The result could be an
OOM due to growth of the partial slabs per node. Frees mostly occur from
__slab_free which is okay so this would only affect use cases where a lot
of switching around of per cpu slabs occur.

Switching per cpu slabs occurs with high frequency if debugging options are
enabled.
Reported-and-tested-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>

The 'perf sched' command usage still showing 'trace' command instead of
the 'script' command.

Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110809124651.GD2056@jolsa.brq.redhat.comSigned-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The session object is released prematurely when processing events for
latency command. The session's thread objects are used within the
output_lat_thread function.

Runnning following commands:

 # perf sched record
 # perf sched latency

the latter displays incorrect data and might cause access violation.

Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1312837414-3819-1-git-send-email-jolsa@redhat.comSigned-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: fix check_bytes() for slub debugging
  slub: Fix full list corruption if debugging is on

Just like we do already for perf.data files.
Requested-by: Ingo Molnar <mingo@elte.hu>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Christian Ohm <chr.ohm@gmx.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-qgokmxsmvppwpc5404qhyk7e@git.kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: pss - don't use the deprecated function check_region
  ALSA: timer - Add NULL-check for invalid slave timer
  ALSA: timer - Fix Oops at closing slave timer
  ASoC: Acknowledge WM8996 interrupts before acting on them
  ASoC: Rename WM8915 to WM8996
  ALSA: Fix dependency of CONFIG_SND_TEA575X
  ALSA: asihpi - use kzalloc()
  ALSA: snd-usb-caiaq: Fix keymap for RigKontrol3
  ALSA: snd-usb: Fix uninitialized variable usage
  ALSA: hda - Fix a complile warning in patch_via.c
  ALSA: hdspm - Fix uninitialized compile warnings
  ALSA: usb-audio - add quirk for Keith McMillen StringPort
  ALSA: snd-usb: operate on given mixer interface only
  ALSA: snd-usb: avoid dividing by zero on invalid input
  ALSA: snd-usb: Accept UAC2 FORMAT_TYPE descriptors with bLength > 6
  sound: oss/pas2: Remove CLOCK_TICK_RATE dependency from PAS16 driver
  ALSA: hda - Use auto-parser for ASUS UX50, Eee PC P901, S101 and P1005
  ALSA: hda - Fix digital-mic mono recording on ASUS Eee PC
  ASoC: sgtl5000: fix cache handling
  ASoC: Disable wm_hubs periodic DC servo update

The private object support has migrated from gma500 into the DRM core,
remove our now clashing copy.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'perf/core' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

The check_bytes() function is used by slub debugging.  It returns a pointer
to the first unmatching byte for a character in the given memory area.

If the character for matching byte is greater than 0x80, check_bytes()
doesn't work.  Becuase 64-bit pattern is generated as below.

	value64 = value | value << 8 | value << 16 | value << 24;
	value64 = value64 | value64 << 32;

The integer promotions are performed and sign-extended as the type of value
is u8.  The upper 32 bits of value64 is 0xffffffff in the first line, and
the second line has no effect.

This fixes the 64-bit pattern generation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>

When a slab is freed by __slab_free() and the slab can only contain a
single object ever then it was full (and therefore not on the partial
lists but on the full list in the debug case) before we reached
slab_empty.

This caused the following full list corruption when SLUB debugging was enabled:

  [ 5913.233035] ------------[ cut here ]------------
  [ 5913.233097] WARNING: at lib/list_debug.c:53 __list_del_entry+0x8d/0x98()
  [ 5913.233101] Hardware name: Adamo 13
  [ 5913.233105] list_del corruption. prev->next should be ffffea000434fd20, but was ffffea0004199520
  [ 5913.233108] Modules linked in: nfs fscache fuse ebtable_nat ebtables ppdev parport_pc lp parport ipt_MASQUERADE iptable_nat nf_nat nfsd lockd nfs_acl auth_rpcgss xt_CHECKSUM sunrpc iptable_mangle bridge stp llc cpufreq_ondemand acpi_cpufreq freq_table mperf ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables rfcomm bnep arc4 iwlagn snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_intel btusb mac80211 snd_hda_codec bluetooth snd_hwdep snd_seq snd_seq_device snd_pcm usb_debug dell_wmi sparse_keymap cdc_ether usbnet cdc_acm uvcvideo cdc_wdm mii cfg80211 snd_timer dell_laptop videodev dcdbas snd microcode v4l2_compat_ioctl32 soundcore joydev tg3 pcspkr snd_page_alloc iTCO_wdt i2c_i801 rfkill iTCO_vendor_support wmi virtio_net kvm_intel kvm ipv6 xts gf128mul dm_crypt i915 drm_kms_helper drm i2c_algo_bit i2c_core video [last unloaded: scsi_wait_scan]
  [ 5913.233213] Pid: 0, comm: swapper Not tainted 3.0.0+ #127
  [ 5913.233213] Call Trace:
  [ 5913.233213]  <IRQ>  [<ffffffff8105df18>] warn_slowpath_common+0x83/0x9b
  [ 5913.233213]  [<ffffffff8105dfd3>] warn_slowpath_fmt+0x46/0x48
  [ 5913.233213]  [<ffffffff8127e7c1>] __list_del_entry+0x8d/0x98
  [ 5913.233213]  [<ffffffff8127e7da>] list_del+0xe/0x2d
  [ 5913.233213]  [<ffffffff814e0430>] __slab_free+0x1db/0x235
  [ 5913.233213]  [<ffffffff811706ab>] ? bvec_free_bs+0x35/0x37
  [ 5913.233213]  [<ffffffff811706ab>] ? bvec_free_bs+0x35/0x37
  [ 5913.233213]  [<ffffffff811706ab>] ? bvec_free_bs+0x35/0x37
  [ 5913.233213]  [<ffffffff81133085>] kmem_cache_free+0x88/0x102
  [ 5913.233213]  [<ffffffff811706ab>] bvec_free_bs+0x35/0x37
  [ 5913.233213]  [<ffffffff811706e1>] bio_free+0x34/0x64
  [ 5913.233213]  [<ffffffff813dc390>] dm_bio_destructor+0x12/0x14
  [ 5913.233213]  [<ffffffff8116fef6>] bio_put+0x2b/0x2d
  [ 5913.233213]  [<ffffffff813dccab>] clone_endio+0x9e/0xb4
  [ 5913.233213]  [<ffffffff8116f7dd>] bio_endio+0x2d/0x2f
  [ 5913.233213]  [<ffffffffa00148da>] crypt_dec_pending+0x5c/0x8b [dm_crypt]
  [ 5913.233213]  [<ffffffffa00150a9>] crypt_endio+0x78/0x81 [dm_crypt]

[ Full discussion here: https://lkml.org/lkml/2011/8/4/375 ]

Make sure that we remove such a slab also from the full lists.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Reported-and-tested-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>

Add support to Romely-EP SandyBridge.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1312264895-2010-1-git-send-email-youquan.song@intel.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.

POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:

  * si_signo = SIGBUS
  * si_code = BUS_ADRALN
  * si_addr = misaligned data address at which access was attempted
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.

In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.

This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.

Prior to ARMv6, the behaviour is unchanged.

For ARMv6 and above, the behaviour changes as follows:

  * Attempting to ignore faults on ARMv6 results in the mode being
    forced to UM_FIXUP instead.  A warning is printed if this
    happened as a result of a write to /proc/cpu/alignment.  The
    user's UM_WARN bit (if present) is still honoured.

  * An alignment= argument from the kernel command-line is now
    honoured, except that the kernel will modify the specified mode
    as described above.  This is allows modes such as UM_SIGNAL and
    UM_WARN to be active immediately from boot, which is useful for
    debugging purposes.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

poison_init_mem() used a loop of:

	while ((count = count - 4))

which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much.  On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>