- 10 Apr, 2019 7 commits
-
-
Ido Schimmel authored
In Spectrum-1, when a multicast packet is admitted to the shared buffer it increases the quotas of all the ports and {port, TC} to which it is forwarded to. The above means that multicast packets are accounted multiple times in the shared buffer and can therefore cause the associated shared buffer pool to fill up very quickly. To work around this issue, commit e83c045e ("mlxsw: spectrum_buffers: Configure MC pool") added a dedicated multicast pool in which multicast packets are accounted. The issue is not present in Spectrum-2, but in order to be backward compatible with Spectrum-1, its default behavior is to allow a multicast packet to increase multiple egress quotas instead of one. Until the new (non-backward compatible) mode is supported, configure a dedicated multicast pool as in Spectrum-1. Fixes: fe099bf6 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration") Signed-off-by:Ido Schimmel <idosch@mellanox.com> Reviewed-by:
Petr Machata <petrm@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Test that it is possible to set an IP address on a VRF and that it is not vetoed. Signed-off-by:
-
Ido Schimmel authored
Commit 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") enabled the driver to veto router interface (RIF) MAC addresses that it cannot support. This check should only be performed for interfaces for which the driver actually configures a RIF. A VRF upper is not one of them, so ignore it. Without this patch it is not possible to set an IP address on the VRF device and use it as a loopback. Fixes: 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by:
Alexander Petrovskiy <alexpe@mellanox.com> Tested-by:
-
Ido Schimmel authored
The workqueue is used to periodically update the networking stack about activity / statistics of various objects such as neighbours and TC actions. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. Fixes: 3d5479e9 ("mlxsw: core: Remove deprecated create_workqueue") Signed-off-by:
-
Ido Schimmel authored
The ordered workqueue is used to offload various objects such as routes and neighbours in the order they are notified. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker tries to flush a non-WQ_MEM_RECLAIM workqueue. [1] [97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker [97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130 ... [97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] [97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130 ... [97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086 [97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000 [97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046 [97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0 [97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0 [97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0 [97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000 [97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0 [97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [97703.543115] Call Trace: [97703.543129] __flush_work+0xbd/0x1e0 [97703.543137] ? __cancel_work_timer+0x136/0x1b0 [97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0 [97703.543154] __cancel_work_timer+0x136/0x1b0 [97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core] [97703.543184] cancel_work_sync+0x10/0x20 [97703.543191] rhashtable_free_and_destroy+0x23/0x140 [97703.543198] rhashtable_destroy+0xd/0x10 [97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum] [97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum] [97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum] [97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum] [97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum] [97703.543484] process_one_work+0x1fd/0x400 [97703.543493] worker_thread+0x34/0x410 [97703.543500] kthread+0x121/0x140 [97703.543507] ? process_one_work+0x400/0x400 [97703.543512] ? kthread_park+0x90/0x90 [97703.543523] ret_from_fork+0x35/0x40 Fixes: a3832b31 ("mlxsw: core: Create an ordered workqueue for FIB offload") Signed-off-by:
Semion Lisyansky <semionl@mellanox.com> Acked-by:
-
Ido Schimmel authored
The EMAD workqueue is used to handle retransmission of EMAD packets that contain configuration data for the device's firmware. Given the workers need to allocate these packets and that the code is not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM flag. Fixes: d965465b ("mlxsw: core: Fix possible deadlock") Signed-off-by:
-
Ido Schimmel authored
The driver cannot guarantee in the prepare phase that it will be able to write an MDB entry to the device. In case the driver returned success during the prepare phase, but then failed to add the entry in the commit phase, a WARNING [1] will be generated by the switchdev core. Fix this by doing the work in the prepare phase instead. [1] [ 358.544486] swp12s0: Commit of object (id=2) failed. [ 358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0 [ 358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350 [ 358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016 [ 358.580582] Workqueue: events switchdev_deferred_process_work [ 358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0 ... [ 358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286 [ 358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000 [ 358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8 [ 358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000 [ 358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000 [ 358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200 [ 358.659790] FS: 0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000 [ 358.668820] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0 [ 358.683188] Call Trace: [ 358.685918] switchdev_port_obj_add_deferred+0x13/0x60 [ 358.691655] switchdev_deferred_process+0x6b/0xf0 [ 358.696907] switchdev_deferred_process_work+0xa/0x10 [ 358.702548] process_one_work+0x1f5/0x3f0 [ 358.707022] worker_thread+0x28/0x3c0 [ 358.711099] ? process_one_work+0x3f0/0x3f0 [ 358.715768] kthread+0x10d/0x130 [ 358.719369] ? __kthread_create_on_node+0x180/0x180 [ 358.724815] ret_from_fork+0x35/0x40 Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support") Signed-off-by:
Alex Kushnarov <alexanderk@mellanox.com> Tested-by:
-
- 09 Apr, 2019 5 commits
-
-
David S. Miller authored
Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Various fixes: * iTXQ fixes from Felix * tracing fix - increase message length * fix SW_CRYPTO_CONTROL enforcement * WMM rule handling for regdomain intersection * max_interfaces in hwsim - reported by syzbot * clear private data in some more commands * a clang compiler warning fix I added a patch with two new (unused) macros for rate-limited printing to simplify getting the users into the tree. ==================== Signed-off-by:
-
Alexander Wetzel authored
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast keys, the original override was intended to be done for group keys as those are treated specially by mac80211 and would always have been rejected. Now the situation is that AP_VLAN support must be enabled by the driver if it can support it (meaning it can support software crypto GTK TX). Thus, also simplify the code - if we get here with AP_VLAN and non- pairwise key, software crypto must be used (driver doesn't know about the interface) and can be used (driver must've advertised AP_VLAN if it also uses SW_CRYPTO_CONTROL). Fixes: db3bdcb9 ("mac80211: allow AP_VLAN operation on crypto controlled devices") Signed-off-by:
Alexander Wetzel <alexander@wetzel-home.de> [rewrite commit message] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Off by one and bounds checking fixes in NFC, from Dan Carpenter. 2) There have been many weird regressions in r8169 since we turned ASPM support on, some are still not understood nor completely resolved. Let's turn this back off for now. From Heiner Kallweit. 3) Signess fixes for ethtool speed value handling, from Michael Zhivich. 4) Handle timestamps properly in macb driver, from Paul Thomas. 5) Two erspan fixes, it's the usual "skb ->data potentially reallocated and we're holding a stale protocol header pointer". From Lorenzo Bianconi. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: bnxt_en: Reset device on RX buffer errors. bnxt_en: Improve RX consumer index validity check. net: macb driver, check for SKBTX_HW_TSTAMP qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant ethtool: avoid signed-unsigned comparison in ethtool_validate_speed() net: ip6_gre: fix possible use-after-free in ip6erspan_rcv net: ip_gre: fix possible use-after-free in erspan_rcv r8169: disable ASPM again MAINTAINERS: ieee802154: update documentation file pattern net: vrf: Fix ping failed when vrf mtu is set to 0 selftests: add a tc matchall test case nfc: nci: Potential off by one in ->pipes[] array NFC: nci: Add some bounds checking in nci_hci_cmd_received() -
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-securityLinus Torvalds authored
Pull TPM fixes from James Morris: "From Jarkko: These are critical fixes for v5.1. Contains also couple of new selftests for v5.1 features (partial reads in /dev/tpm0)" * 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: selftests/tpm2: Open tpm dev in unbuffered mode selftests/tpm2: Extend tests to cover partial reads KEYS: trusted: fix -Wvarags warning tpm: Fix the type of the return value in calc_tpm2_event_size() KEYS: trusted: allow trusted.ko to initialize w/o a TPM tpm: fix an invalid condition in tpm_common_poll tpm: turn on TPM on suspend for TPM 1.x
-
git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds authored
Pull xtensa fixes from Max Filippov: - fix syscall number passed to trace_sys_exit - fix syscall number initialization in start_thread - fix level interpretation in the return_address - fix format string warning in init_pmd * tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: fix format string warning in init_pmd xtensa: fix return_address xtensa: fix initialization of pt_regs::syscall in start_thread xtensa: use actual syscall number in do_syscall_trace_leave
-
- 08 Apr, 2019 28 commits
-
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: 2 bug fixes. The first patch prevents possible driver crash if we get a bad RX index from the hardware. The second patch resets the device when the hardware reports buffer error to recover from the error. Please queue these for -stable also. Thanks. ==================== Signed-off-by: -
Michael Chan authored
If the RX completion indicates RX buffers errors, the RX ring will be disabled by firmware and no packets will be received on that ring from that point on. Recover by resetting the device. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
There is logic to check that the RX/TPA consumer index is the expected index to work around a hardware problem. However, the potentially bad consumer index is first used to index into an array to reference an entry. This can potentially crash if the bad consumer index is beyond legal range. Improve the logic to use the consumer index for dereferencing after the validity check and log an error message. Fixes: fa7e2812 ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)") Signed-off-by:
-
Paul Thomas authored
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been enabled for this skb. It does fix the issue where normal socks that aren't expecting a timestamp will not wake up on select, but when a user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work. Signed-off-by:
Paul Thomas <pthomas8589@gmail.com> Signed-off-by:
-
David S. Miller authored
Michael Zhivich says: ==================== ethtool: fix use of SPEED_UNKNOWN constant This patch series addresses 2 related issues: 1. ethtool_validate_speed() triggers a "signed-unsigned comparison" warning due to type difference of SPEED_UNKNOWN constant (int) and argument to ethtool_validate_speed (__u32). 2. some drivers use u16 storage for SPEED_UNKNOWN constant, resulting in value truncation and thus failure to test against SPEED_UNKNOWN correctly. This revised series addresses several feedback comments: - split up the patch in to series - do not unnecessarily change drivers that use "int" storage for speed values ==================== Signed-off-by: -
Michael Zhivich authored
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant, which is defined as -1, resulting in value truncation and thus incorrect test results against SPEED_UNKNOWN. For example, the following test will print "False": u16 speed = SPEED_UNKNOWN; if (speed == SPEED_UNKNOWN) printf("True"); else printf("False"); Change storage of speed to use u32 to avoid this issue. Signed-off-by:Michael Zhivich <mzhivich@akamai.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Michael Zhivich authored
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant, which is defined as -1, resulting in value truncation and thus incorrect test results against SPEED_UNKNOWN. For example, the following test will print "False": u16 speed = SPEED_UNKNOWN; if (speed == SPEED_UNKNOWN) printf("True"); else printf("False"); Change storage of speed to use u32 to avoid this issue. Signed-off-by: -
Michael Zhivich authored
When building C++ userspace code that includes ethtool.h with "-Werror -Wall", g++ complains about signed-unsigned comparison in ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1. Explicitly cast SPEED_UNKNOWN to __u32 to match type of ethtool_validate_speed() argument. Signed-off-by:
-
David S. Miller authored
Lorenzo Bianconi says: ==================== fix possible use-after-free in erspan_v{4,6} Similar to what I did in commit bb9bd814 ("ipv6: sit: reset ip header pointer in ipip6_rcv"), fix possible use-after-free in erspan_rcv and ip6erspan_rcv extracting tunnel metadata since the packet can be 'uncloned' running __iptunnel_pull_header ==================== Signed-off-by: -
Lorenzo Bianconi authored
erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove erspan header. This can determine a possible use-after-free accessing pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned' running pskb_expand_head if it is a cloned gso skb (e.g if the packet has been sent though a veth device). Fix it resetting pkt_md pointer after __iptunnel_pull_header Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
-
Lorenzo Bianconi authored
erspan tunnels run __iptunnel_pull_header on received skbs to remove gre and erspan headers. This can determine a possible use-after-free accessing pkt_md pointer in erspan_rcv since the packet will be 'uncloned' running pskb_expand_head if it is a cloned gso skb (e.g if the packet has been sent though a veth device). Fix it resetting pkt_md pointer after __iptunnel_pull_header Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code") Signed-off-by:
-
Tadeusz Struk authored
In order to have control over how many bytes are read or written the device needs to be opened in unbuffered mode. Signed-off-by:
Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by:
James Morris <james.morris@microsoft.com>
-
Tadeusz Struk authored
Three new tests added: 1. Send get random cmd, read header in 1st read, read the rest in second read - expect success 2. Send get random cmd, read only part of the response, send another get random command, read the response - expect success 3. Send get random cmd followed by another get random cmd, without reading the first response - expect the second cmd to fail with -EBUSY Signed-off-by:
-
ndesaulniers@google.com authored
Fixes the warning reported by Clang: security/keys/trusted.c:146:17: warning: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Wvarargs] va_start(argp, h3); ^ security/keys/trusted.c:126:37: note: parameter of type 'unsigned char' is declared here unsigned char *h2, unsigned char h3, ...) ^ Specifically, it seems that both the C90 (4.8.1.1) and C11 (7.16.1.4) standards explicitly call this out as undefined behavior: The parameter parmN is the identifier of the rightmost parameter in the variable parameter list in the function definition (the one just before the ...). If the parameter parmN is declared with ... or with a type that is not compatible with the type that results after application of the default argument promotions, the behavior is undefined. Link: https://github.com/ClangBuiltLinux/linux/issues/41 Link: https://www.eskimo.com/~scs/cclass/int/sx11c.htmlSuggested-by:David Laight <David.Laight@aculab.com> Suggested-by:
Denis Kenzior <denkenz@gmail.com> Suggested-by:
James Bottomley <jejb@linux.vnet.ibm.com> Suggested-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
-
Yue Haibing authored
calc_tpm2_event_size() has an invalid signature because it returns a 'size_t' where as its signature says that it returns 'int'. Cc: <stable@vger.kernel.org> Fixes: 4d23cc32 ("tpm: add securityfs support for TPM 2.0 firmware event log") Suggested-by:
Yue Haibing <yuehaibing@huawei.com> Reviewed-by:
-
Jarkko Sakkinen authored
Allow trusted.ko to initialize w/o a TPM. This commit also adds checks to the exported functions to fail when a TPM is not available. Fixes: 24073043 ("KEYS: trusted: explicitly use tpm_chip structure...") Cc: James Morris <jmorris@namei.org> Reported-by:
Dan Williams <dan.j.williams@intel.com> Tested-by:
-
Tadeusz Struk authored
The poll condition should only check response_length, because reads should only be issued if there is data to read. The response_read flag only prevents double writes. The problem was that the write set the response_read to false, enqued a tpm job, and returned. Then application called poll which checked the response_read flag and returned EPOLLIN. Then the application called read, but got nothing. After all that the async_work kicked in. Added also mutex_lock around the poll check to prevent other possible race conditions. Fixes: 9488585b ("tpm: add support for partial reads") Reported-by:
Mantas Mikulėnas <grawity@gmail.com> Tested-by:
-
Jarkko Sakkinen authored
tpm_chip_start/stop() should be also called for TPM 1.x devices on suspend. Add that functionality back. Do not lock the chip because it is unnecessary as there are no multiple threads using it when doing the suspend. Fixes: a3fbfae8 ("tpm: take TPM chip power gating out of tpm_transmit()") Reported-by:
Paul Zimmerman <pauldzim@gmail.com> Signed-off-by:
Domenico Andreoli <domenico.andreoli@linux.com> Signed-off-by:
-
Heiner Kallweit authored
There's a significant number of reports that re-enabling ASPM causes different issues, ranging from decreased performance to system not booting at all. This affects only a minority of users, but the number of affected users is big enough that we better switch off ASPM again. This will hurt notebook users who are not affected by the issues, they may see decreased battery runtime w/o ASPM. With the PCI core folks is being discussed to add generic sysfs attributes to control ASPM. Once this is in place brave enough users can re-enable ASPM on their system. Fixes: a99790bf ("r8169: Reinstate ASPM Support") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Stefan Schmidt authored
When moving the documentation for the ieee802154 subsystem from plain text to rst the file pattern in the MAINTAINERS file got wrong. Updating it here to fix scripts using this file. Reported-by:
Joe Perches <joe@perches.com> Signed-off-by:
Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by:
-
Felix Fietkau authored
Currently there is no way for the driver to signal to mac80211 that it should schedule a TXQ even if there are no packets on the mac80211 part of that queue. This is problematic if the driver has an internal retry queue to deal with software A-MPDU retry. This patch changes the behavior of ieee80211_schedule_txq to always schedule the queue, as its only user (ath9k) seems to expect such behavior already: it calls this function on tx status and on powersave wakeup whenever its internal retry queue is not empty. Also add an extra argument to ieee80211_return_txq to get the same behavior. This fixes an issue on ath9k where tx queues with packets to retry (and no new packets in mac80211) would not get serviced. Fixes: 89cea749 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs") Signed-off-by:
Felix Fietkau <nbd@nbd.name> Acked-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Johannes Berg authored
If we just set this to 2048, and have multiple limits you can select from, the total number might run over and cause a warning in cfg80211. This doesn't make sense, so we just calculate the total max_interfaces now. Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com Fixes: 99e3a44b ("mac80211_hwsim: allow setting iftype support") Signed-off-by:
-
Stanislaw Gruszka authored
wiphy_{err,warn}_ratelimited will be used by rt2x00 Signed-off-by:Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fix from Herbert Xu: "This fixes a bug in the implementation of xcbc and cmac in caam" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: caam - fix copy of next buffer for xcbc and cmac
-
Miaohe Lin authored
When the mtu of a vrf device is set to 0, it would cause ping failed. So I think we should limit vrf mtu in a reasonable range to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it will works for both ipv4 and ipv6. And if dev->max_mtu still be 0 can be confusing, so I set dev->max_mtu to ETH_MAX_MTU. Here is the reproduce step: 1.Config vrf interface and set mtu to 0: 3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master vrf1 state UP mode DEFAULT group default qlen 1000 link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff 2.Ping peer: 3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master vrf1 state UP group default qlen 1000 link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff inet 10.0.0.1/16 scope global enp4s0 valid_lft forever preferred_lft forever connect: Network is unreachable 3.Set mtu to default value, ping works: PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data. 64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms Fixes: ad49bc63 ("net: vrf: remove MTU limits for vrf device") Signed-off-by:Miaohe Lin <linmiaohe@huawei.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Qian Cai authored
The commit 510ded33 ("slab: implement slab_root_caches list") changes the name of the list node within "struct kmem_cache" from "list" to "root_caches_node", but leaks_show() still use the "list" which causes a crash when reading /proc/slab_allocators. You need to have CONFIG_SLAB=y and CONFIG_MEMCG=y to see the problem, because without MEMCG all slab caches are root caches, and the "list" node happens to be the right one. Fixes: 510ded33 ("slab: implement slab_root_caches list") Signed-off-by:
Qian Cai <cai@lca.pw> Reviewed-by:
Tobin C. Harding <tobin@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Nicolas Dichtel authored
This is a follow up of the commit 0db6f8be ("net/sched: fix ->get helper of the matchall cls"). To test it: $ cd tools/testing/selftests/tc-testing $ ln -s ../plugin-lib/nsPlugin.py plugins/20-nsPlugin.py $ ./tdc.py -n -e 2638 Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Linus Torvalds authored
-
