In XLP9XX, the interrupt routing table for MSI-X has been moved to the
PCIe controller's config space from PIC. There are also 32 MSI-X
interrupts available per link on XLP9XX.

Update XLP MSI/MSI-X code to handle this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6912/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add support for the XLP5XX processor which is an 8 core variant of the
XLP9XX. Add XLP5XX cases to code which earlier handled XLP9XX.
Signed-off-by: Yonghong Song <ysong@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6871/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Calculate XLP 9XX and 2XX core frequency from the per-core PLL. This
should give the correct value for all board configurations.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6870/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Update PIC frequency calculation for XLP9XX and 2XX processors using
the correct PLL registers. This should work for all possible board
configurations.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6876/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add the compatible property to the PIC entry. Also fix up the nodename
to use the correct address.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6869/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use PRID_IMP_MASK macro instead of 0xff00 to extract the processor
type.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6868/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add IRQ to IRT (PIC interupt table index) mapping for SATA, GPIO, NAND
and SPI interfaces on the XLP SoC. Fix offsets for few blocks and add
device IDs for a few blocks.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6911/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The ELPA bit needs to be set in the PAGEGRAIN register to enable
access to >64GB physical address. Update reset.S to do this from
every hardware thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6866/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Update thread wakeup function to use scratch registers for saving SP and
RA. Move the register restore code needed for thread 0 to the calling
function. This reduces the size of code copied to the reset vector.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6910/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use standard function to print cpumask. Also fixup a typo in the same
file.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6909/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Warn and return if invalid IRQ is passed to nlm_set_pic_extra_ack.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6862/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is needed for nlm_node_present(0) to work on uniprocessor compile.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6861/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The macros in topology.h need CONFIG_SMP, and the uniprocessor compilation
fails due to this. Wrap the macros in an ifdef so that uniprocessor works.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6863/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This is needed for two node XLP9xx configurations.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6860/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6743/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This adds initial support for BPF-JIT on MIPS

Tested on mips32 LE/BE and mips64 BE/n64 using
dhcp, ping and various tcpdump filters.

Benchmarking:

Assuming the remote MIPS target uses 192.168.154.181
as its IP address, and the local host uses 192.168.154.136,
the following results can be obtained using the following
tcpdump filter (catches no frames) and a simple
'time ping -f -c 1000000' command.

[root@(none) ~]# tcpdump -p -n -s 0 -i eth0 net 10.0.0.0/24 -d
(000) ldh      [12]
(001) jeq      #0x800           jt 2	jf 8
(002) ld       [26]
(003) and      #0xffffff00
(004) jeq      #0xa000000       jt 16	jf 5
(005) ld       [30]
(006) and      #0xffffff00
(007) jeq      #0xa000000       jt 16	jf 17
(008) jeq      #0x806           jt 10	jf 9
(009) jeq      #0x8035          jt 10	jf 17
(010) ld       [28]
(011) and      #0xffffff00
(012) jeq      #0xa000000       jt 16	jf 13
(013) ld       [38]
(014) and      #0xffffff00
(015) jeq      #0xa000000       jt 16	jf 17
(016) ret      #65535

- BPF-JIT Disabled

real    1m38.005s
user    0m1.510s
sys     0m6.710s

- BPF-JIT Enabled

real    1m35.215s
user    0m1.200s
sys     0m4.140s

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6736/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6733/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6732/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6731/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6730/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6729/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6728/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6727/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Fixed conflict due to other preceeding conflicts.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6726/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit

[ralf@linux-mips.org: Fixed conflict with
49e9529b [MIPS: uasm: add jalr instruction].
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6725/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later one for the jalr and wsbh instructions.

[ralf@linux-mips.org: Dropped arch/mips/include/asm/uasm.h segment because
that was already added by 49e9529b
[MIPS: uasm: add jalr instruction].
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6724/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by the sllv and srlv instructions.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6723/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.

[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add interface mode detection for Octeon II. This is necessary to detect
the interface modes correctly on the UBNT E200 board. Code is taken
from the UBNT GPL source release, with some alterations: SRIO, ILK and
RXAUI interface modes are removed and instead return disabled as these
modes are not currently supported.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Tested-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7039/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The CONFIG_MIPS_CPS SMP implementation should be able to handle all
cases the CONFIG_MIPS_CMP implementation does, but without requiring
bootloader assistance. It is also required in order to make use of
features such as hotplug & cpuidle core power gating. Enable it by
default for Malta configs that previously enabled the now deprecated
CONFIG_MIPS_CMP, and disable the latter. The local version suffix "cmp"
is removed rather than replaced with "cps" since there are other ways to
tell that the CPS SMP implementation is in use (the "VPE topology" line
in the boot log being one).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>

This patch adds a cpuidle driver for systems based around the MIPS
Coherent Processing System (CPS) architecture. It supports four idle
states:

  - The standard MIPS wait instruction.

  - The non-coherent wait, clock gated & power gated states exposed by
    the recently added pm-cps layer.

The pm-cps layer is used to enter all the deep idle states. Since cores
in the clock or power gated states cannot service interrupts, the
gic_send_ipi_single function is modified to send a power up command for
the appropriate core to the CPC in cases where the target CPU has marked
itself potentially incoherent.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>

Declaring this allows drivers which need to initialise each struct
cpuidle_device at initialisation time to make use of the structures
already defined in cpuidle.c, rather than having to wastefully define
their own.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>

This patch simply includes the cpuidle Kconfig entries in preparation
for cpuidle drivers used on MIPS systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>

Defines a macro intended to allow trivial use of the regular MIPS wait
instruction from cpuidle drivers, which may simply invoke the macro
within their array of states.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>

Rather than hardcoding CCA=0x5 for secondary cores, re-use the CCA from
the boot CPU. This allows overrides of the CCA using the cca= kernel
parameter to take effect on all CPUs for consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>