It's much simpler to just add one extra TRB chained to previous TRB to
handle ZLP. This helps us reduce pointless allocations and simplifies
the code a little bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Just like we did for all other endpoint types, let's rely on a chained
TRB pointing to ep0_bounce_addr in order to align transfer size. This
will make the code simpler.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of constantly recomputing how dwc and epnum relate to dep,
just pass dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If we pass TRB's own address on bpl/bph fields, we can get our SETUP
packet as immediate data on the TRB itself, without having to allocate
extra memory for it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There are several inconsistencies in the error handling code.
1. If clk_get() fails, it goes to clk_put().
2. If pdata->phy_init() fails, it does not disable u3d->clk.
3. In case of failure after stopping u3d, it does pdata->phy_deinit()
   and clk_disable(u3d->clk) twice.
4. It ignores failures in clk_enable().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Check fifo configuration values against device tree values for endpoint fifo
in auto configuration mode (fifo_mode=0).
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currently the of glue code in fsl-mph-dr-of will create the platform
device fsl-usb2-udc. As this driver should also be probed by this name,
this patch adds it to the devtypes list.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

That helper can be used from our tracepoint interface with very minor
edits. Let's do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In order to improve usability a tiny bit, we will return strings that
match what our tracepoints return.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of redecoding link state into a string, use our helper.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When writing, we expect the "otg" string. When showing, we return
"OTG". Let's downcase that word to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch splits the amd5536udc driver into two -- one that does
pci device registration and the other file that does the rest of
the driver tasks like the gadget/ep ops etc for Synopsys UDC.

This way of splitting helps in exporting core driver symbols which
can be used by any other platform/pci driver that is written for
the same Synopsys USB device controller.

The current patch also includes a change in the Kconfig and Makefile.
A new config option USB_SNP_CORE will be selected automatically when
any one of the platform or pci driver for the same UDC is selected.

Main changes:
- amd5536udc_pci.c: PCI device registration is moved to this file.

- amd5536udc.c:
  This file does rest of the core UDC fucntionality.
  9 symbols are exported so as to be used by amd5536udc_pci.c.
  Module parameter definitions are moved to header file.

- amd5536udc.h:
  Function declarations, module parameters definitions and few common
  header file includes are added to this file

- Kconfig:
  New USB_SNP_CORE option is added which will be auto selected when
  any pci or platform driver config option for the UDC is chosen.

- Makefile:
  Compiles the core and pci files separately.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for usb role swap via sysfs "role".

For example:
 1) Connect a usb cable using 2 Salvator-X boards.
  - For A-Device, the cable is connected to CN11 (USB3.0 ch0).
  - For B-Device, the cable is connected to CN9 (USB2.0 ch0).
 2) On A-Device, you input the following command:
  # echo peripheral > /sys/devices/platform/soc/ee020000.usb/role
 3) On B-Device, you input the following command:
  # echo host > /sys/devices/platform/soc/ee080200.usb-phy/role

Then, the A-Device acts as a peripheral and the B-Device acts as
a host. Please note that A-Device must input the following command
if you want the board to act as a host again.
 # echo host > /sys/devices/platform/soc/ee020000.usb/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Minor code cleanup based on feedback received on mailinglist.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds extcon support to see VBUS/ID signal states.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This usb 3.0 peripheral controller has a register (USB_OTG_STA) to monitor
the USB ID signal. So, this patch adds the ID signal monitoring to change
the mode to host (A-Host) or peripheral (B-Peripheral).
This patch also removes hardcoded setting as B-Peripheral mode.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If usb/otg-fsm.h and usb/composite.h are included together
then it results in the build warning [1].

Prevent that by defining VDBG locally.

Also get rid of MPC_LOC which doesn't seem to be used
by anyone.

[1] - warning fixed by this patch:

In file included from drivers/usb/dwc3/core.h:33,
   from drivers/usb/dwc3/ep0.c:33:
   include/linux/usb/otg-fsm.h:30:1: warning: "VDBG" redefined
   In file included from drivers/usb/dwc3/ep0.c:31:
   include/linux/usb/composite.h:615:1: warning: this is the location
   of the previous definition
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

To avoid checkpatch warnings with new patches let's
start using the BIT() macro wherever possible.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currently ffs_dev::name can be either allocated by the client of
the ffs_dev structure or by the f_fs.c core itself.  The former
is used by g_ffs while the latter happens with configfs.

Historically, g_ffs did not need to allocate separate buffer for
the name so what is now f_fs.c core never cared about freeing
that space.  With configfs the name needs to be copied since the
memory is not guaranteed to be availeble after ffs_set_inst_name
finishes.

The complication is therefore here to avoid allocations in the
g_ffs case but it complicates the code inproportinally to
benefits it provides.  In particular, g_ffs is considered
‘legacy’ so optimising for its sake is unlikely to be worth the
effort.

With that observation in mind, simplify the code by unifying the
code paths in g_ffs and configfs paths.  Furthermore, instead of
allocating a new buffer for the name, simply embed it in the
ffs_dev structure.  This further makes the memory management
less convoluted and error-prone.

The configfs interface for functionfs imposed a limit of 40
characters for the name so this results in a 41-byte buffer
added to the structure.  (For short names this may lead to
wasted memory but the actual amount is not immediately obvious
and depends on pointer size and which slab buckets the structure
and name would fall into).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

As of commit bb475230 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.

This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since the old common Samsung USB PHY code has been removed by commit ea2fdf84
("usb: phy: samsung: remove old common USB PHY code"), thus remove the unused
config.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This fixes the commit: 1cd8fd28 ("usb: gadget: dummy_hcd: add
SuperSpeed support").

In the case of ClearPortFeature and USB_PORT_FEAT_POWER, simply clear
the right bit regardless of what the wValue is.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: linux-usb@vger.kernel.org
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Unless HW sets quirk_ep_out_aligned_size, gadget driver shouldn't make
any efforts towards aligning transfers. If the UDC needs, it *must*
set the quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We have helpers for some of these, let's rely on them instead of open
coding what they do in u_ether.c
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

a %x is much easier for a human to parse when reading tracepoint
output. Let's change it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

As USB_CONFIGFS is not a part of the "USB Gadget Drivers" choice
anymore, the name for the option and its attached description needs to
be more descriptive. It appears one level higher in the configuration
menu, and without the context provided by the comments for the choice
entry, it needs to make sense on its own.

Conversely, the "USB Gadget Drivers" entry now only introduces the
legacy drivers, where one or more functions are combined in a single
driver. As the configfs option can be used as a full-fledged
alternative, rename the choice entry to show that it is not the only
way to provice service as an USB gadget.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

With commit bc49d1d1 ("usb: gadget: don't couple configfs to legacy
gadgets"),it is possible to build a modular kernel with both built-in
configfs support and modular legacy gadget drivers.

But when building a kernel without modules, it is also necessary to be
able to build with configfs but without any legacy gadget driver. This
was a possible configuration when the USB_CONFIGFS was a part of the
choice options, but not anymore.

Mark the choice for legacy gadget drivers as optional restores this.

Fixes: bc49d1d1 ("usb: gadget: don't couple configfs to legacy gadgets")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The gadget wants to set the starting microframe for the first ISOC TRB
to 4 microframes in the future, but it does so by multiplying the
dep->interval. This only works if dep->interval = 1. For other intervals
it will put it 4 *intervals* in the future which may be way too much.

Fix so that it always adds just one interval or at least 4 microframes.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Change goto labels to meaningful names from a series of errNs.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

A previous patch in the series reduces the number of  callsites of
dwc3_gadget_init_hw_endpoints from two to one. This patch removes the
redundant step of wrappering one function in the other, which can be done
by adding a parameter to dwc3_gadget_init_endpoints and moving the
linked-list initialization of dwc->gadet.ep_list.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

- DWC_USB3_NUM indicates the number of Device mode single directional
  endpoints, including OUT and IN endpoint 0.

- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
  endpoints active at any time, including control endpoint 0.

It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.

dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.

For example a from dwc3_core_num_eps() shows:
[    1.565000]  /usb0@f01d0000: found 8 IN and 0 OUT endpoints

This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.

The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We must make sure that our macros are safe against expressions passed
as arguments. We have seen one problem where GTXFIFOSIZ(n) was failing
when passed the expression (epnum >> 1) as argument. The problem was
caused by operator precedence between >> and *.

To make sure macros are safe, we just wrap argument with () when using
it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Remove unnecessary variable and update function prototype.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Rewrite udc_free_dma_chain() function to avoid use of pointer after free.

Addresses-Coverity-ID: 1091172
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.

Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.

So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.

With it, the gadget interface initializes properly on every
plug in.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The code was fixed in
commit 53642399 ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")
but the in-header documentation kept referencing 0 as the expected value.
Reference 1 instead as per original commit message.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add .gitignore file for untracked files in tools/usb.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Commit 76e0da34 ("usb-gadget/uvc: use per-attribute show and store
methods") caused a stringification of an undefined macro argument "aname",
so three UVC parameters (streaming_interval, streaming_maxpacket and
streaming_maxburst) were named "aname".

Add the definition of "aname" to the main macro and name the filenames as
originaly intended.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>