The function ip_rcv_finish() calls l3mdev_ip_rcv(). On any VRF except
the global VRF, this replaces skb->dev with the VRF master interface.
When calling ip_route_input_noref() from here, the checks for forwarding
look at this master device instead of the initial ingress interface.
This will allow packets to be routed which normally would be dropped.
For example, an interface that is not assigned an IP address should
drop packets, but because the checking is against the master device, the
packet will be forwarded.

The fix here is to still call l3mdev_ip_rcv(), but remember the initial
net_device. This is passed to the other functions within ip_rcv_finish,
so they still see the original interface.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

for preventing race conditions within ioctl calls.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add realization for mac address set and remove dummy callback.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to modules.alias:
alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are two batman-adv bugfix patches:

 - Fix reference counting for last_bonding_candidate, by Sven Eckelmann

 - Fix head room reservation for ELP packets, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If an error occurs in mlx4_init_eq_table the index used in the
err_out_unmap label is one too big which results in a panic in
mlx4_free_eq. This patch fixes the index in the error path.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A few more fixes:
 * better mesh path fixing, from Thomas
 * fix TIM IE recalculation after sending frames
   to a sleeping station, from Felix
 * fix sequence number assignment while sending
   frames to a sleeping station, also from Felix
 * validate number of probe response CSA counter
   offsets, fixing a copy/paste bug (from myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.

Cc: stable@vger.kernel.org
Fixes: 9a774c78 ("cfg80211: Support multiple CSA counters")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)'
will do nothing.

It is likely that 'if (!IS_ERR(pdata->clk))' was expected here.
In fact, the test can even be removed because 'clk_disable_unprepare'
already handles such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 4f008781 ("sctp: apply rhashtable api to send/recv
path"), sctp uses transport rhashtable with .obj_cmpfn sctp_hash_cmp,
in which it compares the members of the transport with the rhashtable
args to check if it's the right transport.

But sctp uses the transport without holding it in sctp_hash_cmp, it can
cause a use-after-free panic. As after it gets transport from hashtable,
another CPU may close the sk and free the asoc. In sctp_association_free,
it frees all the transports, meanwhile, the assoc's refcnt may be reduced
to 0, assoc can be destroyed by sctp_association_destroy.

So after that, transport->assoc is actually an unavailable memory address
in sctp_hash_cmp. Although sctp_hash_cmp is under rcu_read_lock, it still
can not avoid this, as assoc is not freed by RCU.

This patch is to hold the transport before checking it's members with
sctp_transport_hold, in which it checks the refcnt first, holds it if
it's not 0.

Fixes: 4f008781 ("sctp: apply rhashtable api to send/recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When system enters into kdump kernel because of kernel panic, it won't
shutdown devices. On-flight DMA will continue transferring data until
device driver initializes. All devices are supposed to reset during
driver initialization. And this property is used to fix the kdump
failure in system with intel iommu. Other systems with hardware iommu
should be similar. Please check commit 091d42e4 ("iommu/vt-d: Copy
translation tables from old kernel") and those commits around.

But bnx2 driver doesn't reset device during driver initialization. The
device resetting is deferred to net device up stage. This will cause
hardware iommu handling failure on bnx2 device. And its resetting relies
on firmware. So in this patch move the firmware requesting code to earlier
bnx2_init_one(), then next call bnx2_reset_chip to reset device.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Endianess fix for the new nf_tables netlink trace infrastructure,
   NFTA_TRACE_POLICY endianess was not correct, patch from Liping Zhang.

2) Fix broken re-route after userspace queueing in nf_tables route
   chain. This patch is large but it is simple since it is just getting
   this code in sync with iptable_mangle. Also from Liping.

3) NAT mangling via ctnetlink lies to userspace when nf_nat_setup_info()
   fails to setup the NAT conntrack extension. This problem has been
   there since the beginning, but it can now show up after rhashtable
   conversion.

4) Fix possible NULL pointer dereference due to failures in allocating
   the synproxy and seqadj conntrack extensions, from Gao feng.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When memory is exhausted, nfct_seqadj_ext_add may fail to add the
synproxy and seqadj extensions. The function nf_ct_seqadj_init doesn't
check if get valid seqadj pointer by the nfct_seqadj.

Now drop the packet directly when fail to add seqadj extension to
avoid dereference NULL pointer in nf_ct_seqadj_init from
init_conntrack().
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nf_nat_setup_info() returns NF_* verdicts, so convert them to error
codes that is what ctnelink expects. This has passed overlook without
having any impact since this nf_nat_setup_info() has always returned
NF_ACCEPT so far. Since 870190a9 ("netfilter: nat: convert nat bysrc
hash to rhashtable"), this is problem.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull networking fixes from David Miller:
 "Mostly small sets of driver fixes scattered all over the place.

   1) Mediatek driver fixes from Sean Wang.  Forward port not written
      correctly during TX map, missed handling of EPROBE_DEFER, and
      mistaken use of put_page() instead of skb_free_frag().

   2) Fix socket double-free in KCM code, from WANG Cong.

   3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for
      using the dcbx buffers before initializing them.

   4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for
      double fib removals and an error handling fix in
      mlxsw_sp_module_init().

   5) Fix kernel panic when enabling LLDP in i40e driver, from Dave
      Ertman.

   6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham.

   7) TCP's rcv_wup not initialized properly when using fastopen, from
      Neal Cardwell.

   8) Don't use uninitialized flow keys in flow dissector, from Gao
      Feng.

   9) Use after free in l2tp module unload, from Sabrina Dubroca.

  10) Fix interrupt registry ordering issues in smsc911x driver, from
      Jeremy Linton.

  11) Fix crashes in bonding having to do with enslaving and rx_handler,
      from Mahesh Bandewar.

  12) AF_UNIX deadlock fixes from Linus.

  13) In mlx5 driver, don't read skb->xmit_mode after it might have been
      freed from the TX reclaim path.  From Tariq Toukan.

  14) Fix a bug from 2015 in TCP Yeah where the congestion window does
      not increase, from Artem Germanov.

  15) Don't pad frames on receive in NFP driver, from Jakub Kicinski.

  16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo
      Leitner.

  17) Fix deletion of VRF routes, from Mark Tomlinson.

  18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
  net/mlx4_en: Fix panic on xmit while port is down
  net/mlx4_en: Fixes for DCBX
  net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
  net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
  net: ethernet: renesas: sh_eth: add POST registers for rz
  drivers: net: phy: mdio-xgene: Add hardware dependency
  dwc_eth_qos: do not register semi-initialized device
  sctp: identify chunks that need to be fragmented at IP level
  mlxsw: spectrum: Set port type before setting its address
  mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init
  nfp: don't pad frames on receive
  nfp: drop support for old firmware ABIs
  nfp: remove linux/version.h includes
  tcp: cwnd does not increase in TCP YeAH
  net/mlx5e: Fix parsing of vlan packets when updating lro header
  net/mlx5e: Fix global PFC counters replication
  net/mlx5e: Prevent casting overflow
  net/mlx5e: Move an_disable_cap bit to a new position
  net/mlx5e: Fix xmit_more counter race issue
  tcp: fastopen: avoid negative sk_forward_alloc
  ...

A fixed mpath was not quite being treated as such:

1) if a PERR frame was received, a fixed mpath was
   deactivated.

2) queued path discovery for fixed mpath was potentially
   being considered, changing mpath state.

3) other mpath flags were potentially being inherited when
   fixing the mpath. Just assign PATH_FIXED and SN_VALID.

This solves several issues when fixing a mesh path in one
direction. The reverse direction mpath should probably
also be fixed, or root announcements at least be enabled.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When using intermediate queues, sequence number allocation is deferred
until dequeue. This doesn't work for PS response frames, which bypass
those queues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Handle the case where the mac80211 intermediate queues are empty and the
driver has buffered frames

Fixes: ba8c3d6f ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Tariq Toukan says:

====================
mlx4 fixes

This patchset contains several bug fixes from the team to the
mlx4 Eth driver.

Series generated against net commit:
c2f57fb9 "drivers: net: phy: mdio-xgene: Add hardware dependency"

v2:
* excluded some cleanup patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.

Fixes: 63a664b7 ("net/mlx4_en: fix tx_dropped bug")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.

Fixes: af7d5185 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.

Fixes: af7d5185 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.

Fixes: af7d5185 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit aa719874 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).

Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull IIO fixes from Greg KH:
 "Here are a few small IIO fixes for 4.8-rc6.

  Nothing major, full details are in the shortlog, all of these have
  been in linux-next with no reported issues"

* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio:core: fix IIO_VAL_FRACTIONAL sign handling
  iio: ensure ret is initialized to zero before entering do loop
  iio: accel: kxsd9: Fix scaling bug
  iio: accel: bmc150: reset chip at init time
  iio: fix pressure data output unit in hid-sensor-attributes
  tools:iio:iio_generic_buffer: fix trigger-less mode

Pull USB fixes from Greg KH:
 "Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.

  All of these resolve minor issues that have been reported, and all
  have been in linux-next with no reported issues"

* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
  xhci: fix null pointer dereference in stop command timeout function
  usb: dwc3: pci: fix build warning on !PM_SLEEP
  usb: gadget: prevent potenial null pointer dereference on skb->len
  usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
  usb: phy: phy-generic: Check clk_prepare_enable() error
  usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
  Revert "usb: dwc3: gadget: always decrement by 1"

Due to a mistake in the hardware manual, the FWSLC and POST1-4 registers
were not documented and left out of the driver for RZ/A making the CAM
feature non-operational.
Additionally, when the offset values for POST1-4 are left blank, the driver
attempts to set them using an offset of 0xFFFF which can cause a memory
corruption or panic.

This patch fixes the panic and properly enables CAM.
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "nvdimm fixes for v4.8, two of them are tagged for -stable:

   - Fix devm_memremap_pages() to use track_pfn_insert().  Otherwise,
     DAX pmd mappings end up with an uncached pgprot, and unusable
     performance for the device-dax interface.  The device-dax interface
     appeared in 4.7 so this is tagged for -stable.

   - Fix a couple VM_BUG_ON() checks in the show_smaps() path to
     understand DAX pmd entries.  This fix is tagged for -stable.

   - Fix a mis-merge of the nfit machine-check handler to flip the
     polarity of an if() to match the final version of the patch that
     Vishal sent for 4.8-rc1.  Without this the nfit machine check
     handler never detects / inserts new 'badblocks' entries which
     applications use to identify lost portions of files.

   - For test purposes, fix the nvdimm_clear_poison() path to operate on
     legacy / simulated nvdimm memory ranges.  Without this fix a test
     can set badblocks, but never clear them on these ranges.

   - Fix the range checking done by dax_dev_pmd_fault().  This is not
     tagged for -stable since this problem is mitigated by specifying
     aligned resources at device-dax setup time.

  These patches have appeared in a next release over the past week.  The
  recent rebase you can see in the timestamps was to drop an invalid fix
  as identified by the updated device-dax unit tests [1].  The -mm
  touches have an ack from Andrew"

[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
   https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm: allow legacy (e820) pmem region to clear bad blocks
  nfit, mce: Fix SPA matching logic in MCE handler
  mm: fix cache mode of dax pmd mappings
  mm: fix show_smap() for zone_device-pmd ranges
  dax: fix mapping size check

Pull i2c fixes from Wolfram Sang:
 "Mostly driver bugfixes, but also a few cleanups which are nice to have
  out of the way"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: rk3x: Restore clock settings at resume time
  i2c: Spelling s/acknowedge/acknowledge/
  i2c: designware: save the preset value of DW_IC_SDA_HOLD
  Documentation: i2c: slave-interface: add note for driver development
  i2c: mux: demux-pinctrl: run properly with multiple instances
  i2c: bcm-kona: fix inconsistent indenting
  i2c: rcar: use proper device with dma_mapping_error
  i2c: sh_mobile: use proper device with dma_mapping_error
  i2c: mux: demux-pinctrl: invalidate properly when switching fails

Pull fscrypto fixes fromTed Ts'o:
 "Fix some brown-paper-bag bugs for fscrypto, including one one which
  allows a malicious user to set an encryption policy on an empty
  directory which they do not own"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  fscrypto: require write access to mount to set encryption policy
  fscrypto: only allow setting encryption policy on directories
  fscrypto: add authorization check for setting encryption policy

Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem.  This was handled correctly by f2fs but not by ext4.  Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>

The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files.  This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.

In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.

This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later.  It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.

This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access.  This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).

Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy.  This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.

(*) Or also on any regular file, for f2fs v4.6 and later and ext4
    v4.8-rc1 and later; a separate bug fix is coming for that.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.8

iwlwifi

* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode

ath10k

* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message

ath9k

* fix regression with led GPIOs
* fix AR5416 GPIO access warning

brcmfmac

* avoid potential stack overflow in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We move register_netdev() to the end of dwceqos_probe() to close any
races where the netdev callbacks are called before the initialization
has finished.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, without GSO, it was easy to identify it: if the chunk didn't
fit and there was no data chunk in the packet yet, we could fragment at
IP level. So if there was an auth chunk and we were bundling a big data
chunk, it would fragment regardless of the size of the auth chunk. This
also works for the context of PMTU reductions.

But with GSO, we cannot distinguish such PMTU events anymore, as the
packet is allowed to exceed PMTU.

So we need another check: to ensure that the chunk that we are adding,
actually fits the current PMTU. If it doesn't, trigger a flush and let
it be fragmented at IP level in the next round.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.

Fixes: 6839a6d9 nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>