This patch removes sti_secondary_start from _INIT section, there are 2
reason for this removal.
 1. discarding such a small code does not save much, given the RAM
sizes.
 2. Having this code discarded, creates corruption issue when we boot
smp-kernel with nrcpus=1 or with single cpu node in DT.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes cpu nodes with device_type = "cpu". This change was not
necessary before 3.10-rc7.
Without this patch STi SOCs does not boot as SMP.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman:
Second round of Renesas ARM based SoC fixes for v3.11

* Lager board: do not annotate gpio_buttons as __initdata
  - This avoids accessing uninitialised memory if keys are pressed
    after kernel initialisation completes.
  - Bug introduced in gpio-keys were enabled in v3.11-rc1

* Bock-W board: fix SDHI0 PFC settings
  - Allow detection of SD card
  - Bug introduced in SDHI support was added in v3.11-rc1

* shdma: fixup sh_dmae_get_partial() calculation error
  - Bug introduced in 2.6.34-rc1.

* armadillo800eva board: Don't request GPIO 166 in board code
  - Allow use of touchscreen
  - Bug introduced in v3.11-rc1

* tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
  ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
  shdma: fixup sh_dmae_get_partial() calculation error
  ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'for-v3.11-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

From Paul Walmsley via Tony Lindgren:
Some OMAP hwmod fixes for v3.11-rc.  Mostly intended to fix an earlyprintk
regression and an AM33xx cpgmac power management regression.

Basic build, boot, and PM tests are available here:

http://www.pwsan.com/omap/testlogs/hwmod_fixes_a_v3.11-rc/20130730042132/

The tests include temporary fixes for the unrelated 2430SDP and OMAP3
boot regressions, which are not part of this signed tag.

* tag 'for-v3.11-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
  ARM: OMAP2+: hwmod: rt address space index for DT
  ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
  ARM: OMAP2+: Avoid idling memory controllers with no drivers
  ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.11/fixes-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Fixes for omap5-uevm regulators from Nishanth Menon <nm@ti.com>:

Due to wrong older revision of documentation used as reference, we
seem to have a bunch of LDOs wrongly configured on OMAP5 uEVM. This
series is based power tree on production board 750-2628-XXX platform.
Unfortunately, the wrong voltages may be detrimental to OMAP5 as they
supply hardware blocks at voltages that are out of specification.

There is a chance that without these fixes there can be hardware
damage to omap5-uevm boards with the v3.11-rc series.

* tag 'omap-for-v3.11/fixes-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap5-uevm: update optional/unused regulator configurations
  ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
  ARM: dts: omap5-uevm: document regulator signals used on the actual board
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'msm-3.11-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes

From David Brown, fixes for MSM for 3.11:

Two small fixes for MSM.

The first fixes the a gpio controller register address.  I didn't see
any acks from the devicetree maintainers, so I've copied them on this
pull request.  The change itself is minor, and just to the register
address.

The second change removes the gpiomux V1 code from MSM.  This was
breaking compilation for some of the targets.

* tag 'msm-3.11-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
  ARM: msm: Consolidate gpiomux for older architectures
  ARM: msm: dts: Fix the gpio register address for msm8960
Signed-off-by: Olof Johansson <olof@lixom.net>

When the gpio-keys device is registered using
platform_device_register_data() the platform data argument,
lager_keys_pdata is duplicated and thus should be marked as __initdata
to avoid wasting memory. However, this is not true of gpio_buttons,
a reference to it rather than its value is duplicated when lager_keys_pdata
is duplicated.

This avoids accessing freed memory if gpio-key events occur
after unused kernel memory is freed late in the kernel's boot.

This but was added when support for gpio-keys was added to lager
in c3842e4f
("ARM: shmobile: lager: support GPIO switches") which was included
in v3.11-rc1.
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The following message is printed on the BOCK-W kernel bootup:

sh-pfc pfc-r8a7778: invalid group "sdhi0" for function "sdhi0"

In addition, SD card cannot be detected.  The reason is apparently that commit
ca7bb309 (ARM: shmobile: bockw: add SDHI0 support) matched
the previous version of commit 564617d2 (sh-pfc: r8a7778:
add SDHI support).

Add the missing pin groups according to the BOCK-W board schematics.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh_desc->hw.tcr is controlling real data size,
and, register TCR is controlling data transfer count
which was xmit_shifted value of hw.tcr.
Current sh_dmae_get_partial() is calculating in different unit.
This patch fixes it.

This bug has been present since c014906a
("dmaengine: shdma: extend .device_terminate_all() to record partial
transfer"), which was added in 2.6.34-rc1.

Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Register target address to be used for cpgmac is the second device
address space. By default, hwmod picks first address space (0th index)
for register target.

With removal of address space from hwmod and using DT instead, cpgmac
is getting wrong address space for register target.

Fix it by indicating the address space to be used for register target.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.

Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled
state post setup(). When a omap_device gets created for such hwmods
make sure the omap_device and pm_runtime states are also in sync for such
hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the
device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with
HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup.

Even if they have drivers missing, avoid idling them as part of
omap_device_late_idle()
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

With commit '82702ea1' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.

This was rootcaused to hwmod trying to reset console uart while
earlycon was using it.  The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.

Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.

This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

commit e00c27ef
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.

The following optional/unused regulators can be updated:

- SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be
enabled only when audio is active. Since it does not come active by
default, it does not require "always-on" or "boot-on".

- LDO2 and LDO8 do not go to any peripheral or connector on the board.
Further, these unused regulators should have been 2.8V for LDO2 and
3.0V for LDO8. Mark these LDOs as disabled in the dts until needed.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit e00c27ef
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.

The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:

- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.

To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.

Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.

- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.

Further, vdda_lli is supposed to be 1.5V and not 3V.

- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi

This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.

To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.

Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.

- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.

- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".

So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.

Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.

- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit e00c27ef
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 - Driver fixes for AM33xx, SIRF and PFC pin controllers
 - Fix a compile warning from the pinctrl single-register driver
 - Fix a little nasty memory leak

* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix a memleak when freeing maps
  pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
  pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
  arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
  pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
  pinctrl: sirf: fix the pin number and mux bit for usp0
  pinctrl: am33xx dt binding: correct include path

Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Oleg is working on fixing a very tight race between opening a event
  file and deleting that event at the same time (both must be done as
  root).

  I also found a bug while testing Oleg's patches which has to do with a
  race with kprobes using the function tracer.

  There's also a deadlock fix that was introduced with the previous
  fixes"

* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
  ftrace: Add check for NULL regs if ops has SAVE_REGS set
  tracing: Kill trace_cpu struct/members
  tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
  tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
  tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
  tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
  tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
  tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()

Pull SCSI fixes from James Bottomley:
 "This is five bug fixes, two of which fix long standing problems
  causing crashes (sd and mvsas).  The remaining three are hung (isci
  race) or lost (qla2xxx, isci) devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] isci: fix breakage caused by >16byte CDB patch
  [SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
  [SCSI] sd: fix crash when UA received on DIF enabled device
  [SCSI] qla2xxx: Properly set the tagging for commands.
  [SCSI] isci: Fix a race condition in the SSP task management path

Msm gpiomux can be used only for 7x30 and 8x50.
Prevent compilation and fix build issues on 7X00, 8X60 and 8960.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>

Pull drm fixes from Dave Airlie:
 "This is just a regular fixes pull apart from the qxl one, it has
  radeon and intel bits in it,

  The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
  regression, whereas radeon is more DPM fixes, a few lockup fixes and
  some rn50/r100 DAC fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/dpm: fix r600_enable_sclk_control()
  drm/radeon/dpm: implement force performance levels for rv6xx
  drm/radeon/dpm: fix displaygap programming on rv6xx
  drm/radeon/dpm: fix a typo in the rv6xx mclk setup
  drm/i915: initialize gt_lock early with other spin locks
  drm/i915: fix hdmi portclock limits
  drm/radeon: fix combios tables on older cards
  drm/radeon: improve dac adjust heuristics for legacy pdac
  drm/radeon: Another card with wrong primary dac adj
  drm/radeon: fix endian issues with DP handling (v3)
  drm/radeon/vm: only align the pt base to 32k
  drm/radeon: wait for 3D idle before using CP DMA

Pull qxl drm fixes from Dave Airlie:
 "Okay as I warned, the qxl driver was running a bit free and loose with
  its ttm object reservations and the new lockdep enabled reservation
  tracking shone a bright light into it, it also with the new
  reservations mutexes hits a possible deadlock during boot.

  The first patch is a real fix to render the console correctly as the
  driver used to just drop irq renderering as too hard, this also fixes
  a sleeping while atomic warning.

  The other two patches are the big ugly ones that redo how the driver
  allocates objects and reserves them and makes things all work
  properly, I've tested this in a VM, and compared to the current code
  which hits a lockdep warning and the sleep while atomic warning before
  failing.

  So sorry this is coming in late, I should have tested qxl before
  merging the mutex code, but I'd rather just fix qxl with this than
  revert the reservations code at this point"

* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
  qxl: convert qxl driver to proper use for reservations
  qxl: allow creation of pre-pinned objects and use for releases.
  drm/qxl: add delayed fb operations

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are just two fixes, a revert of the would-be backlight fix that
  didn't work and an intel_pstate fix for two problems related to
  maximum P-state selection.

  Specifics:

   - Revert of the ACPI video commit that I hoped would help fix
     backlight problems related to Windows 8 compatibility on some
     systems.  Unfortunately, it turned out to cause problems to happen
     too.

   - Fix for two problems in intel_pstate, a possible failure to respond
     to a load change on a quiet system and a possible failure to select
     the highest available P-state on some systems.  From Dirk
     Brandewie"

* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
  cpufreq / intel_pstate: Change to scale off of max P-state

Pull arm64 fixes from Catalin Marinas:
 - Stack size increased to 16K (similar to other 64-bit architectures)
 - Additional cache flushing for secondary CPUs boot mode

* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: Change kernel stack size to 16K
  arm64: Fix definition of arm_pm_restart to match the declaration
  arm64: virt: ensure visibility of __boot_cpu_mode

Pull ARM SoC fixes from Olof Johansson:
 "This is a largeish batch of fixes, mostly because I missed -rc2 due to
  travel/vacation.  So in number these are a bit more than ideal unless
  you amortize them over two -rcs.

  Quick breakdown:
   - Defconfig updates
     - Making multi_v7_defconfig useful on more hardware to encourage
       single-image usage
     - Davinci and nomadik updates due to new code merged this merge
       window
   - Fixes for UART on Samsung platforms, both PM and clock-related
   - A handful of warning fixes from defconfig builds, including for
     max8925 backlight and pxamci (both with appropriate acks)
   - Exynos5440 fixes for LPAE configuration, PM
   - ...plus a bunch of other smaller changes all over the place

  I expect to switch to regressions-or-severe-bugs-only fixes from here
  on out"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
  mfd: max8925: fix dt code for backlight
  ARM: omap5: Only select errata 798181 if SMP
  ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
  ARM: EXYNOS: Fix low level debug support
  ARM: SAMSUNG: Save/restore only selected uart's registers
  ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
  ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
  ARM: multi_v7_defconfig: Select USB chipidea driver
  ARM: pxa: propagate errors from regulator_enable() to pxamci
  ARM: zynq: fix compilation warning
  ARM: keystone: fix compilation warning
  ARM: highbank: Only touch common coherency control register fields
  ARM: footbridge: fix overlapping PCI mappings
  dmaengine: shdma: fix a build failure on platforms with no DMA support
  ARM: STi: Set correct ARM ERRATAs.
  ARM: dts: STi: Fix pinconf setup for STiH416 serial2
  ARM: nomadik: configure for NO_HZ and HRTIMERS
  ARM: nomadik: update defconfig base
  ARM: nomadik: Update MMC defconfigs
  ARM: davinci: defconfig: enable EDMA driver
  ...

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for 3.11-rc3.

  Lots of little things, nothing major.  A number of new device ids,
  build fixes for DMA, and a bunch of other minor things.  All of these
  have been in the linux-next tree"

* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
  usb: Clear both buffers when clearing a control transfer TT buffer.
  usb/gadget: free opts struct on error recovery
  USB: mos7840: fix memory leak in open
  usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
  usb: serial: option: add Olivetti Olicard 200
  usb: serial: option: blacklist ONDA MT689DC QMI interface
  xhci: fix null pointer dereference on ring_doorbell_for_active_rings
  usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
  usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
  usb: xhci: Mark two functions __maybe_unused
  xhci: Avoid NULL pointer deref when host dies.
  usb: serial: option: Add ONYX 3G device support
  USB: ti_usb_3410_5052: fix dynamic-id matching
  usb: option: add TP-LINK MA260
  USB: option: add D-Link DWM-152/C1 and DWM-156/C1
  USB: EHCI: Fix resume signalling on remote wakeup
  USB: cp210x: add MMB and PI ZigBee USB Device Support
  usb: cp210x support SEL C662 Vendor/Device
  USB: option: append Petatel NP10T device to GSM modems list
  USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
  ...

Pull tty/serial fixes from Greg KH:
 "Here are 3 fixes for TTY and serial issues that have been reported.
  Nothing huge, but nice to get fixed"

* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
  tty/8250_early: Don't truncate last character of options
  TTY: snyclinkmp: calculating wrong addresses

Pull staging fixes from Greg KH:
 "Here are some tiny drivers/staging/ fixes for 3.11-rc3

  A number of bugfixes, all pretty tiny, but resolve issues that have
  been reported (the kstrtos32 change fixes a data corruption problem
  that Dan found).  And a MAINTAINERS file update for the comedi
  drivers"

* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  MAINTAINERS: Update the list of maintainers for staging/comedi driver.
  staging: tidspbridge: replace strict_strtol() with kstrtos32()
  staging: android: logger: Correct write offset reset on error
  staging: zram: protect zram_reset_device() call
  staging: gdm72xx: potential use after free in send_qos_list()
  staging: drm/imx: drop "select OF_VIDEOMODE"
  staging: frontier: use after free in disconnect()
  staging: comedi: fix a race between do_cmd_ioctl() and read/write
  staging: comedi: COMEDI_CANCEL ioctl should wake up read/write

Pull char/misc patches from Greg KH:
 "Here are some char/misc patches for 3.11-rc3.  It's pretty much just:
   - mei fixes
   - hyperv fixes
   - new ja_JP translation update
  all tiny stuff, but fixes for issues people have reported."

* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  HOWTO ja_JP sync
  mei: me: fix waiting for hw ready
  mei: don't have to clean the state on power up
  mei: me: fix reset state machine
  mei: hbm: fix typo in error message
  Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
  Drivers: hv: balloon: Do not post pressure status if interrupted
  Drivers: hv: balloon: Fix a bug in the hot-add code
  Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered

Pull sound fixes from Takashi Iwai:
 "Just a handful of regression and small fixes in ASoC, HD-audio and
  USB-audio drivers.

   - Sigmetal HD-audio codec regression fixes
   - A copule of XRUN indication fixes for usb-audio devices
   - ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
     max98088 register access fix, etc"

* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hiface: return correct XRUN indication
  ASoC: tegra: correct playback_dma_data setup
  ASoC: core: double free in snd_soc_add_platform()
  ALSA: usb-audio: 6fire: return correct XRUN indication
  ASoC: ep93xx: fix build of ep93xx-ac97.c
  ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
  ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
  ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
  ASoC: sgtl5000: defer the probe if clock is not found
  ASoC: max98088 - fix element type of the register cache.

Pull xfs fix from Ben Myers:
 "Fix for regression in commit cca9f93a ("xfs: don't do IO when
  creating an new inode"), recovery causing filesystem corruption after
  a crash"

* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
  xfs: di_flushiter considered harmful

Pull nfsd fix from Bruce Fields:
 "One more nfsd bugfix for 3.11"

* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
  nfsd: nfsd_open: when dentry_open returns an error do not propagate as struct file

Pull md fixes from Neil Brown:
 "Two more bugfixes for md in 3.11

  Both marked for -stable, both since 3.3.  I guess I should spend more
  time testing..."

* tag 'md/3.11-fixes' of git://neil.brown.name/md:
  md/raid5: fix interaction of 'replace' and 'recovery'.
  md/raid10: remove use-after-free bug.

Pull libata fixes from Tejun Heo:
 "Assorted libata updates.

  The most critical one is a fix for ahci oops during boot.  Also, a new
  smallish platform ahci driver is added and sata_inic162x is marked
  clearly as experimental (it whines during boot too) as data corruption
  seems rather common on the device and it's unlikely to get any love in
  the foreseeable future.  If the whining doesn't draw any attention, I
  think we'd probably be better of making the driver depend on BROKEN in
  a couple releases"

This is v2 of this pull request with fixed dependencies for ahci_imx.

* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci_imx: depend on CONFIG_MFD_SYSCON
  ahci_imx: add ahci sata support on imx platforms
  ARM: imx6q: update the sata bits definitions of gpr13
  ahci: fix Null pointer dereference in achi_host_active()
  libata: make it clear that sata_inic162x is experimental
  libata: replace strict_strtol() with kstrtol()
  ata: Fix DVD not dectected at some platform with Wellsburg PCH

We attempted to address a regression introduced by commit a57f7f91
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8.  That problem is tracked by the bug entry at:

https://bugzilla.kernel.org/show_bug.cgi?id=51231

Commit 8c5bd7ad (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.

For this reason, revert commit 8c5bd7ad, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.

References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27Reported-and-tested-by: James Hogan <james@albanarts.com>
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Reported-by: Kalle Valo <kvalo@adurom.com>
Tested-by: Joerg Platte <jplatte@naasa.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not.  Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>

Commit a8227415 "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.

This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.

Commit a8227415 was marked for stable, which means this must be
sent to stable too.

Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.comReported-by: Arend van Spril <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Cc: Alexander Z Lam <azl@google.com>
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: Feng Kan <fkan@apm.com>
Acked-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>