If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.

Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.

Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9e42f715 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.

This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.

Fixes: 9e42f715 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The collect metadata mode does not support GUE nor FOU. This might be
implemented later; until then, we should reject such config.

I think this is okay to be changed. It's unlikely anyone has such
configuration (as it doesn't work anyway) and we may need a way to
distinguish whether it's supported or not by the kernel later.

For backwards compatibility with iproute2, it's not possible to just check
the attribute presence (iproute2 always includes the attribute), the actual
value has to be checked, too.

Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petko Manolov says:

====================
pegasus: correct buffer & packet sizes

As noticed by Lincoln Ramsay <a1291762@gmail.com> some old (usb 1.1) Pegasus
based devices may actually return more bytes than the specified in the datasheet
amount.  That would not be a problem if the allocated space for the SKB was
equal to the parameter passed to usb_fill_bulk_urb().  Some poor bugger (i
really hope it was not me, but 'git blame' is useless in this case, so anyway)
decided to add '+ 8' to the buffer length parameter.  Sometimes the usb transfer
overflows and corrupts the socket structure, leading to kernel panic.

The above doesn't seem to happen for newer (Pegasus2 based) devices which did
help this bug to hide for so long.

The new default is to not include the CRC at the end of each received package.
So far CRC has been ignored which makes no sense to do it in a first place.

The patch is against v4.6-rc5 and was tested on ADM8515 device by transferring
multiple gigabytes of data over a couple of days without any complaints from the
kernel.  Please apply it to whatever net tree you deem fit.

Changes since v1:

 - split the patch in two parts;
 - corrected the subject lines;

Changes since v2:

 - do not append CRC by default (based on a discussion with Johannes Berg);
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The default Pegasus setup was to append the status and CRC at the end of each
received packet.  The status bits are used to update various stats, but CRC has
been ignored.  The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Benc says:

====================
gre: fix lwtunnel support

This patchset fixes a few bugs in ipgre metadata mode implementation.

As an example, in this setup:

ip a a 192.168.1.1/24 dev eth0
ip l a gre1 type gre external
ip l s gre1 up
ip a a 192.168.99.1/24 dev gre1
ip r a 192.168.99.2/32 encap ip dst 192.168.1.2 ttl 10 dev gre1
ping 192.168.99.2

the traffic does not go through before this patchset and does as expected
with it applied.

v3: Back to v1 in order not to break existing users. Dropped patch 3, will
    be fixed in iproute2 instead.
v2: Rejecting invalid configuration, added patch 3, dropped patch for
    ETH_P_TEB (will target net-next).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In ipgre (i.e. not gretap) + collect metadata mode, the skb was assumed to
contain Ethernet header and was encapsulated as ETH_P_TEB. This is not the
case, the interface is ARPHRD_IPGRE and the protocol to be used for
encapsulation is skb->protocol.

Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ipgre mode (i.e. not gretap) with collect metadata flag set, the tunnel
is incorrectly assumed to be mGRE in NBMA mode (see commit 6a5f44d7).
This is not the case, we're controlling the encapsulation addresses by
lwtunnel metadata. And anyway, assigning dev->header_ops in collect metadata
mode does not make sense.

Although it would be more user firendly to reject requests that specify
both the collect metadata flag and a remote/local IP address, this would
break current users of gretap or introduce ugly code and differences in
handling ipgre and gretap configuration. Keep the current behavior of
remote/local IP address being ignored in such case.

v3: Back to v1, added explanation paragraph.
v2: Reject configuration specifying both remote/local address and collect
    metadata flag.

Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a single fix, for a per-CPU memory leak in a
(root user triggerable) error case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030.  However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
In this patchset you can find the following fixes:

1) check skb size to avoid reading beyond its border when delivering
   payloads, by Sven Eckelmann
2) initialize last_seen time in neigh_node object to prevent cleanup
   routine from accidentally purge it, by Marek Lindner
3) release "recently added" slave interfaces upon virtual/batman
   interface shutdown, by Sven Eckelmann
4) properly decrease router object reference counter upon routing table
   update, by Sven Eckelmann
5) release queue slots when purging OGM packets of deactivating slave
   interface, by Linus Lüssing

Patch 2 and 3 have no "Fixes:" tag because the offending commits date
back to when batman-adv was not yet officially in the net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The size allocated for target->hwinfo and the number of bytes copied in it
should be consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix casting in net_gso_ok. Otherwise the shift on
gso_type << NETIF_F_GSO_SHIFT may hit the 32th bit and make it look like
a INT_MIN, which is then promoted from signed to uint64 which is
0xffffffff80000000, resulting in wrong behavior when it is and'ed with
the feature itself, as in:

This test app:
#include <stdio.h>
#include <stdint.h>

int main(int argc, char **argv)
{
	uint64_t feature1;
	uint64_t feature2;
	int gso_type = 1 << 15;

	feature1 = gso_type << 16;
	feature2 = (uint64_t)gso_type << 16;
	printf("%lx %lx\n", feature1, feature2);

	return 0;
}

Gives:
ffffffff80000000 80000000

So that this:
   return (features & feature) == feature;
Actually works on more bits than expected and invalid ones.

Fix is to promote it earlier.

Issue noted while rebasing SCTP GSO patch but posting separetely as
someone else may experience this meanwhile.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configured in fixed link, the DaVinci emac driver sets the
priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl()
causes the kernel to crash.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 1bb6aa56 ("net: davinci_emac: Add support for fixed-link PHY")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.6

ath9k

* fix a couple release old throughput regression on ar9281

iwlwifi

* add new device IDs for 8265
* fix a NULL pointer dereference when paging firmware asserts
* remove a WARNING on gscan capabilities
* fix MODULE_FIRMWARE for 8260
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myself and Edward Cree as maintainers.
Remove Shradha Shah, who is on extended leave.

Cc: David S. Miller <davem@davemloft.net>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When certain firmware variants are selected (via the sfboot utility) the
SFC7000 and SFC8000 series NICs don't support RSS. The driver still
tries (and fails) to insert filters with the RSS flag, and the NIC fails
to pass traffic.

When the firmware reports RSS_LIMITED suppress allocating a default RSS
context. The absence of an RSS context is picked up in filter insertion
and RSS flags are discarded.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_disable() can not be called with bh disabled, move locking just
around myri10ge_ss_lock_napi() .

Patches fixes following bug:

[  114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383
<snip>
[  114.313712] Call Trace:
[  114.314943]  [<ffffffff817010ce>] dump_stack+0x19/0x1b
[  114.317673]  [<ffffffff810ce7f3>] __might_sleep+0x173/0x230
[  114.320566]  [<ffffffff815b3117>] napi_disable+0x27/0x90
[  114.323254]  [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Engestrom <eric@engestrom.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes for net.

Only use MSIX on VF, and fix rx page buffers on architectures with
PAGE_SIZE >= 64K.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD.  Divide the page
into multiple 32K buffers for the aggregation ring.

Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer.  Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535.  For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers.  It won't work if the native CPU page size is
64K or bigger.

We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K.  Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.

The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only MSI-X can be used on a VF.  The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case that dev_alloc_name() fails, e.g. because the name was
given by the user and already exists, we need to clean up properly
and free the per-CPU statistics. Fix that.

Cc: stable@vger.kernel.org
Fixes: 5a490510 ("mac80211: use per-CPU TX/RX statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:

 1) Handle v4/v6 mixed sockets properly in soreuseport, from Craig
    Gallak.

 2) Bug fixes for the new macsec facility (missing kmalloc NULL checks,
    missing locking around netdev list traversal, etc.) from Sabrina
    Dubroca.

 3) Fix handling of host routes on ifdown in ipv6, from David Ahern.

 4) Fix double-fdput in bpf verifier.  From Jann Horn.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
  bpf: fix double-fdput in replace_map_fd_with_map_ptr()
  net: ipv6: Delete host routes on an ifdown
  Revert "ipv6: Revert optional address flusing on ifdown."
  net/mlx4_en: fix spurious timestamping callbacks
  net: dummy: remove note about being Y by default
  cxgbi: fix uninitialized flowi6
  ipv6: Revert optional address flusing on ifdown.
  ipv4/fib: don't warn when primary address is missing if in_dev is dead
  net/mlx5: Add pci shutdown callback
  net/mlx5_core: Remove static from local variable
  net/mlx5e: Use vport MTU rather than physical port MTU
  net/mlx5e: Fix minimum MTU
  net/mlx5e: Device's mtu field is u16 and not int
  net/mlx5_core: Add ConnectX-5 to list of supported devices
  net/mlx5e: Fix MLX5E_100BASE_T define
  net/mlx5_core: Fix soft lockup in steering error flow
  qlcnic: Update version to 5.3.64
  net: stmmac: socfpga: Remove re-registration of reset controller
  macsec: fix netlink attribute validation
  macsec: add missing macsec prefix in uapi
  ...

Pull ARM SoC fixes from Arnd Bergmann:
 "Here are the latest bug fixes for ARM SoCs, mostly addressing recent
  regressions.  Changes are across several platforms, so I'm listing
  every change separately here.

  Regressions since 4.5:

   - A correction of the psci firmware DT binding, to prevent users from
     relying on unintended semantics

   - Actually getting the newly merged clock driver for some OMAP
     platforms to work

   - A revert of patches for the Qualcomm BAM, these need to be reworked
     for 4.7 to avoid breaking boards other than the one they were
     intended for

   - A correction for the I2C device nodes on the Socionext Uniphier
     platform

   - i.MX SDHCI was broken for non-DT platforms due to a change with the
     setting of the DMA mask

   - A revert of a patch that accidentally added a nonexisting clock on
     the Rensas "Porter" board

   - A couple of OMAP fixes that are all related to suspend after the
     power domain changes for dra7

   - On Mediatek, revert part of the power domain initialization changes
     that broke mt8173-evb

  Fixes for older bugs:

   - Workaround for an "external abort" in the omap34xx suspend/resume
     code.

   - The USB1/eSATA should not be listed as an excon device on
     am57xx-beagle-x15 (broken since v4.0)

   - A v4.5 regression in the TI AM33xx and AM43XX DT specifying
     incorrect DMA request lines for the GPMC

   - The jiffies calibration on Renesas platforms was incorrect for some
     modern CPU cores.

   - A hardware errata woraround for clockdomains on TI DRA7"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  drivers: firmware: psci: unify enable-method binding on ARM {64,32}-bit systems
  arm64: dts: uniphier: fix I2C nodes of PH1-LD20
  ARM: shmobile: timer: Fix preset_lpj leading to too short delays
  Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
  ARM: dts: r8a7791: Don't disable referenced optional clocks
  Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
  ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
  ARM: dts: am57xx-beagle-x15: remove extcon_usb1
  ARM: dts: am437x: Fix GPMC dma properties
  ARM: dts: am33xx: Fix GPMC dma properties
  Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"
  ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask
  ARM: DRA7: clockdomain: Implement timer workaround for errata i874
  ARM: OMAP: Catch callers of revision information prior to it being populated
  ARM: dts: dra7: Correct clock tree for sys_32k_ck
  ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
  ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
  Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
  Revert "dts: msm8974: Add blsp2_bam dma node"
  ARM: dts: Add clocks for dm814x ADPLL

This is more prep-work for the upcoming pty changes.  Still just code
cleanup with no actual semantic changes.

This removes a bunch pointless complexity by just having the slave pty
side remember the dentry associated with the devpts slave rather than
the inode.  That allows us to remove all the "look up the dentry" code
for when we want to remove it again.

Together with moving the tty pointer from "inode->i_private" to
"dentry->d_fsdata" and getting rid of pointless inode locking, this
removes about 30 lines of code.  Not only is the end result smaller,
it's simpler and easier to understand.

The old code, for example, depended on the d_find_alias() to not just
find the dentry, but also to check that it is still hashed, which in
turn validated the tty pointer in the inode.

That is a _very_ roundabout way to say "invalidate the cached tty
pointer when the dentry is removed".

The new code just does

	dentry->d_fsdata = NULL;

in devpts_pty_kill() instead, invalidating the tty pointer rather more
directly and obviously.  Don't do something complex and subtle when the
obvious straightforward approach will do.

The rest of the patch (ie apart from code deletion and the above tty
pointer clearing) is just switching the calling convention to pass the
dentry or file pointer around instead of the inode.

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When bpf(BPF_PROG_LOAD, ...) was invoked with a BPF program whose bytecode
references a non-map file descriptor as a map file descriptor, the error
handling code called fdput() twice instead of once (in __bpf_map_get() and
in replace_map_fd_with_map_ptr()). If the file descriptor table of the
current task is shared, this causes f_count to be decremented too much,
allowing the struct file to be freed while it is still in use
(use-after-free). This can be exploited to gain root privileges by an
unprivileged user.

This bug was introduced in
commit 0246e64d ("bpf: handle pseudo BPF_LD_IMM64 insn"), but is only
exploitable since
commit 1be7f75d ("bpf: enable non-root eBPF programs") because
previously, CAP_SYS_ADMIN was required to reach the vulnerable code.

(posted publicly according to request by maintainer)
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was a simple idea -- save IPv6 configured addresses on a link down
so that IPv6 behaves similar to IPv4. As always the devil is in the
details and the IPv6 stack as too many behavioral differences from IPv4
making the simple idea more complicated than it needs to be.

The current implementation for keeping IPv6 addresses can panic or spit
out a warning in one of many paths:

1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in
   rt6_fill_node while handling a route dump request.

2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in
   fib6_del

3. Panic in fib6_purge_rt because rt6i_ref count is not 1.

The root cause of all these is references related to the host route for
an address that is retained.

So, this patch deletes the host route every time the ifdown loop runs.
Since the host route is deleted and will be re-generated an up there is
no longer a need for the l3mdev fix up. On the 'admin up' side move
addrconf_permanent_addr into the NETDEV_UP event handling so that it
runs only once versus on UP and CHANGE events.

All of the current panics and warnings appear to be related to
addresses on the loopback device, but given the catastrophic nature when
a bug is triggered this patch takes the conservative approach and evicts
all host routes rather than trying to determine when it can be re-used
and when it can not. That can be a later optimizaton if desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 841645b5.

Ok, this puts the feature back.  I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently ARM CPUs DT bindings allows different enable-method value for
PSCI based systems. On ARM 64-bit this property is required and must be
"psci" while on ARM 32-bit systems this property is optional and must
be "arm,psci" if present.

However, "arm,psci" has always been the compatible string for the PSCI
node, and was never intended to be the enable-method. So this is a bug
in the binding and not a deliberate attempt at specifying 32-bit
differently.

This is problematic if 32-bit OS is run on 64-bit system which has
"psci" as enable-method rather than the expected "arm,psci".

So let's unify the value into "psci" and remove support for "arm,psci"
before it finds any users.
Reported-by: Soby Mathew <Soby.Mathew@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.

Fixes: ec693d47 ("net/mlx4_en: Add HW timestamping (TS) support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_route_output looks into different fields in the passed flowi6 structure,
yet cxgbi passes garbage in nearly all those fields. Zero the structure out
first.

Fixes: fc8d0590 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts the following three commits:

70af921d
799977d9
f1705ec1

The feature was ill conceived, has terrible semantics, and has added
nothing but regressions to the already fragile ipv6 stack.

Fixes: f1705ec1 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David S. Miller <davem@davemloft.net>