Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make logging of an ethernet address more consistent with
the rest of the kernel.

Miscellanea:

The %02hx use also did not quite match the u8 definition
of addr though that did not actually matter given normal
integer promotion rules.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By default IPv6 socket with IPV6_ROUTER_ALERT socket option set will
receive all IPv6 RA packets from all namespaces.
IPV6_ROUTER_ALERT_ISOLATE socket option restricts packets received by
the socket to be only from the socket's namespace.
Signed-off-by: Maxim Martynov <maxim@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add __user attributes in some of the casts in this function to avoid
the following sparse warnings:

net/compat.c:592:57: warning: cast removes address space of expression
net/compat.c:592:57: warning: incorrect type in initializer (different address spaces)
net/compat.c:592:57:    expected struct compat_group_req [noderef] <asn:1>*gr32
net/compat.c:592:57:    got void *<noident>
net/compat.c:613:65: warning: cast removes address space of expression
net/compat.c:613:65: warning: incorrect type in initializer (different address spaces)
net/compat.c:613:65:    expected struct compat_group_source_req [noderef] <asn:1>*gsr32
net/compat.c:613:65:    got void *<noident>
net/compat.c:634:60: warning: cast removes address space of expression
net/compat.c:634:60: warning: incorrect type in initializer (different address spaces)
net/compat.c:634:60:    expected struct compat_group_filter [noderef] <asn:1>*gf32
net/compat.c:634:60:    got void *<noident>
net/compat.c:672:52: warning: cast removes address space of expression
net/compat.c:672:52: warning: incorrect type in initializer (different address spaces)
net/compat.c:672:52:    expected struct compat_group_filter [noderef] <asn:1>*gf32
net/compat.c:672:52:    got void *<noident>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were skipping the prepare phase which causes some problems with at
least a couple of drivers:

- mv88e6xxx chooses to skip programming VID = 0 with -EOPNOTSUPP in
  the prepare phase, but we would still try to force this VID since we
  would only call the commit phase and so we would get the driver to
  return -EINVAL instead

- qca8k does not currently have a port_vlan_add() callback implemented,
  yet we would try to call that unconditionally leading to a NPD

Fix both issues by conforming to the current model doing a
prepare/commit phase, this makes us consistent throughout the code and
assumptions.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 061f6a50 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add XDP_REDIRECT support

The first patch adds different software annotation types for Tx frames
depending on frame type while the second one actually adds support for basic
XDP_REDIRECT.

Changes in v2:
  - add missing xdp_do_flush_map() call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement support for the XDP_REDIRECT action.

The redirected frame is transmitted and confirmed on the regular Tx/Tx
conf queues. Frame is marked with the "XDP" type in the software
annotation, since it requires special treatment.

We don't have good hardware support for TX batching, so the
XDP_XMIT_FLUSH flag doesn't make a difference for now; ndo_xdp_xmit
performs the actual Tx operation on the spot.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We write different metadata information in the software annotation
area of Tx frames, depending on frame type. Make this more explicit
by introducing a type field and separate structures for single buffer
and scatter-gather frames.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Toke Høiland-Jørgensen says:

====================
sched: Patches from out-of-tree version of sch_cake

This series includes a couple of patches with updates from the out-of-tree
version of sch_cake. The first one is a fix to the fairness scheduling when
dual-mode fairness is enabled. The second patch is an additional feature flag
that allows using fwmark as a tin selector, as a convenience for people who want
to customise tin selection. The third patch is just a cleanup to the tin
selection logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With more modes added the logic in cake_select_tin() was getting a bit
hairy, and it turns out we can actually simplify it quite a bit. This also
allows us to get rid of one of the two diffserv parsing functions, which
has the added benefit that already-zeroed DSCP fields won't get re-written.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add flag 'FWMARK' to enable use of firewall connmarks as tin selector.
The connmark (skbuff->mark) needs to be in the range 1->tin_cnt ie.
for diffserv3 the mark needs to be 1->3.

Background

Typically CAKE uses DSCP as the basis for tin selection.  DSCP values
are relatively easily changed as part of the egress path, usually with
iptables & the mangle table, ingress is more challenging.  CAKE is often
used on the WAN interface of a residential gateway where passthrough of
DSCP from the ISP is either missing or set to unhelpful values thus use
of ingress DSCP values for tin selection isn't helpful in that
environment.

An approach to solving the ingress tin selection problem is to use
CAKE's understanding of tc filters.  Naive tc filters could match on
source/destination port numbers and force tin selection that way, but
multiple filters don't scale particularly well as each filter must be
traversed whether it matches or not. e.g. a simple example to map 3
firewall marks to tins:

MAJOR=$( tc qdisc show dev $DEV | head -1 | awk '{print $3}' )
tc filter add dev $DEV parent $MAJOR protocol all handle 0x01 fw action skbedit priority ${MAJOR}1
tc filter add dev $DEV parent $MAJOR protocol all handle 0x02 fw action skbedit priority ${MAJOR}2
tc filter add dev $DEV parent $MAJOR protocol all handle 0x03 fw action skbedit priority ${MAJOR}3

Another option is to use eBPF cls_act with tc filters e.g.

MAJOR=$( tc qdisc show dev $DEV | head -1 | awk '{print $3}' )
tc filter add dev $DEV parent $MAJOR bpf da obj my-bpf-fwmark-to-class.o

This has the disadvantages of a) needing someone to write & maintain
the bpf program, b) a bpf toolchain to compile it and c) needing to
hardcode the major number in the bpf program so it matches the cake
instance (or forcing the cake instance to a particular major number)
since the major number cannot be passed to the bpf program via tc
command line.

As already hinted at by the previous examples, it would be helpful
to associate tins with something that survives the Internet path and
ideally allows tin selection on both egress and ingress.  Netfilter's
conntrack permits setting an identifying mark on a connection which
can also be restored to an ingress packet with tc action connmark e.g.

tc filter add dev eth0 parent ffff: protocol all prio 10 u32 \
	match u32 0 0 flowid 1:1 action connmark action mirred egress redirect dev ifb1

Since tc's connmark action has restored any connmark into skb->mark,
any of the previous solutions are based upon it and in one form or
another copy that mark to the skb->priority field where again CAKE
picks this up.

This change cuts out at least one of the (less intuitive &
non-scalable) middlemen and permit direct access to skb->mark.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CAKE host fairness does not work well with TCP flows in dual-srchost and
dual-dsthost setup. The reason is that ACKs generated by TCP flows are
classified as sparse flows, and affect flow isolation from other hosts. Fix
this by calculating host_load based only on the bulk flows a host
generates. In a hash collision the host_bulk_flow_count values must be
decremented on the old hosts and incremented on the new ones *if* the queue
is in the bulk set.
Reported-by: Pete Heist <peteheist@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Harini Katakam says:

====================
Macb power management support for ZynqMP

This series adds support for macb suspend/resume with system power down.
In relation to the above, this series also updates mdio_read/write
function for PM and adds tsu clock management.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.

Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add runtime pm functions and move clock handling there.
Add runtime PM calls to mdio functions to allow for active mdio bus.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TSU clock needs to be enabled/disabled as per support in devicetree
and it should also be controlled during suspend/resume (WOL has no
dependency on this clock).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the while loop in MDIO read/write functions with a timeout.
In addition, add a check for MDIO bus busy before initiating a new
operation as well to make sure there is no ongoing MDIO operation.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tristram Ha says:

====================
net: dsa: microchip: add KSZ9893 switch support

This series of patches is to modify the KSZ9477 DSA driver to support
running KSZ9893 switch.

The KSZ9893 switch is similar to KSZ9477 except the ingress tail tag has
1 byte instead of 2 bytes.  The XMII register that governs the MAC
communication also has different register definitions.

v1
- Put KSZ9893 tagging in separate patch
- Remove other switch support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add KSZ9893 switch support in KSZ9477 driver.  This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.

The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes.  The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document additional Microchip KSZ9477 family switches.

Show how KSZ8565 switch should be configured as the host port is port 7
instead of port 5.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-03-01

This series adds multipath offload support and contains some small updates
to mlx5 driver.

Multipath offload support from Roi Dayan:

We are going to track SW multipath route and related nexthops and reflect
that as port affinity to the HW.

1) Some patches are preparation.
2) add the multipath mode and fib events handling.
3) add support to handle offload failure for net error, i.e.
port down.
4) Small updates to match the behavior of multipath

Two small updates from Eran Ben Elisha,
5) Make a function static
6) Update PCIe supported devices list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for net-next:

1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
   After this change, we can remove list of extensions too to simplify this
   codebase.

2) Update amanda conntrack helper to support v3.4, from Florian Tham.

3) Get rid of the obsolete BUGPRINT macro in ebtables, from
   Florian Westphal.

4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
   From Florian Westphal.

5) Patchset to remove nf_nat_l3proto structure to get rid of
   indirections, from Florian Westphal.

6) Skip unnecessary conntrack timeout updates in case the value is
   still the same, also from Florian Westphal.

7) Remove unnecessary 'fall through' comments in empty switch cases,
   from Li RongQing.

8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.

9) Incorrect logic to deactivate path of fixed size hashtable sets,
   element was being tested to self.

10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
    keys.

11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.

12) Enter close state in conntrack if RST matches exact sequence number,
    from Florian Westphal.

13) Initialize dst_cache in tunnel extension, from wenxu.

14) Pass protocol as u16 to xt_check_match and xt_check_target, from
    Li RongQing.

15) SCTP header is granted to be in a linear area from IPVS NAT handler,
    from Xin Long.

16) Don't steal packets coming from slave VRF device from the
    ip_sabotage_in() path, from David Ahern.

17) Fix unsafe update of basechain stats, from Li RongQing.

18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
    modulo operation as bitwise AND, from Li RongQing.

19) Use device_attribute instead of internal definition in the IDLETIMER
    target, from Sami Tolvanen.

20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2019-03-02

Here's one more bluetooth-next pull request for the 5.1 kernel:

 - Added support for MediaTek MT7663U and MT7668U UART devices
 - Cleanups & fixes to the hci_qca driver
 - Fixed wakeup pin behavior for QCA6174A controller

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the support of enabling MT7663U and MT7668U Bluetooth function
running on the top of btmtkuart driver.

There are a few differences between MT766[3,8]U and MT7622 where
MT766[3,8]U are standalone devices based on UART transport while MT7622
bluetooth is a built-in device on MediaTek SoC communicating with the host
through BTIF serial transport. Thus, extra setup sequence is necessary
for these standalone devices such as remote regulator and reset control via
GPIO, baud rate changing handshake between the host and device and so on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Update binding document with adding support of MT7663U and MT7668U UART
devices to mediatek-bluetooth.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The current 300ms delay after a baudrate change is extremely long.
For WCN3990 it is sufficient to wait 10ms after the baudrate change
request has been sent over the wire.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Merge tag 'wireless-drivers-next-for-davem-2019-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.1

Last set of patches. A new hardware support for mt76 otherwise quite
normal.

Major changes:

mt76

* add driver for MT7603E/MT7628

ath10k

* more preparation for SDIO support

wil6210

* support up to 20 stations in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If register_netdev() is failed to register sitn->fb_tunnel_dev,
it will go to err_reg_dev and forget to free netdev(sitn->fb_tunnel_dev).

BUG: memory leak
unreferenced object 0xffff888378daad00 (size 512):
  comm "syz-executor.1", pid 4006, jiffies 4295121142 (age 16.115s)
  hex dump (first 32 bytes):
    00 e6 ed c0 83 88 ff ff 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
backtrace:
    [<00000000d6dcb63e>] kvmalloc include/linux/mm.h:577 [inline]
    [<00000000d6dcb63e>] kvzalloc include/linux/mm.h:585 [inline]
    [<00000000d6dcb63e>] netif_alloc_netdev_queues net/core/dev.c:8380 [inline]
    [<00000000d6dcb63e>] alloc_netdev_mqs+0x600/0xcc0 net/core/dev.c:8970
    [<00000000867e172f>] sit_init_net+0x295/0xa40 net/ipv6/sit.c:1848
    [<00000000871019fa>] ops_init+0xad/0x3e0 net/core/net_namespace.c:129
    [<00000000319507f6>] setup_net+0x2ba/0x690 net/core/net_namespace.c:314
    [<0000000087db4f96>] copy_net_ns+0x1dc/0x330 net/core/net_namespace.c:437
    [<0000000057efc651>] create_new_namespaces+0x382/0x730 kernel/nsproxy.c:107
    [<00000000676f83de>] copy_namespaces+0x2ed/0x3d0 kernel/nsproxy.c:165
    [<0000000030b74bac>] copy_process.part.27+0x231e/0x6db0 kernel/fork.c:1919
    [<00000000fff78746>] copy_process kernel/fork.c:1713 [inline]
    [<00000000fff78746>] _do_fork+0x1bc/0xe90 kernel/fork.c:2224
    [<000000001c2e0d1c>] do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290
    [<00000000ec48bd44>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<0000000039acff8a>] 0xffffffffffffffff
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c39 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calculating the multipath hash for input routes the flow info is
not available and therefore should not be used.

Fixes: 24ba1440 ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Cc: wenxu <wenxu@ucloud.cn>
Acked-by: wenxu <wenxu@ucloud.cn>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: fixes and improvements

This series aims to improve the Marvell PPv2 driver and to fix various
issues we encountered while testing the ports in many different
configurations. The series is based on top of Russell PPv2 phylink
rework and improvement.

I'm not sending a v2 of the previous fixes series as half the patches
are not the same and lots of development happened in between.

While this series contains fixes, it's sent to net-next as it is based
on top of Russell patches that were merged into net-next. I'm also
aiming at net-next as the series reworks critical paths of the PPv2
driver, such as the reset handling of various blocks, to let more weeks
for users to tests and for possible fixes to be sent before it lands
into a stable kernel version.

The series is divided into three parts:

- Patches 1 to 3 are cosmetic changes, sent alongside the series, as I
  saw these small issues while working on this.

- Patches 5 to 8 are fixing (or improving) individual issues that we
  found while testing PPv2.1 and PPv2.2 ports while using various
  interfaces.

  Notable fixes are we support back RGMII interfaces (on both PPv2.1 and
  PPv2.2), as their support was broken by previous patches. We also
  reworked the RXQ computation as the RXQ assignment was not checking
  the maximum number of RXQ available, and was broken for PPv2.1.

- As discussed in a previous fixes series, patches 9 to 15 rework the
  way blocks are set in reset in the PPv2 engine (plus related changes).

  There are four blocks we want to control the reset status: two MAC
  (GMAC and XLG MAC) and two PCS (MPCS and XPCS). The XLG MAC is used
  for 10G connexions and uses the MPCS or the XPCS depending on the mode
  used (10GKR / XAUI / RXAUI) and the GMAC is used for the other modes.

  The idea is to set all blocks in reset by default, and when not used,
  and to de-assert the reset only when a block is used. There are four
  cases to take in account:

  1. Boot time: all four blocks should be put in reset, as we do not
     know their initial state (configured by the firmware/bootloader).

  2. Link up: only the blocks used by a given mode should be put out of
     reset (eg. 10GKR uses the XLG MAC and the MPCS).

  3. Mode reconfiguration: some ports may support mode reconfiguration,
     and switching between the GMAC and the XLG MAC (or between the two
     PCS). All blocks should be put in reset, and only the one used
     should be put out of reset.

  4. Link down: all four blocks are put in reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds calls in the stop() helper to ensure both MACs and
both PCS blocks are set in reset when the user manually sets a port
down. This is done so that we have the exact same block reset states at
boot time and when a port is set down.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets both the XPCS and MPCS blocks in reset when they aren't
used. This is done both at boot time and when reconfiguring a port mode.
The advantage now is that only the PCS used is set out of reset when the
port is configured (10GKR uses the MCPS while RXAUI uses the XPCS).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes sure both PPv2 MACs (GMAC + XLG MAC) are set in reset
while a port is reconfigured. This is done so that we make sure a MAC is
in a reset state when not used, as only one of the two will be set out
of reset after the port is configured properly.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reworks the way the XLG MAC is set in reset: the XLG MAC is
set in reset at probe time and taken out of this state only when used.
The idea is to move forward a situation where only the blocks used are
taken out of reset. This also has the effect to handle the GMAC and the
XLG MAC in a similar way (the GMAC already is set in reset at boot
time).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch force the XLG MAC link state in the phylink link_up() and
link_down() helpers when not using in-band auto-negotiation. This mimics
what's already done for the GMAC and follows what's advised in the
phylink documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves the XLG configuration function, to only update the
XLG configuration register when a change is needed. This helps not
writing over and over the same XLG configuration each time phylink
request the MAC to be configured. This mimics the GMAC configuration
function.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies the port_disable() helper to always disable both the
GMAC and the XLG MAC when called. At boot time we do not know of a port
was enabled in the firmware/bootloader, and if so what mode was used
(hence which of the two MACs was used).

This also help in implementing a logic where all blocks are disabled
when not used, and only enabled regarding the current mode used on a
given port.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>