* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (27 commits)
  [POWERPC] 83xx: Update mpc8349emitx(gp) defconfig for USB
  [POWERPC] 83xx: Update mpc832x_rdb_defconfig to enable MMC-over-SPI
  [POWERPC] 83xx: MPC832x RDB - remove spidev stub, use mmc_spi
  [POWERPC] 8xxx: MDS board RTC fixes
  [POWERPC] Fix 8xx build breakage due to _tlbie changes
  [POWERPC] Fix device tree interrupt map for Freescale ULI1575 boards
  [POWERPC] Fix possible division by zero in scaled time accounting
  [POWERPC] spufs: Fix context destroy vs /spu readdir race
  [POWERPC] Fix RTAS os-term usage on kernel panic
  [POWERPC] 83xx: Handle mpc8360 rev. 2.1 RGMII timing erratum
  [POWERPC] Document rgmii-rxid and rgmii-txid phy-connection-types
  [POWERPC] 83xx: Fix 2nd UCC entry in mpc832x_mds.dts
  [POWERPC] 83xx: mpc832x mds: Fix board PHY reset code
  [POWERPC] Fix potential NULL dereference
  [POWERPC] vdso: Fixes for cache block sizes
  [POWERPC] pasemi: Don't reset mpic at boot
  [POWERPC] Fix kmalloc alignment on non-coherent DMA platforms
  [POWERPC] Fix build failure on legacy iSeries
  [POWERPC] 4xx: Use virtual PVR value to init FPU on arch/ppc 440EP
  [POWERPC] 4xx: UIC add mask_ack callback
  ...

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9416Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] vpe: Add missing "space"
  [MIPS] Compliment va_start() with va_end().
  [MIPS] IP22: Fix broken eeprom access by using __raw_readl/__raw_writel
  [MIPS] IP22: Fix broken EISA interrupt setup by switching to generic i8259
  [MIPS] 64-bit Sibyte kernels need DMA32.
  [MIPS] Only build r4k clocksource for systems that work ok with it.
  [MIPS] Handle R4000/R4400 mfc0 from count register.
  [MIPS] Fix possible hang in LL/SC futex loops.
  [MIPS] Fix context DSP context / TLS pointer switching bug for new threads.
  [MIPS] IP32: More interrupt renumbering fixes.
  [MIPS] time: MIPSsim's plat_time_init doesn't need to be irq safe.
  [MIPS] time: Fix negated condition in cevt-r4k driver.
  [MIPS] Fix pcspeaker build.

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa:
  [ALSA] version 1.0.15
  [ALSA] emu10k1 - Check value ranges in ctl callbacks
  [ALSA] emu10k1: Add mixer controls parameter checking.
  [ALSA] fix private data pointer calculation in CS4270 driver
  [ALSA] portman2x4 - Fix probe error
  [ALSA] ca0106 - Fix write proc assignment
  [ALSA] s3c2443-ac97: compilation fix
  [ALSA] hda-codec - Revert volume knob controls in STAC codecs
  [ALSA] ca0106 - Check value range in ctl callbacks
  [ALSA] hda-codec - Check PINCAP only for PIN widgets
  [ALSA] mpu401: fix recursive locking in timer
  [ALSA] cmipci: fix FLINKON/OFF bits
  [ALSA] hda-codec - Disable shared stream on AD1986A

For a kernel built with "make ARCH=x86" the following system
information is displayed when running the new kernel

    $ uname -m
    x86

On some i386 systems (e.g. K7) we even have the following information

    $ uname -m
    x66

This is weird. The usual information for "uname -m" should be "x86_64"
on 64-bit and "i386" or "i686" on 32-bit.

This patch fixes the issue by setting UTS_MACHINE to "i386" for 32-bit
kernel builds and to "x86_64" for 64-bit kernel builds. I.e., "x86"
won't be used for UTS_MACHINE anymore.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Sibyte SOCs only have 32-bit PCI.  Due to the sparse use of the address
space only the first 1GB of memory is mapped at physical addresses
below 1GB.  If a system has more than 1GB of memory 32-bit DMA will
not be able to reach all of it.

For now this patch is good enough to keep Sibyte users happy but it seems
eventually something like swiotlb will be needed for Sibyte.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all.  This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The R4000 and R4400 have an errata where if the cp0 count register is read
in the exact moment when it matches the compare register no interrupt will
be generated.

This bug may be triggered if the cp0 count register is being used as
clocksource and the compare interrupt as clockevent.  So a simple
workaround is to avoid using the compare for both facilities on the
affected CPUs.

This is different from the workaround suggested in the old errata documents;
at some opportunity probably the official version should be implemented
and tested.  Another thing to find out is which processor versions
exactly are affected.  I only have errata documents upto R4400 V3.0
available so for the moment the code treats all R4000 and R4400 as broken.

This is potencially a problem for some machines that have no other decent
clocksource available; this workaround will cause them to fall back to
another clocksource, worst case the "jiffies" source.

The LL / SC loops in __futex_atomic_op() have the usual fixups necessary
for memory acccesses to userspace from kernel space installed:

        __asm__ __volatile__(
        "       .set    push                            \n"
        "       .set    noat                            \n"
        "       .set    mips3                           \n"
        "1:     ll      %1, %4  # __futex_atomic_op     \n"
        "       .set    mips0                           \n"
        "       " insn  "                               \n"
        "       .set    mips3                           \n"
        "2:     sc      $1, %2                          \n"
        "       beqz    $1, 1b                          \n"
        __WEAK_LLSC_MB
        "3:                                             \n"
        "       .set    pop                             \n"
        "       .set    mips0                           \n"
        "       .section .fixup,\"ax\"                  \n"
        "4:     li      %0, %6                          \n"
        "       j       2b                              \n"	<-----
        "       .previous                               \n"
        "       .section __ex_table,\"a\"               \n"
        "       "__UA_ADDR "\t1b, 4b                    \n"
        "       "__UA_ADDR "\t2b, 4b                    \n"
        "       .previous                               \n"
        : "=r" (ret), "=&r" (oldval), "=R" (*uaddr)
        : "0" (0), "R" (*uaddr), "Jr" (oparg), "i" (-EFAULT)
        : "memory");

The branch at the end of the fixup code, it goes back to the SC
instruction, no matter if the fault was first taken by the LL or SC
instruction resulting in an endless loop which will only terminate if
the address become valid again due to another thread setting up an
accessible mapping and the CPU happens to execute the SC instruction
successfully which due to the preceeding ERET instruction of the fault
handler would only happen if UNPREDICTABLE instruction behaviour of the
SC instruction without a preceeding LL happens to favor that outcome.
But normally processes are nice, pass valid arguments and we were just
getting away with this.

Thanks to Kaz Kylheku <kaz@zeugmasystems.com> for providing the original
report and a test case.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

A new born thread starts execution not in schedule but rather in
ret_from_fork which results in it bypassing the part of the code to
load a new context written in C which are the DSP context and the
userlocal register which Linux uses for the TLS pointer.  Frequently
we were just getting away with this bug for a number of reasons:

 o Real world application scenarios are very unlikely to use clone or fork
   in blocks of DSP code.
 o Linux by default runs the child process right after the fork, so the
   child by luck will find all the right context in the DSP and userlocal
   registers.
 o So far the rdhwr instruction was emulated on all hardware so userlocal
   wasn't getting referenced at all and the emulation wasn't suffering
   from the issue since it gets it's value straight from the thread's
   thread_info.

Fixed by moving the code to load the context from switch_to() to
finish_arch_switch which will be called by newborn and old threads.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It's running early during the bootup process so interrupts are still off.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

USB support for the 8349itx got added a while back; but the defconfig
never got updated.  This patch adds the appropriate USB config options
to the defconfigs
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Scott Wood <scottwood@freescale.com>
CC: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

mmc_spi has hit the mainline, so we can start using it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Check value ranges in ctl callbacks properly.  This fixes the unexpected
crash due to wrong value assignment.
Also, remove invalid comments in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Fix the calculation of the private_data pointer in the CS4270 driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Reported by Ingo Molnar,
when booting an allyesconfig bzImage kernel the bootup hangs in the
portman2x4 driver (on a box that does not have this hardware), at:
 Pid: 1, comm:              swapper
 EIP: 0060:[<c02f763c>] CPU: 0
 EIP is at parport_pc_read_status+0x4/0x8
  EFLAGS: 00000202    Not tainted  (2.6.23-rc9 #904)
 EAX: f7e57a7f EBX: 00000010 ECX: c2b808c0 EDX: 00000379
 ESI: f7cb8230 EDI: 00000010 EBP: f7cb8230 DS: 007b ES: 007b FS: 0000
 CR0: 8005003b CR2: fff9c000 CR3: 007ec000 CR4: 00000690
 DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
 DR6: ffff0ff0 DR7: 00000400
  [<c04613de>] portman_flush_input+0xde/0x12c
  [<c0461a24>] snd_portman_probe+0x368/0x484
  [<c02fbb8c>] __device_attach+0x0/0x8
  [<c02fce68>] platform_drv_probe+0xc/0x10
  [<c02fba6c>] driver_probe_device+0x74/0x194
  [<c0587174>] klist_next+0x38/0x70
  [<c02fbb8c>] __device_attach+0x0/0x8
  [<c02faea1>] bus_for_each_drv+0x35/0x68
  [<c02fbc22>] device_attach+0x72/0x78
the reason is due to an inconsistent error return code of 1 or 2, while
snd_portman_probe only realizes negative error codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

The driver assigns the write proc callback to read wrongly.
Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

The Samsung S3C24xx uses new architecture file layout in the post 2.6.23
kernel.  This patch fixes include path for the s3c2443-ac97.c.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

Volume knob controls with STAC codecs seem to cause problems with some
devices.  Volumes change very slowly or silent suddenly.  It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>

My changes to _tlbie to fix 4xx unfortunately broke 8xx build in a
couple of places.  This fixes it.

Spotted by Olof Johansson.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.

* 8544 DS:
   - Fix interrupt mask
   - Be explicit about use of INTA for on chip peripherals

* 8572 DS/8641 HPCN:
   - Fix interrupt mask
   - Expand interrupt map for PCI slots to cover all functions
   - Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

If we get no user time and no system time allocated since the last
account_system_vtime, the system to user time ratio estimate can end
up dividing by zero.

This was causing a problem noticed by Balbir Singh.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

We can currently cause an oops by repeatedly creating and destroying
contexts, while doing getdents() calls on the "/spu" directory.

This is due to the context's top-level dentry remaining hashed while
the context is being destroyed.

Fix this by unhashing the context's dentry with the
dentry->d_inode->i_mutex held. This way, we'll hit the check for
d_unhashed in dentry_readdir, and won't be included in the
list of subdirs for /spu.

test: spufs-testsuite:tests/01-spu_create/07-destroy-vs-readdir-race
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early.  Instead,
call it from the machine_reset() call.

This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().

Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero.  Calling os-term
helps keep the hypervisor happy!  We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

If on a rev. 2.1, adjust UCC clock and data timing characteristics
as specified in the rev.2.1 erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

A h/w bug requires we program the PHY in RGMII mode for internal delay
on the receive or transmit side only; document the new property values.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

correct the reg property, remove duplicate io port entry, whitespace fixes.

Thanks to Peter Van Ackeren for pointing this out.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

currently the board-level PHY reset code for the mpc832x MDS messes with
reset configuration words source settings which is plain wrong (it
looks like this board code was cut-n-pasted from the mpc8360 mds code,
which has the PHY reset bits in a different BCSR); this patch points
the PHY reset code to the proper mpc832x mds PHY reset bits in the BCSR.
Signed-off-by: Peter Van Ackeren <peter.vanackeren@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>