An error occurred fetching the project authors.
- 14 Jul, 2010 8 commits
-
-
Felix Fietkau authored
According to documentation, The following chip revisions were never sold: - AR9280 v1.0 - AR9285 v1.0 - AR9285 v1.1 - AR9287 v1.0 Removing initvals specific to these chip revisions saves around 30k in binary size (tested on MIPS). Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kulikov Vasiliy authored
We must call del_airo_dev() before free_netdev() since we call add_airo_dev() exactly after alloc_netdev(). Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When kernel-internal users use cfg80211_get_bss() to get a reference to a BSS struct, they may end up getting one that would have been removed from the list if there had been any userspace access to the list. This leads to inconsistencies and problems. Fix it by making cfg80211_get_bss() ignore BSSes that cfg80211_bss_expire() would remove. Fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2180 Cc: stable@kernel.org Reported-by: Jiajia Zheng <jiajia.zheng@intel.com> Tested-by: Jiajia Zheng <jiajia.zheng@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the issue of running out of buffers/descriptors in the tx path if a STA is deleted while tx status feedback is still pending. The remaining issue is that the skbs of the buffers are not reclaimed, leaving a memory leak. This patch fixes this issue by running the buffers through ath_tx_complete_buf(), ensuring that the pending frames counter is also updated. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rajkumar Manoharan authored
num_sec_wiphy means max secondary wifis that the driver can accomudate. So cancelling wiphy work should be based on the presence of secondary wifis. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pavel Roskin authored
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's never used. Remove corresponding arguments of the functions calculating that value. Original patch by Prarit Bhargava <prarit@redhat.com> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
LED should be ON when the radio is put into FULL SLEEP mode during the idle unassociated state. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 13 Jul, 2010 1 commit
-
- 12 Jul, 2010 31 commits
-
-
Christian Lamparter authored
Michael has been out of the scene for a while now, but despite Michael's absence, p54 is still maintained. Cc: Michael Wu <aluminum.tape@gmail.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
AR5008+ and AR9003 currently use two separate implementations of the ath9k_hw_loadnf function. There are three main differences: - PHY registers for AR9003 are different - AR9003 always uses 3 chains, earlier versions are more selective - The AR9003 variant contains a fix for NF load timeouts This patch merges the two implementations into one, storing the register array in the ath_hw struct. The fix for NF load timeouts is not just relevant for AR9003, but also important for earlier hardware, so it's better to just keep one common implementation. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Occasionally the hardware can send out tx status information with the wrong TID. In that case, the BA status cannot be trusted and the aggregate must be retransmitted. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
If the receive path gets stuck, a full hardware reset is necessary to recover from it. If this happens during a scan, the whole scan might fail, as each channel change bypasses the full reset sequence. Fix this by resetting the fast channel change flag if stopping the receive path fails. This will reduce the number of error messages that look like this: ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
PDADC values were only generated for values surrounding the target index, however not for the target index itself, leading to a minor error in the generated curve. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
On AR9285, the antenna switch configuration register uses more than just 16 bits. Because of an arbitrary mask applied to the EEPROM value that stores this configuration, diversity was broken in some cases, leading to a significant degradation in signal strength. Fix this by changing the callback to return a 32 bit value and remove the arbitrary mask. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
All callback functions are gathered in rt2x00dev->ops except for the callback functions which are used in rt2800lib to acces rt2800pci/usb. Move the priv pointer from rt2x00dev to rt2x00dev->ops and rename it to drv to make it obvious that it is the driver callback structure. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Large parts of the firmware initialization are shared between rt2800pci and rt2800usb. Move this code into rt2800lib. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to TSF_SYNC_ADHOC to better express its purpose and introduce the missing TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes that don't need TSF merging. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Activating the TBTT interrupt when a beacon interval of 0 is configured results in an interrupt storm causing the machine to hang. Hence, initialize the beacon interval to a reasonable default of 100TUs. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Using the set_tim callback without managing the DTIM count and the broad- and multicast buffering in hw, fw or the driver results in wrong DTIM count values being sent out in beacons. Since all PCI drivers fetch new beacons periodically and hence get an updated TIM we can just remove the set_tim callback from these. The rt2x00 USB drivers don't update the beacon periodically and thus rely on the set_tim callback to get a correct TIM for beacon transmission. USB devices still suffer from the DTIM count being wrong under some circumstances but removing the set_tim callback from these would cause more harm then good. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation for further fixes. This shouldn't introduce functional changes. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Updating the beacon on pre tbtt instead of beacondone allows much lower latency in regard to TIM updates. Hence, use the pre tbtt interrupt for updating the beacon in rt2800pci (older devices don't provide a pre tbtt interrupt). Also, add a new driver flag to indicate if a driver has pre tbtt support or not and implement the according behavior in rt2x00lib. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Although mac80211 buffers broad- and mutlicast frames for us in AP mode we still have to send them out after a DTIM beacon. Implement this behavior by sending out the buffered frames when the beacondone interrupt is processed. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Since all rt2x00 PCI drivers use threaded interrupts now we don't need to schedule a work just to update the beacon. The only place where the beacon still gets updated in atomic context is from the set_tim callback. Hence, move the work scheduling there. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Use threaded interrupts for all rt2x00 PCI devices. This has several generic advantages: - Reduce the time we spend in hard irq context - Use non-atmic mac80211 functions for rx/tx Furthermore implementing broad- and multicast buffering will be much easier in process context while maintaining low latency and updating the beacon just before transmission (pre tbtt interrupt) can also be done in process context. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
rt2800_write_beacon is the only function which uses EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols in rt2x00 should however use the GPL restricted export. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Implement watchdog monitoring for USB devices (PCI support can be added later). This will determine if URBs being uploaded to the hardware are actually returning. Both rt2500usb and rt2800usb have shown that URBs being uploaded can remain hanging without being released by the hardware. By using this watchdog, a queue can be reset when this occurs. For rt2800usb it has been tested that the connection is preserved even though this interruption. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Currently vgc_level_reg and vgc_level are equal to eachother, while the purpose of vgc_level_reg is the value last written to the register and is remembered through link tuning resets. The vgc_level is the currently active level, which is reset during link tuning resets. The usage of these variables depends on the drivers, some drivers need both, while others need only one of the two. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
While scanning the link tuner must be disabled. Otherwise it will interfere with receiving all beacons for each channel due to changing sensitivity levels. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING Link tuning support is not only based on EEPROM decisions, but also if the device actually supports it. Currently only rt2500usb doesn't support link tuning because of hardware problems. But rt2800usb is also suspected of having problems with link tuning. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ivo van Doorn authored
The RSSI values in the RXWI descriptor aren't true RSSI values. Instead they are more like the AGC values similar to rt61pci. And as such, it needs the same conversion before it can be passed to rt2x00lib/mac80211. This requires the struct queue_entry to be passed to rt2800_process_rxwi rather then the skb structure which is contained in the queue_entry. This is required to obtain the lna_gain information from the rt2x00_dev structure. This fixes connection problems when using wpa_supplicant which would try to connect to the worst AP's rather then the best ones. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Limit the txpower per rate by the approriate values in the eeprom. This avoids too high txpower values resulting in bad tx performance. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Dan Carpenter authored
In hostap_add_interface() we do: sprintf(dev->name, "%s%s", prefix, name); dev->name has IFNAMSIZ (16) characters. prefix is local->dev->name. name is "wds%d" strlen() returns the number of characters in the string not counting the NULL so if we have a string with 11 characters we get "12345678901wds%d" which is 16 characters and a NULL so we're past the end of the array. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Kulikov Vasiliy authored
We must free priv->eeprom allocated in adm8211_read_eeprom(). Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Dan Carpenter authored
This test is off by one because strlen() doesn't include the NULL terminator. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271 code that was introduced in a recent patch in wireless-testing. Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Existing "ethtool -s ethX wol X" command configures hostsleep parameters, but those are activated only during suspend/resume, there is no way to configure host sleep without actual suspend. This patch adds debugfs command to enable/disable host sleep based on already configured host sleep parameters using wol command. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Ever since mac80211/drivers are no longer fully in charge of keeping track of the auth status, trying to make them do so will fail. Instead of warning and reporting the deauthentication to userspace, cfg80211 must simply ignore it so that spurious deauthentications, e.g. before starting authentication, aren't seen by userspace as actual deauthentications. Cc: stable@kernel.org Reported-by: Paul Stewart <pstew@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-