This is V5 of the SuperH Mobile I2C Controller Driver. A simple Master
only driver for the I2C block included in processors such as sh7343,
sh7722 and sh7723. Tested on a sh7722 MigoR using a rs5c732b rtc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Don't use 0 as NULL pointer.

Spotted by sparse.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Move init_completion to just before i2c transfer.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3385Signed-off-by: Hans Schillstrom <hans.schillstrom@shlsys.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Simply use "depends on BLACKFIN" (which is technically correct) and just
document which machines have the device.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-bfin-twi: Use simpler comment headers and strip out information that is maintained in the scm's log
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Blackfin TWI controller hardware pin should be requested from GPIO port controller
Before BF54x, there is no need to do this. But as long as BF54x and BF52x
are supported by this generic driver, the missing pin mux operation should be
added.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

 - Dynamic alloc the resource of TWI driver data according to board information
 - TWI register read/write accessor based on dynamic regs_base
 - Support TWI0/TWI1 for BF54x
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

 - Create a new mode TWI_I2C_MODE_REPEAT.
 - No change to smbus operation.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

__FUNCTION__ is gcc-specific, use __func__.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Driver for I2C interfaces in master mode on SH7760.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Split the handling of the I2C_RDWR and I2C_SMBUS ioctls to their own
functions. This limits the stack usage, saves one level of indentation
and makes the code more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This patch allows the i2c-ibm_iic driver to be built either as an ocp 
driver or an of_platform driver. This allows it to run under the powerpc 
arch but maintains backward compatibility with the ppc arch.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Change the log levels based on feedback from linxppc-dev.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Tested on a blackfin.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.

Concerning the core struct i2c_algo_pca_data:

- A private data field was added, all hardware dependant data may go here.
  Similar to other algorithms, now a pointer to this data is passed to the
  adapter's functions. In order to make as less changes as possible to the
  ISA-driver, it leaves the private data empty and still only uses its static
  variables.

- A "reset_chip" function pointer was added; such a functionality must come
  from the adapter, not the algorithm.

- use a variable "i2c_clock" instead of a function pointer "get_clock",
  allowing for write access to a default in case a wrong value was supplied.

In the algorithm-file:

- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused

(The state-machine for I2C-communication was not touched.)

In the ISA-driver:

- adapt to new algorithm
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Remove trailing whitespaces to make further patches more readable.  Also remove
an unnecessary UTF-char for simplicity ("us" for microseconds is fine enough).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The algorithm drivers are helper drivers that are selected automatically
as needed. There's no point in listing them in the config menu, it can
only confuse users and waste their time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: Correct capitalization "IntX" -> "INTx"
  IB/ipath: Remove tests of PCI_MSI in ipath_iba7220.c
  IB/ipath: Remove dependency on PCI_MSI || HT_IRQ
  IB/ipath: Build IBA7220 code unconditionally
  IB/ipath: Remove reference to dev->class_dev
  IB/ipath: Fix module parameter description for disable_sma
  RDMA/nes: Remove unneeded function declarations

Fix up conflict in drivers/infiniband/hw/ipath/ipath_verbs.c (by picking
the solution from the infiniband branch)

Match what the PCI specification uses.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The PCI MSI interface is stubbed out properly so that all the
functions just return failure if PCI_MSI=n, so there's no reason to
have "#ifdef CONFIG_PCI_MSI" blocks in ipath_iba7220.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Before IBA7220 support was added, the ipath driver didn't support any
hardware unless PCI_MSI and/or HT_IRQ was enabled.  However, the
IBA7220 can generate INTx interrupts, so it makes sense to allow the
driver to be build even if PCI_MSI=n and HT_IRQ=n.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The new IBA7220 code added a call to ipath_init_iba7220_funcs() that
is compiled unconditionally, but only built the IBA7220 code if
PCI_MSI is enabled.  Fix this by building the IBA7220 file
unconditonally.

This fixes build breakage when PCI_MSI=n, HT_IRQ=y and
INFINIBAND_IPATH=y reported by Ingo Molnar <mingo@elte.hu>:

 drivers/built-in.o: In function `ipath_init_one':
 ipath_driver.c:(.devinit.text+0x1e5bc): undefined reference to `ipath_init_iba7220_funcs'
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/ipath: Remove reference to dev->class_dev                                                        
                                                                                                    
Commit 124b4dcb ("IB/ipath: add calls to new 7220 code and enable in                                
build") inadvertently added core to set dev->class_dev.dev back into                                
ib_ipath.  This is completely redundant since commit 1912ffbb ("IB: Set                             
class_dev->dev in core for nice device symlink"), which removed                                     
class_dev setting from low-level drivers, and also will break the build
when class_dev is removed completely from struct ib_device.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Describe disable_sma parameter with its name rather than the internal
ib_ipath_disable_sma variable name, so that the description shows up
properly in modinfo.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Remove redundant static declarations of functions that are defined
before they are used in the source.
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (26 commits)
  mmc: sdio_ops.c should #include "sdio_ops.h"
  mmc: proper prototypes for mmc_attach_*()
  mmc: make __mmc_release_bus() static
  sdhci: improve no card, no reset quirk
  MMC: OMAP: Do not busy wait for end of command for ever
  MMC: OMAP: Start new commands from work queue instead of irq
  MMC: OMAP: Lazy clock shutdown
  MMC: OMAP: Move failing command abortion to workqueue
  MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
  MMC: OMAP: Check the get_cover_state function pointer if not set
  MMC: OMAP: Using setup_timer instead of init_timer
  MMC: OMAP: Abort stuck commands
  MMC: OMAP: General cleanup for MMC multislot support
  MMC: OMAP: Power functions modified to MMC multislot support
  MMC: OMAP: Fix timeout calculation for MMC multislot support
  MMC: OMAP: New release dma and abort xfer functions
  MMC: OMAP: Add back cover switch support
  MMC: OMAP: Introduce new multislot structure and change driver to use it
  MMC: OMAP: Remove cover switch handling to allow adding multislot support
  MMC: OMAP: Fix the BYTEBLOCK capability removal
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC]: Remove SunOS and Solaris binary support.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
  DOC:  A couple corrections and clarifications in USB doc.
  Generate a slightly more informative error msg for bad HZ
  fix typo "is" -> "if" in Makefile
  ext*: spelling fix prefered -> preferred
  DOCUMENTATION:  Use newer DEFINE_SPINLOCK macro in docs.
  KEYS:  Fix the comment to match the file name in rxrpc-type.h.
  RAID: remove trailing space from printk line
  DMA engine: typo fixes
  Remove unused MAX_NODES_SHIFT
  MAINTAINERS: Clarify access to OCFS2 development mailing list.
  V4L: Storage class should be before const qualifier (sn9c102)
  V4L: Storage class should be before const qualifier
  sonypi: Storage class should be before const qualifier
  intel_menlow: Storage class should be before const qualifier
  DVB: Storage class should be before const qualifier
  arm: Storage class should be before const qualifier
  ALSA: Storage class should be before const qualifier
  acpi: Storage class should be before const qualifier
  firmware_sample_driver.c: fix coding style
  MAINTAINERS: Add ati_remote2 driver
  ...

Fixed up trivial conflicts in firmware_sample_driver.c

* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
  block: fix blk_register_queue() return value
  block: fix memory hotplug and bouncing in block layer
  block: replace remaining __FUNCTION__ occurrences
  Kconfig: clean up block/Kconfig help descriptions
  cciss: fix warning oops on rmmod of driver
  cciss: Fix race between disk-adding code and interrupt handler
  block: move the padding adjustment to blk_rq_map_sg
  block: add bio_copy_user_iov support to blk_rq_map_user_iov
  block: convert bio_copy_user to bio_copy_user_iov
  loop: manage partitions in disk image
  cdrom: use kmalloced buffers instead of buffers on stack
  cdrom: make unregister_cdrom() return void
  cdrom: use list_head for cdrom_device_info list
  cdrom: protect cdrom_device_info list by mutex
  cdrom: cleanup hardcoded error-code
  cdrom: remove ifdef CONFIG_SYSCTL

This patch removes the no longer used export of kmap_atomic_to_page.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

HARD_RESET_NOW() was unused.

And one of the few remaining cli() users.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  SELinux: one little, two little, three little whitespaces, the avc.c saga.
  SELinux: cleanup on isle selinuxfs.c
  changing whitespace for fun and profit: policydb.c
  SELinux: whitespace and formating fixes for hooks.c
  SELinux: clean up printks
  SELinux: sidtab.c whitespace, syntax, and static declaraction cleanups
  SELinux: services.c whitespace, syntax, and static declaraction cleanups
  SELinux: mls.c whitespace, syntax, and static declaraction cleanups
  SELinux: hashtab.c whitespace, syntax, and static declaraction cleanups
  SELinux: ebitmap.c whitespace, syntax, and static declaraction cleanups
  SELinux: conditional.c whitespace, syntax, and static declaraction cleanups
  SELinux: avtab.c whitespace, syntax, and static declaraction cleanups
  SELinux: xfrm.c whitespace, syntax, and static declaraction cleanups
  SELinux: nlmsgtab.c whitespace, syntax, and static declaraction cleanups
  SELinux: netnode.c whitespace, syntax, and static declaraction cleanups
  SELinux: netlink.c whitespace, syntax, and static declaraction cleanups
  SELinux: netlabel.c whitespace, syntax, and static declaraction cleanups
  SELinux: netif.c whitespace, syntax, and static declaraction cleanups

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (42 commits)
  PCI: Change PCI subsystem MAINTAINER
  PCI: pci-iommu-iotlb-flushing-speedup
  PCI: pci_setup_bridge() mustn't be __devinit
  PCI: pci_bus_size_cardbus() mustn't be __devinit
  PCI: pci_scan_device() mustn't be __devinit
  PCI: pci_alloc_child_bus() mustn't be __devinit
  PCI: replace remaining __FUNCTION__ occurrences
  PCI: Hotplug: fakephp: Return success, not ENODEV, when bus rescan is triggered
  PCI: Hotplug: Fix leaks in IBM Hot Plug Controller Driver - ibmphp_init_devno()
  PCI: clean up resource alignment management
  PCI: aerdrv_acpi.c: remove unneeded NULL check
  PCI: Update VIA CX700 quirk
  PCI: Expose PCI VPD through sysfs
  PCI: iommu: iotlb flushing
  PCI: simplify quirk debug output
  PCI: iova RB tree setup tweak
  PCI: parisc: use generic pci_enable_resources()
  PCI: ppc: use generic pci_enable_resources()
  PCI: powerpc: use generic pci_enable_resources()
  PCI: ia64: use generic pci_enable_resources()
  ...

A couple of corrections and clarifications in USB
documentation.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [HWRNG] omap: Minor updates
  [CRYPTO] kconfig: Ordering cleanup
  [CRYPTO] all: Clean up init()/fini()
  [CRYPTO] padlock-aes: Use generic setkey function
  [CRYPTO] aes: Export generic setkey
  [CRYPTO] api: Make the crypto subsystem fully modular
  [CRYPTO] cts: Add CTS mode required for Kerberos AES support
  [CRYPTO] lrw: Replace all adds to big endians variables with be*_add_cpu
  [CRYPTO] tcrypt: Change the XTEA test vectors
  [CRYPTO] tcrypt: Shrink the tcrypt module
  [CRYPTO] tcrypt: Change the usage of the test vectors
  [CRYPTO] api: Constify function pointer tables
  [CRYPTO] aes-x86-32: Remove unused return code
  [CRYPTO] tcrypt: Shrink speed templates
  [CRYPTO] tcrypt: Group common speed templates
  [CRYPTO] sha512: Rename sha512 to sha512_generic
  [CRYPTO] sha384: Hardware acceleration for s390
  [CRYPTO] sha512: Hardware acceleration for s390
  [CRYPTO] s390: Generic sha_update and sha_final
  [CRYPTO] api: Switch to proc_create()

Merge branch 'irq-cleanups-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6

* 'irq-cleanups-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] minor irq handler cleanups
  drivers/char: minor irq handler cleanups
  [PPC] minor irq handler cleanups
  [BLACKFIN] minor irq handler cleanups
  [SPARC] minor irq handler cleanups
  ARM minor irq handler cleanup: avoid passing unused info to irq

Generate a slightly more informative error msg for bad HZ
 in include/linux/jiffies.h
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>