btf__parse_raw and btf__parse_elf return negative error numbers wrapped
in an ERR_PTR, so the extracted value needs to be negated before passing
them to strerror which expects a positive error number.

Before:
  Error: failed to load BTF from .../vmlinux: Unknown error -2

After:
  Error: failed to load BTF from .../vmlinux: No such file or directory
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200525135421.4154-1-tklauser@distanz.chSigned-off-by: Alexei Starovoitov <ast@kernel.org>

Following the introduction of CAP_BPF, and the switch from CAP_SYS_ADMIN
to other capabilities for various BPF features, update the capability
checks (and potentially, drops) in bpftool for feature probes. Because
bpftool and/or the system might not know of CAP_BPF yet, some caution is
necessary:

- If compiled and run on a system with CAP_BPF, check CAP_BPF,
  CAP_SYS_ADMIN, CAP_PERFMON, CAP_NET_ADMIN.

- Guard against CAP_BPF being undefined, to allow compiling bpftool from
  latest sources on older systems. If the system where feature probes
  are run does not know of CAP_BPF, stop checking after CAP_SYS_ADMIN,
  as this should be the only capability required for all the BPF
  probing.

- If compiled from latest sources on a system without CAP_BPF, but later
  executed on a newer system with CAP_BPF knowledge, then we only test
  CAP_SYS_ADMIN. Some probes may fail if the bpftool process has
  CAP_SYS_ADMIN but misses the other capabilities. The alternative would
  be to redefine the value for CAP_BPF in bpftool, but this does not
  look clean, and the case sounds relatively rare anyway.

Note that libcap offers a cap_to_name() function to retrieve the name of
a given capability (e.g. "cap_sys_admin"). We do not use it because
deriving the names from the macros looks simpler than using
cap_to_name() (doing a strdup() on the string) + cap_free() + handling
the case of failed allocations, when we just want to use the name of the
capability in an error message.

The checks when compiling without libcap (i.e. root versus non-root) are
unchanged.

v2:
- Do not allocate cap_list dynamically.
- Drop BPF-related capabilities when running with "unprivileged", even
  if we didn't have the full set in the first place (in v1, we would
  skip dropping them in that case).
- Keep track of what capabilities we have, print the names of the
  missing ones for privileged probing.
- Attempt to drop only the capabilities we actually have.
- Rename a couple variables.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200523010247.20654-1-quentin@isovalent.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>

This is a clean-up for the formatting of the do_help functions for
bpftool's subcommands. The following fixes are included:

- Do not use argv[-2] for "iter" help message, as the help is shown by
  default if no "iter" action is selected, resulting in messages looking
  like "./bpftool bpftool pin...".

- Do not print unused HELP_SPEC_PROGRAM in help message for "bpftool
  link".

- Andrii used argument indexing to avoid having multiple occurrences of
  bin_name and argv[-2] in the fprintf() for the help message, for
  "bpftool gen" and "bpftool link". Let's reuse this for all other help
  functions. We can remove up to thirty arguments for the "bpftool map"
  help message.

- Harmonise all functions, e.g. use ending quotes-comma on a separate
  line.
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200523010751.23465-1-quentin@isovalent.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>

Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-05-31

This series contains updates to the ice driver only.

Brett modifies the driver to allow users to clear a VF's
administratively set MAC address on the PF.  Fixes the driver to
recognize an existing VLAN tag when DMAC/SMAC is enabled in a packet.
Fixes an issue, so that VF's are reset after any VF port VLAN
modifications are made on the PF.  Made sure the register QRXFLXP_CNTXT
is cleared before writing a new value to ensure the previous value is
not passed forward.  Updates the PF to allow the VF to request a reset
as soon as it has been initialized.  Fixes an issue to ensure when a VSI
is created, it uses the current coalesce value, not the default value.

Paul allows untrusted VF's to add 16 filters.

Dan increases the timeout needed after a PFR to allow ample time for
package download.

Chinh adjust the define value for the number of PHY speeds we currently
support.  Changes the driver to ignore EMODE error when configuring the
PHY.

Jesse fixes an issue which was preventing a user from configuring the
interface before bringing it up.

Henry fixes the logic for adding back perfect flows after flow director
filter does a deletion.

Bruce fixes line wrappings to make it more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

fix dereference of nexthop group in fdb nexthop group
update validation path.

Fixes: 1274e1cc ("vxlan: ecmp support for mac fdb entries")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

no point getting compat_cmsghdr field-by-field
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add PFC support

This patch set adds support for Priority Flow Control in DPAA2 Ethernet
devices.

The first patch make the necessary changes so that multiple
traffic classes are configured. The dequeue priority
of the maximum 8 traffic classes is configured to be equal.
The second patch adds a static distribution to said traffic
classes based on the VLAN PCP field. In the future, this could be
extended through the .setapp() DCB callback for dynamic configuration.

Also, add support for the congestion group taildrop mechanism that
allows us to control the number of frames that can accumulate on a group
of Rx frame queues belonging to the same traffic class.

The basic subset of the DCB ops is implemented so that the user can
query the number of PFC capable traffic classes, their state and
reconfigure them if necessary.

Changes in v3:
 - add patches 6-7 which add the PFC functionality
 - patch 2/7: revert to explicitly cast mask to u16 * to not get into
   sparse warnings
Changes in v4:
 - really fix the sparse warnings in 2/7
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.

FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.

Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).

Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.

The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.

Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.

With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.

Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class.  This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.

Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.

Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't export __bcm_phy_enable_rdb_access() and
__bcm_phy_enable_legacy_access() functions. They aren't used outside this
module and it was forgotten to provide a prototype for these functions.
Just make them static for now.

Fixes: 11ecf8c5 ("net: phy: broadcom: add cable test support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tun in IFF_NAPI_FRAGS mode calls napi_gro_frags. Unlike netif_rx and
netif_gro_receive, this expects skb->data to point to the mac layer.

But skb_probe_transport_header, __skb_get_hash_symmetric, and
xdp_do_generic in tun_get_user need skb->data to point to the network
header. Flow dissection also needs skb->protocol set, so
eth_type_trans has to be called.

Ensure the link layer header lies in linear as eth_type_trans pulls
ETH_HLEN. Then take the same code paths for frags as for not frags.
Push the link layer header back just before calling napi_gro_frags.

By pulling up to ETH_HLEN from frag0 into linear, this disables the
frag0 optimization in the special case when IFF_NAPI_FRAGS is used
with zero length iov[0] (and thus empty skb->linear).

Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Petar Penkov <ppenkov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compiling with W=1 gives the following warning:
net/sched/cls_flower.c:731:1: warning: ‘mpls_opts_policy’ defined but not used [-Wunused-const-variable=]

The TCA_FLOWER_KEY_MPLS_OPTS contains a list of
TCA_FLOWER_KEY_MPLS_OPTS_LSE. Therefore, the attributes all have the
same type and we can't parse the list with nla_parse*() and have the
attributes validated automatically using an nla_policy.

fl_set_key_mpls_opts() properly verifies that all attributes in the
list are TCA_FLOWER_KEY_MPLS_OPTS_LSE. Then fl_set_key_mpls_lse()
uses nla_parse_nested() on all these attributes, thus verifying that
they have the NLA_F_NESTED flag. So we can safely drop the
mpls_opts_policy.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Horatiu Vultur says:

====================
bridge: mrp: Add support for MRA role

This patch series extends the MRP with the MRA role.
A node that has the MRA role can behave as a MRM or as a MRC. In case there are
multiple nodes in the topology that has the MRA role then only one node can
behave as MRM and all the others need to be have as MRC. The node that has the
higher priority(lower value) will behave as MRM.
A node that has the MRA role and behaves as MRC, it just needs to forward the
MRP_Test frames between the ring ports but also it needs to detect in case it
stops receiving MRP_Test frames. In that case it would try to behave as MRM.

v2:
 - add new patch that fixes sparse warnings
 - fix parsing of prio attribute
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A node that has the MRA role, it can behave as MRM or MRC.

Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace u16/u32 with be16/be32 in the MRP frame types.
This fixes sparse warnings like:
warning: cast to restricted __be16
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value adapter->rss_conf is stored in DMA memory, and it is assigned
to rssConf, so rssConf->indTableSize can be modified at anytime by
malicious hardware. Because rssConf->indTableSize is assigned to n,
buffer overflow may occur when the code "rssConf->indTable[n]" is
executed.

To fix this possible bug, n is checked after being used.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fl_flow_key structure is around 500 bytes, so having two of them
on the stack in one function now exceeds the warning limit after an
otherwise correct change:

net/sched/cls_flower.c:298:12: error: stack frame size of 1056 bytes in function 'fl_classify' [-Werror,-Wframe-larger-than=]

I suspect the fl_classify function could be reworked to only have one
of them on the stack and modify it in place, but I could not work out
how to do that.

As a somewhat hacky workaround, move one of them into an out-of-line
function to reduce its scope. This does not necessarily reduce the stack
usage of the outer function, but at least the second copy is removed
from the stack during most of it and does not add up to whatever is
called from there.

I now see 552 bytes of stack usage for fl_classify(), plus 528 bytes
for fl_mask_lookup().

Fixes: 58cff782 ("flow_dissector: Parse multiple MPLS Label Stack Entries")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.

New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
  between mac and phy is disabled. Instead phylib is used like in
  other typical Linux drivers. The usage of phylib allows to
  specify fixed-link parameters in the device tree.

. The device tree entry phy-connection-type is supported now with
  the modes RGMII or (G)MII (default).

Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
  configurations with phy. Microchip kindly offered testing
  as soon as the Corona measures allow this.

. All review findings of Andrew Lunn are included

Example:
--------
&pcie {
	status = "okay";

	host@0 {
		reg = <0 0 0 0 0>;

		#address-cells = <3>;
		#size-cells = <2>;

		ethernet@0 {
			compatible = "weyland-yutani,noscom1", "microchip,lan743x";
			status = "okay";
			reg = <0 0 0 0 0>;
			phy-connection-type = "rgmii";

			fixed-link {
				speed = <100>;
				full-duplex;
			};
		};
	};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
devlink: Add support for control packet traps

So far device drivers were only able to register drop and exception
packet traps with devlink. These traps are used for packets that were
either dropped by the underlying device or encountered an exception
(e.g., missing neighbour entry) during forwarding.

However, in the steady state, the majority of the packets being trapped
to the CPU are packets that are required for the correct functioning of
the control plane. For example, ARP request and IGMP query packets.

This patch set allows device drivers to register such control traps with
devlink and expose their default control plane policy to user space.
User space can then tune the packet trap policer settings according to
its needs, as with existing packet traps.

In a similar fashion to exception traps, the action associated with such
traps cannot be changed as it can easily break the control plane. Unlike
drop and exception traps, packets trapped via control traps are not
reported to the kernel's drop monitor as they are not indicative of any
problem.

Patch set overview:

Patches #1-#3 break out layer 3 exceptions to a different group to
provide better granularity. A future patch set will make this completely
configurable.

Patch #4 adds a new trap action ('mirror') that is used for packets that
are forwarded by the device and sent to the CPU. Such packets are marked
by device drivers with 'skb->offload_fwd_mark = 1' in order to prevent
the kernel from forwarding them again.

Patch #5 adds the new trap type, 'control'.

Patches #6-#8 gradually add various control traps to devlink with proper
documentation.

Patch #9 adds a few control traps to netdevsim, which are automatically
exercised by existing devlink-trap selftest.

Patches #10 performs small refactoring in mlxsw.

Patches #11-#13 change mlxsw to register its existing control traps with
devlink.

Patch #14 adds a selftest over mlxsw that exercises all the registered
control traps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Generate packets matching the various control traps and check that the
traps' stats increase accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.

A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:

1. Packets might not need to be marked with 'offload_fwd_mark'. For
   example, if packet was trapped before L2 forwarding

2. Packets might not need to be injected to the kernel's Rx path. For
   example, sampled packets are reported to user space via the psample
   module

Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register two control traps with devlink. The existing selftest at
tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh iterates
over all registered traps and checks that the action of non-drop traps
cannot be changed. Up until now only exception traps were tested, now
control traps will be tested as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add packet traps for packets that are sampled / trapped by ACLs, so that
capable drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add layer 3 control packet traps such as ARP and DHCP, so that capable
device drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add layer 2 control packet traps such as STP and IGMP query, so that
capable device drivers could register them with devlink. Add
documentation for every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This type is used for traps that trap control packets such as ARP
request and IGMP query to the CPU.

Do not report such packets to the kernel's drop monitor as they were not
dropped by the device no encountered an exception during forwarding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The action is used by control traps such as IGMP query. The packet is
flooded by the device, but also trapped to the CPU in order for the
software bridge to mark the receiving port as a multicast router port.
Such packets are marked with 'skb->offload_fwd_mark = 1' in order to
prevent the software bridge from flooding them again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets that hit exceptions during layer 3 forwarding must be trapped to
the CPU for the control plane to function properly. Create a dedicated
group for them, so that user space could choose to assign a different
policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>