When building with -Wmaybe-uninitialized, we get a couple of harmless
warnings about three functions in this new driver that don't look
safe to the compiler:

drivers/pwm/pwm-meson.c: In function 'meson_pwm_get_state':
drivers/pwm/pwm-meson.c:355:26: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c: In function 'meson_pwm_disable':
drivers/pwm/pwm-meson.c:263:13: error: 'enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c: In function 'meson_pwm_apply':
drivers/pwm/pwm-meson.c:231:13: error: 'clk_shift' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c:231:36: error: 'enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/pwm/pwm-meson.c:231:24: error: 'clk_enable' may be used uninitialized in this function [-Werror=maybe-uninitialized]

Specifically, if we have a device with an ID other than 0 or 1,
this would result in undefined behavior. This is currently not
possible, but the compiler cannot be expected to know this.

This patch adds a 'default' clause to let the compiler know
what to do instead, which shuts up the warning and makes the
code slightly more resiliant in case it gets extended to other
identifiers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This includes fixing some Coding Style issues and re-ordering and/or
simplifying a little code.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[thierry.reding@gmail.com: applied some bikeshedding>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Setting up the STI PWM IP as capture only, with zero PWM output devices
is a perfectly valid configuration. It is no longer okay to assume that
there must be at least 1 PWM output device. In this patch we make the
default number of PWM output devices zero and only configure channels
explicitly requested.
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Once a PWM capture has been initiated, the capture call enables a rising
edge detection interrupt, then waits. Once each of the 3 phase changes
have been recorded the thread then wakes. The remaining part of the call
carries out the relevant calculations and returns a structure filled out
with the capture data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Here we're requesting the PWM capture IRQ and supplying the handler that
will be called in the event of an interrupt to handle it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Each PWM capture device is allocated a structure to hold its own state.
During a capture the device may be partaking in one of 3 phases. Initial
(rising) phase change, a subsequent (falling) phase change indicating
end of the duty-cycle phase and finally a final (rising) phase change
indicating the end of the period. The timer value snapshot each event is
held in a variable of the same name, and the phase number (0, 1, 2) is
contained in the index variable. Other device specific information, such
as GPIO pin, the IRQ wait queue and locking is also contained in the
structure. This patch initialises this structure for each of the
available devices.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

ST's PWM IP is supplied by 2 different clocks. One for PWM output and
the other for capture. This patch provides clock handling for the
latter.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This is in preparation for subsequent patches that add support for PWM
capture to this driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

In the original code the clock rate was only obtained during
initialisation; however, the rate may change between then and
its use.  This patch ensures the correct rate is acquired just
before use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Exciting functionality is on the way to this device.  But
before we can add it, we need to do some basic housekeeping
so the additions can be added cleanly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This is to bring the terminology used in the STi PWM driver more
into line with the PWM subsystem.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

In order to support capture of PWM signals a new clock as well as an
interrupt line are required. Furthermore a new property is introduced
that allows the number of capture channels to be specified. Typically
there will be less capture channels than output channels, since all
channels have the latter capability, but only some have support for
capture.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The lpc-18xx driver currently manipulates the pwm_device struct directly
rather than using the pwm_set_chip_data() function. While the current
method may save a clock cycle or two, using the explicit function call
makes it more obvious that data is set to the local chip data pointer.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

H3 PWM controller has same register layout as sun4i driver, so it works
by adding H3 specific data.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-pwm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add support for the PWM controller found in the Amlogic SoCs. This
driver supports the Meson8b and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add bindings for the Amlogic PWM Controller in Meson8b and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

From pwm_samsung_calc_tin(), there is routine to find the lowest divider
possible to generate lower frequency than requested one. But it is
always possible to generate requested frequency with large enough
modulation bits except on s3c24xx, so this patch fixes to use lowest div
for the case. This patch removes following UBSAN warning:

   UBSAN: Undefined behaviour in drivers/pwm/pwm-samsung.c:197:13
   shift exponent 32 is too large for 32-bit type 'long unsigned int'
   [...]
   [<c0670248>] (ubsan_epilogue) from [<c06707b4>] (__ubsan_handle_shift_out_of_bounds+0xd8/0x120)
   [<c06707b4>] (__ubsan_handle_shift_out_of_bounds) from [<c0694b28>] (pwm_samsung_config+0x508/0x6a4)
   [<c0694b28>] (pwm_samsung_config) from [<c069286c>] (pwm_apply_state+0x174/0x40c)
   [<c069286c>] (pwm_apply_state) from [<c0b2e070>] (pwm_fan_probe+0xc8/0x488)
   [<c0b2e070>] (pwm_fan_probe) from [<c07ba8b0>] (platform_drv_probe+0x70/0x150)
   [...]

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Remove all pm_runtime_get_sync() and pm_runtime_put_sync() call as well
as the dummy pm_ops from the pwm-tipwmss driver. No registers are being
modified. The runtime PM still needs to be enabled, so that the runtime
PM framework can take care of enabling/disabling the PWMSS clock when
submodules of PWMSS (ECAP or EHRPWM) call runtime PM APIs. With this
change PWMSS clock goes to idle when none of the submodules are in use.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

While the particular usage in question is likely safe (struct
cros_ec_command is 32-bit aligned, followed by <= 32-bit fields), it's
been suggested this is not a great pattern to follow for the general
case -- for example, if we follow a 'struct cros_ec_command' (which is
32-bit- but not 64-bit-aligned) with a struct that starts with a 64-bit
type (e.g., u64), the compiler may add padding.

Let's add __packed, to inform the compiler of our true intention -- to
have no padding between these struct elements -- and to future proof for
any refactorings that might occur.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Use the mtk_pwm_data struction to define different registers
and add MT2701 specific register operations, such as MT2701
doesn't have commit register, needs to disable double buffer
before writing register, and needs to select manual mode
and use PWM_PERIOD/PWM_HIGH_WIDTH.
Signed-off-by: Weiqing Kong <weiqing.kong@mediatek.com>
[thierry.reding@gmail.com: use of_device_get_match_data()]
[thierry.reding@gmail.com: parameterize more consistently]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Add MT2701 compatible string.
Signed-off-by: Weiqing Kong <weiqing.kong@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

This patch adds suspend-to-RAM support to the Berlin PWM driver.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.
Signed-off-by: David Hsu <davidhsu@google.com>
Fixes: 76abbdde ("pwm: Add sysfs interface")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

The current TWL6030 code for the TWL PWM driver does not reliably disable the
PWM output, as tested with LEDs. The previous commit to that driver introduced
that regression.

However, it does make sense to disable the PWM clock after resetting the PWM,
but for some obscure reason, doing it all at once simply doesn't work.

The TWL6030 datasheet mentions that PWMs have to be disabled in two distinct
steps. However, clearing the clock enable bit in a second step (after issuing a
reset first) does not work.

The only approach that works is the one that was in place before the previous
commit to the driver. It consists in enabling the PWM clock after issuing a
reset. This is what TI kernel trees and production code seem to be using.

However, adding an extra step to disable the PWM clock seems to work reliably,
despite looking quite odd.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull documentation fixes from Jonathan Corbet:
 "Three fixes for the docs build, including removing an annoying warning
  on 'make help' if sphinx isn't present"

* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
  DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
  Documenation: update cgroup's document path
  Documentation/sphinx: do not warn about missing tools in 'make help'

Pull binfmt_misc update from James Bottomley:
 "This update is to allow architecture emulation containers to function
  such that the emulation binary can be housed outside the container
  itself.  The container and fs parts both have acks from relevant
  experts.

  To use the new feature you have to add an F option to your binfmt_misc
  configuration"

From the docs:
 "The usual behaviour of binfmt_misc is to spawn the binary lazily when
  the misc format file is invoked.  However, this doesn't work very well
  in the face of mount namespaces and changeroots, so the F mode opens
  the binary as soon as the emulation is installed and uses the opened
  image to spawn the emulator, meaning it is always available once
  installed, regardless of how the environment changes"

* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
  binfmt_misc: add F option description to documentation
  binfmt_misc: add persistent opened binary handler for containers
  fs: add filp_clone_open API

In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.

So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs updates from Al Viro:
 "Assorted cleanups and fixes.

  In the "trivial API change" department - ->d_compare() losing 'parent'
  argument"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  cachefiles: Fix race between inactivating and culling a cache object
  9p: use clone_fid()
  9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
  vfs: make dentry_needs_remove_privs() internal
  vfs: remove file_needs_remove_privs()
  vfs: fix deadlock in file_remove_privs() on overlayfs
  get rid of 'parent' argument of ->d_compare()
  cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
  affs ->d_compare(): don't bother with ->d_inode
  fold _d_rehash() and __d_rehash() together
  fold dentry_rcuwalk_invalidate() into its only remaining caller

Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull more xfs updates from Dave Chinner:
 "This is the second part of the XFS updates for this merge cycle, and
  contains the new reverse block mapping feature for XFS.

  Reverse mapping allows us to track the owner of a specific block on
  disk precisely.  It is implemented as a set of btrees (one per
  allocation group) that track the owners of allocated extents.
  Effectively it is a "used space tree" that is updated when we allocate
  or free extents.  i.e. it is coherent with the free space btrees we
  already maintain and never overlaps with them.

  This reverse mapping infrastructure is the building block of several
  upcoming features - reflink, copy-on-write data, dedupe, online
  metadata and data scrubbing, highly accurate bad sector/data loss
  reporting to users, and significantly improved reconstruction of
  damaged and corrupted filesystems.  There's a lot of new stuff coming
  along in the next couple of cycles,a nd it all builds in the rmap
  infrastructure.

  As such, it's a huge chunk of new code with new on-disk format
  features and internal infrastructure.  It warns at mount time as an
  experimental feature and that it may eat data (as we do with all new
  on-disk features until they stabilise).  We have not released
  userspace suport for it yet - userspace support currently requires
  download from Darrick's xfsprogs repo and build from source, so the
  access to this feature is really developer/tester only at this point.
  Initial userspace support will be released at the same time kernel
  with this code in it is released.

  The new rmap enabled code regresses 3 xfstests - all are ENOSPC
  related corner cases, one of which Darrick posted a fix for a few
  hours ago.  The other two are fixed by infrastructure that is part of
  the upcoming reflink patchset.  This new ENOSPC infrastructure
  requires a on-disk format tweak required to keep mount times in
  check - we need to keep an on-disk count of allocated rmapbt blocks so
  we don't have to scan the entire btrees at mount time to count them.

  This is currently being tested and will be part of the fixes sent in
  the next week or two so users will not be exposed to this change"

* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
  xfs: move (and rename) the deferred bmap-free tracepoints
  xfs: collapse single use static functions
  xfs: remove unnecessary parentheses from log redo item recovery functions
  xfs: remove the extents array from the rmap update done log item
  xfs: in btree_lshift, only allocate temporary cursor when needed
  xfs: remove unnecesary lshift/rshift key initialization
  xfs: remove the get*keys and update_keys btree ops pointers
  xfs: enable the rmap btree functionality
  xfs: don't update rmapbt when fixing agfl
  xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
  xfs: add rmap btree block detection to log recovery
  xfs: add rmap btree geometry feature flag
  xfs: propagate bmap updates to rmapbt
  xfs: enable the xfs_defer mechanism to process rmaps to update
  xfs: log rmap intent items
  xfs: create rmap update intent log items
  xfs: add rmap btree insert and delete helpers
  xfs: convert unwritten status of reverse mappings
  xfs: remove an extent from the rmap btree
  xfs: add an extent to the rmap btree
  ...

Pull qstr constification updates from Al Viro:
 "Fairly self-contained bunch - surprising lot of places passes struct
  qstr * as an argument when const struct qstr * would suffice; it
  complicates analysis for no good reason.

  I'd prefer to feed that separately from the assorted fixes (those are
  in #for-linus and with somewhat trickier topology)"

* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qstr: constify instances in adfs
  qstr: constify instances in lustre
  qstr: constify instances in f2fs
  qstr: constify instances in ext2
  qstr: constify instances in vfat
  qstr: constify instances in procfs
  qstr: constify instances in fuse
  qstr constify instances in fs/dcache.c
  qstr: constify instances in nfs
  qstr: constify instances in ocfs2
  qstr: constify instances in autofs4
  qstr: constify instances in hfs
  qstr: constify instances in hfsplus
  qstr: constify instances in logfs
  qstr: constify dentry_init_security

Pull mailcap fixlets from Mauro Carvalho Chehab:
 "A small fixup for my and Shuah's entries in .mailcap.

  Basically, those entries were with a syntax that makes
  get_maintainer.pl to do the wrong thing"

* tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  .mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan