The writev based write buffer implementation was far to complex as
in most use cases the write buffer had to be handled anyway.
Simplify the write buffer handling and use mtd->write instead.

From extensive testing no performance impact has been noted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

NDFC NAND Flash controller is embedded in PPC EP44x SoCs.
Add platform driver based support.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Add the data structures necessary to provide platform device support
for NAND
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Replace the chip lock by a the controller lock. For simple drivers a
dummy controller structure is created by the scan code.
This simplifies the locking algorithm in nand_get/release_chip().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Unrolling the loops produces denser and much faster code.
Add a config switch which allows to select the byte order of the
resulting ecc code. The current Linux implementation has a byte
swap versus the SmartMedia specification
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

When filing REF_OBSOLETE nodes, we'd add their size to the global
'dirty_size' count, but then to the eraseblock's 'used_size' count.
That's not clever.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

I added an argument to the real function...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The previous code wouldn't work correctly on architectures which have a
non-empty MODULE_SYMBOL_PREFIX, and this version is neater if slightly
less optimal in the built-in case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The patch below adds support for the NAND device on the Amstrad Delta.
This is a 32MiB 8bit Toshiba device, with the data bus connected to the
OMAP MPUIO pins and ALE, CLE, NCE, NRE, NWE and NWP all connected to the
Delta's latch2 16bit latch.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Well, almost. We'll actually keep a 'TEST_TOTLEN' macro set for now, and keep
doing some paranoia checks to make sure it's all working correctly. But if
TEST_TOTLEN is unset, the size of struct jffs2_raw_node_ref drops from 16
bytes to 12 on 32-bit machines. That's a saving of about half a megabyte of
memory on the OLPC prototype board, with 125K or so nodes in its 512MiB of
flash.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We can't use jffs2_scan_dirty_space() because it doesn't do any locking; it's
only for use at scan time -- hence the 'scan' in the name.

Also, don't allocate refs while we have c->erase_completion_lock held.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We don't allocate this locally any more -- it's given to us and owner by
our caller. Also improve the debug messages a little.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Next step in ongoing campaign to file a struct jffs2_raw_node_ref for every
piece of dirty space in the system, so that __totlen can be killed off....
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

If __totlen is going away, we need to pass the length in separately.
Also stop callers from needlessly setting ref->next_phys to NULL,
since that's done for them... and since that'll also be going away soon.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Make sure we allocate a ref for any dirty space which exists between nodes
which we find in an eraseblock summary.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The incoming ref_totlen() calculation is going to rely on the existence
of nodes which cover all dirty space. We can't just tweak the accounting
data any more; we have to call jffs2_scan_dirty_space() to do it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

To eliminate the __totlen field from struct jffs2_raw_node_ref, we need
to allocate nodes for dirty space instead of just tweaking the accounting
data. Introduce jffs2_scan_dirty_space() in preparation for that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

For RWCOMPAT and ROCOMPAT nodes, we should still allow the mount to
succeed. Just abandon the summary and fall through to the full scan.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

If we had to allocate extra space for the summary node, we weren't
correctly freeing it when jffs2_sum_scan_sumnode() returned nonzero --
which is both the success and the failure case. Only when it returned
zero, which means fall through to the full scan, were we correctly freeing
the buffer.

Document the meaning of those return codes while we're at it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We should preserve these when we come to garbage collect them, not let
them get erased. Use jffs2_garbage_collect_pristine() for this, and make
sure the summary code copes -- just refrain from writing a summary for any
block which contains a node we don't understand.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

It should all be counted as dirty space, not wasted and _definitely_ not
unchecked.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The same sequence of code was repeated in many places, to add a new
struct jffs2_raw_node_ref to an eraseblock and adjust the space accounting
accordingly. Move it out-of-line.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

We were calling ref_totlen() 18 times. Even before that becomes a real
function rather than just a dereference, apparently some compilers still
suck anyway. It'll _certainly_ suck after ref_totlen() becomes more
complicated, so calculate it once and don't rely on CSE.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

This improves the time to mount 512MiB of NAND flash on my OLPC prototype
by about 4%. We used to read the last page of the eraseblock twice -- once
to find the offset of the summary node, and again to actually _read_ the
summary node. Now we read the last page only once, and read more only if
we need to.

We also don't allocate a new buffer just for the summary code -- we use
the buffer which was already allocated for the scan. Better still, if the
'buffer' for the scan is actually just a pointer directly into NOR flash,
we use that too, avoiding the memcpy() which we used to do.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

WARNING: "__moddi3" [drivers/mtd/mtdconcat.ko] undefined!
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

drivers/mtd/devices/docprobe.c: In function `DoC_Probe':
drivers/mtd/devices/docprobe.c:338: warning: assignment from incompatible pointer type
drivers/mtd/devices/docprobe.c:341: warning: assignment from incompatible pointer type

Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Remove forgotten lines from jffs2_scan_eraseblock() which
were unnecessary and may cause problem in some environments.

Thanks to Alexander Belyakov <alexander.belyakov@intel.com>.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Device node major/minor numbers are just stored in the payload of a single
data node. Just extend that to 4 bytes and use new_encode_dev() for it.

We only use the 4-byte format if we _need_ to, if !old_valid_dev(foo).
This preserves backwards compatibility with older code as much as
possible. If we do make devices with major or minor numbers above 255, and
then mount the file system with the old code, it'll just read the first
two bytes and get the numbers wrong. If it comes to garbage-collect it,
it'll then write back those wrong numbers. But that's about the best we
can expect.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: David Woodhouse <dwmw2@infradead.org>

There is a second revision of "mtdconcat NAND/Sibley" patch. I hope
the patch will not get damaged as I'm posting it from gmail account,
thanks to Jorn.

The patch adds previously missing concat_writev(),
concat_writev_ecc(), concat_block_isbad(), concat_block_markbad()
functions to make concatenation layer compatible with Sibley and NAND
chips.

Patch has been cleared from whitespaces, fixed some lines of code as
requested. Also I have added code for alignment check that should
support Jorn's "writesize" patch.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

The following difference was found between the mainline and linux-mips
kernel.  LASAT depends on MTD_CFI.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

In an unrelated MTD commit, a description about the ms02-nv module
got removed from Kconfig.  While I personally agree with this
removal, the module maintainer (Maciej W. Rozycki) would like to
see it added back.  In the absense of any consistency regarding
Kconfig descriptions his wish should be followed.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>