AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.

To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for suspend/resume in if_spi.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver adds WiFi support for Marvell 802.11n based chipsets
with SDIO interface. Currently only SD8787 is supported. More
chipsets will be supported later.

drivers/net/wireless/mwifiex/
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Ramesh Radhakrishnan <rramesh@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Only AR9485 1.1 was sold. This debloats the driver by ~14 KiB.

   text    data     bss     dec     hex filename
 300413     624    1056  302093   49c0d drivers/net/wireless/ath/ath9k/ath9k_hw.ko

   text    data     bss     dec     hex filename
 310285     624    1056  311965   4c29d drivers/net/wireless/ath/ath9k/ath9k_hw-old.ko

$ du -b ath9k_hw*
6210541	ath9k_hw.ko
6225089	ath9k_hw-old.ko

Cc: Bill Wu <bill.wu@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Forbes Tsai <Forbes.Tsai@Atheros.com>
Cc: Jesmine Chen <jesmine.chen@atheros.com>
Cc: Marvian Chen <Hou-hua.Chen@Atheros.com>
Cc: Vivek Natarajan <vivek.natarajan@atheros.com>
Cc: Bernadette Yetso <bernadette.yetso@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Acked-by: Yi-Chen Su <yi-chen.su@atheros.com>
Acked-by: Jeffrey Chung <jeffrey.chung@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211_tx_status iterates over all tx rates the driver reports back
in order to
1) mark tx rates as invalid if the driver cannot have tried that rate
2) find the actually used tx rate for the final retransmission

By leaving the for loop when the first invalid rate index is found we
can move the rates_idx assignment after the loop and therefore save
a few assignments and conditionals.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This workaround called ath_txq_schedule whenever there were still pending
frames for a queue, but the queue depth was zero. Because of its its high
false positive probability (e.g. with paused TIDs) and because it is in
the way of other pending work (AP powersave fixes), it is better to remove
this code entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On some devices the correct MAC address is not in the EEPROM data, but
stored somewhere else.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the ath9k debugfs directory is cleaned up by debugfs_remove_recursive,
there's no point in checking the return code of every single debugfs create
line.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Queue ADDBA requests in respective data queues to avoid ADDBA
requests and the the related data packets (to the same ra/tid)
queued in the hardware to be sent out asynchronously.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the outgoing packet rate to a particular HT station is <=6.5
Mbps, do not attempt to create an ampdu. Also, if the outgoing
rate is legacy rate, do not create an ampdu.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an ampdu stream is on, if the firmware rate adaptation
logic decides that the outgoing packet rate to the station needs
to go below 6.5Mbps (non HT rate), it sends an event indicating that
the ampdu stream needs to be destroyed. Handle this event in the driver
and destroy the ampdu stream so that the rate can go below 6.5Mbps
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specifically, handle ampdu_action and attempt to start a BA
session on receiving the first qos packet from mac80211 for
transmission to a HT sta.  While the BA session is being created,
all the packets belonging to that stream will be dropped to
prevent sequence number mismatch at the recipient.

Contains contributions from:
Yogesh Powar <yogeshp@marvell.com>
Pradeep Nemavat <pnemavat@marvell.com>
Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In particular, we can now add, start, lookup, and remove streams.

Based on work by Nishant Sarmukadam <nishants@marvell.com> and
Pradeep Nemavat <pnemavat@marvell.com>.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We now have two different kinds of queues.  And the number of
AMPDU queues may vary.  So we must be clear about which queues we
are dealing with.  Note that when we report the number of queues
to mac80211, we only report the WMM queues.

Based on work by Yogesh Powar <yogeshp@marvell.com>.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware APIv2 adds the following enhancements:

-- capabilities are reported by the firmware
-- API supports up to 8 dedicated AMPDU streams
-- optional packet timestamping and expiration can be enabled.
   Specifically, packets that are queued in firmware for longer
   than 500ms will be dropped if this option is used.

Based on work by "Nishant Sarmukadam" <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specifically, APIv2 will specify a variable number of AMPDU
queues in the MWL8K_CMD_GET_HW_SPEC.  So init the tx queues after
MWL8K_CMD_GET_HW_SPEC for ap fw.

Also, we make it safe to deinit queues that have not been init'd.
This happens if the mwl8k_get_hw_spec_ap routine fails, for
example.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Took me a minute to figure this out, maybe
it's better documented...
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.

Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.

In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.

Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

By enabling buffered register write for ath9k_htc driver
avoids unnecessary dissociation while rekeying phase under
heavy traffic exchange.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Doing adc gain calibration for AR9287 chips is causing
throughput drops in HT40 mode. Remove ADC Gain from supported
calibration list.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We initialize exit_pending twice.  It's the second initialization which
is correct.  That was added in d745d472 "iwlwifi: cancel scan when
down the device".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
  mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
  mmc: tmio_mmc: Move some defines into a shared header
  mmc: tmio: support aggressive clock gating
  mmc: tmio: fix power-mode interpretation
  mmc: tmio: remove work-around for unmasked SDIO interrupts
  sh: fix SDHI IO address-range
  ARM: mach-shmobile: fix SDHI IO address-range
  mmc: tmio: only access registers above 0xff, if available
  mfd: remove now redundant sh_mobile_sdhi.h header
  sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
  ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
  mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
  sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
  mmc: tmio: split core functionality, DMA and MFD glue
  mmc: tmio: use PIO for short transfers
  mmc: tmio-mmc: Improve DMA stability on sh-mobile
  mmc: fix mmc_app_send_scr() for dma transfer
  mmc: sdhci-esdhc: enable esdhc on imx53
  mmc: sdhci-esdhc: use writel/readl as general APIs
  mmc: sdhci: add the abort CMDTYPE bits definition
  ...

* 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv:
  FRV: Use generic show_interrupts()
  FRV: Convert genirq namespace
  frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
  frv: Convert cpu irq_chip to new functions
  frv: Convert mb93493 irq_chip to new functions
  frv: Convert mb93093 irq_chip to new function
  frv: Convert mb93091 irq_chip to new functions
  frv: Fix typo from __do_IRQ overhaul
  frv: Remove stale irq_chip.end
  FRV: Do some cleanups
  FRV: Missing node arg in alloc_thread_info_node() macro
  NOMMU: implement access_remote_vm
  NOMMU: support SMP dynamic percpu_alloc
  NOMMU: percpu should use is_vmalloc_addr().

* 'stable/bug-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: Use new irq_move functions
  xen: Convert genirq namespace
  xen: fix p2m section mismatches
  xen/p2m: Allocate p2m tracking pages on override
  xen-gntdev: unlock on error path in gntdev_mmap()
  xen-gntdev: return -EFAULT on copy_to_user failure

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: softdog.c: enhancement to optionally invoke panic instead of reboot on timer expiry
  watchdog: fix nv_tco section mismatch
  watchdog: sp5100_tco.c: Check if firmware has set correct value in tcobase.
  watchdog: Convert release_resource to release_region/release_mem_region
  watchdog: s3c2410_wdt.c: Convert release_resource to release_region/release_mem_region

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Fix potential memleak

Merge branch 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (111 commits)
  gpio: ab8500: Mark broken
  genirq: Remove move_*irq leftovers
  genirq: Remove compat code
  drivers: Final irq namespace conversion
  mn10300: Use generic show_interrupts()
  mn10300: Cleanup irq_desc access
  mn10300: Convert genirq namespace
  frv: Use generic show_interrupts()
  frv: Convert genirq namespace
  frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
  frv: Convert cpu irq_chip to new functions
  frv: Convert mb93493 irq_chip to new functions
  frv: Convert mb93093 irq_chip to new function
  frv: Convert mb93091 irq_chip to new functions
  frv: Fix typo from __do_IRQ overhaul
  frv: Remove stale irq_chip.end
  m68k: Convert irq function namespace
  xen: Use new irq_move functions
  xen: Cleanup genirq namespace
  unicore32: Use generic show_interrupts()
  ...

This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)".  If that isn't 1, we have way
  deeper problems than a simple multiplication can fix.   - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.

Cc: <stable@kernel.org> # 38.x
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

Fix the incorrect use of igrab() inside the i_lock in NFS and Ceph‥

If we are already holding the i_lock, we have a reference to the
inode so we can safely use ihold() to gain an extra reference. This
avoids hangs due to lock recursion on the i_lock now that the
inode_lock is gone and igrab() uses the i_lock itself.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  xfrm: Restrict extended sequence numbers to esp
  xfrm: Check for esn buffer len in xfrm_new_ae
  xfrm: Assign esn pointers when cloning a state
  xfrm: Move the test on replay window size into the replay check functions
  netdev: bfin_mac: document TE setting in RMII modes
  drivers net: Fix declaration ordering in inline functions.
  cxgb3: Apply interrupt coalescing settings to all queues
  net: Always allocate at least 16 skb frags regardless of page size
  ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
  net: fix ethtool->set_flags not intended -EINVAL return value
  mlx4_en: Fix loss of promiscuity
  tg3: Fix inline keyword usage
  tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
  net: use CHECKSUM_NONE instead of magic number
  Net / jme: Do not use legacy PCI power management
  myri10ge: small rx_done refactoring
  bridge: notify applications if address of bridge device changes
  ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
  can: c_can: Fix tx_bytes accounting
  can: c_can_platform: fix irq check in probe
  ...

These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>