Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-12-05

This series contains updates to ixgbe and ixgbevf.

Alex provides a couple of patches to cleanup ixgbe.  First cleans up the
page reuse code getting it into a state where all the workarounds needed
are in place as well as cleaning up a few minor oversights such as using
__free_pages instead of put_page to drop a locally allocated page.  Then
cleans up the tail writes for the ixgbe descriptor queues.

Mark Peterson adds support to lookup MAC addresses in Open Firmware or
IDPROM.

Emil provides patches for ixgbe and ixgbevf to fix an issue on rmmod and
to add support for X550 in the VF driver.  First removes the read/write
operations to the CIAA/D registers since it can block access to the PCI
config space and make use of standard kernel functions for accessing the
PCI config space.  Then fixes an issue where the driver has logic to free
up used data in case any of the checks in ixgbe_probe() fail, however
there is a similar set of cleanups that can occur on driver unload in
ixgbe_remove() which can cause the rmmod command to crash.

Don provides the remaining patches in the series to complete the addition
of X550 support into the ixgbe driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves couple of issues in ixgbevf_probe/remove():

1. Fix a case where adapter->state is tested after free_netdev() this is
same as the patch for ixgbe from Daniel Borkmann <dborkman@redhat.com>:
commit b5b2ffc0 ("ixgbe: fix use after free adapter->state test in ixgbe_remove/ixgbe_probe")

2. Move pci_set_drvdata() after all the error checks in ixgbevf_probe() and
then add a check in ixgbevf_probe() to avoid running the cleanup functions
twice in cases where probe failed.

CC: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds initial support for VFs on a new mac - X550.

The patch adds the basic structures and device IDs for the X550 VFs
that would allow the driver to load and pass traffic.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.

This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods.  Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification.  These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the shared code checksum calculation function only
returns a u16 and cannot return an error code. Unfortunately
a variety of errors can happen that completely prevent the
calculation of a checksum. So, change the function return value
from a u16 to an s32 and return a negative value on error, or the
positive checksum value when there is no error.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some X550 procedures will be using CS4227 PHY and need to
perform combined read and write operations.  This patch
adds those methods.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The X550 hardware will use more bits in the mask, so change
the prototypes to match.  This larger mask will require changes
in callers which use the higher bits. Likewise since X550 will
use different semaphore mask values and will use the lan_id
value.  So save these values in the ixgbe_phy_info struct.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since on X550 we use host interface commands to read,write and erase
some commands require more time to complete. So this adds a timeout
parameter to ixgbe_host_interface_command as wells as a return_data
parameter allowing us to return with any data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key.  This patch will enable this functionality
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Accessing the CIAA/D register can block access to the PCI config space.

This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.

In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.

CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the tail writes for the ixgbe descriptor queues.  The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.

It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.

It also cleans up how we clear the descriptor status bits.  Previously they
were zeroed as a part of clearing the hdr_addr.  However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems.  Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared.  As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.

Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When we write the GSO meta-data in tun_get_user we end up advancing
the IO vector twice, thus exhausting the user buffer before we can
finish writing the packet.

Fixes: f5ff53b4 ("{macvtap,tun}_get_user(): switch to iov_iter")
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
introduce rocker switch driver with hardware accelerated datapath api - phase 1: bridge fdb offload

This patchset is just the first phase of switch and switch-ish device
support api in kernel. Note that the api will extend.

So what this patchset includes:
- introduce switchdev api skeleton for implementing switch drivers
- introduce rocker switch driver which implements switchdev api fdb and
  bridge set/get link ndos

As to the discussion if there is need to have specific class of device
representing the switch itself, so far we found no need to introduce that.
But we are generally ok with the idea and when the time comes and it will
be needed, it can be easily introduced without any disturbance.

This patchset introduces switch id export through rtnetlink and sysfs,
which is similar to what we have for port id in SR-IOV. I will send iproute2
patchset for showing the switch id for port netdevs once this is applied.
This applies also for the PF_BRIDGE and fdb iproute2 patches.

iproute2 patches are now available here:
https://github.com/jpirko/iproute2-rocker

For detailed description and version history, please see individual patches.

In v4 I reordered the patches leaving rocker patches on the end of the patchset.

In v5 I only fixed whitespace issues of patch #13

We have a TODO for related items we want to work on in near future:
https://etherpad.wikimedia.org/p/netdev-swdev-todo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Silences various sparse warnings
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rocker ports will use new "swdev" hwmode for bridge port offload policy.
Current supported policy settings are BR_LEARNING and BR_LEARNING_SYNC.
User can turn on/off device port FDB learning and syncing to bridge.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add L2 bridge offloading support to rocker driver.  Here, the Linux bridge
driver is used to collect swdev ports into a tagged (or untagged) VLAN
bridge.  The switchdev will offload from the bridge driver the following L2
bridging functions:

 - Learning of neighbor MAC addresses on VLAN X  Learned mac/vlan is
installed in bridge FDB.  (And removed when device unlearns mac/vlan).
Learning must be turned off on each bridge port to disable the feature in
the bridge driver.

- Flooding of multicast/broadcast and unknown unicast pkts to (STP)
active ports in bridge.  The bridge driver is unaware of the flooding happening
at the device level.  Flooding must be turned off on each bridge port to
disable the feature on the bridge driver.

- STP port state is pushed down to driver/device.  The bridge still processes
STP BDPUs and maintains port STP state (for all VLANs in bridge), but
the driver/device must be notified of port STP state change to program
the device.

Multiple (VLAN) bridges are supported.  The device (implemented per
the OF-DPA spec) must use a portion of the VLAN namespace for
internal VLANs.  Right now, the upper 255 VLANs (0xf00 to 0xffe) are
used as internal VLAN IDs for untagged traffic and are not available
as port VLANs.

The driver uses the following interfaces:

1. To track VLAN add/del on ports in bridge:

.ndo_vlan_rx_add_vid
.ndo_vlan_rx_kill_vid

2. To track port add/del membership in bridge:

NETDEV_CHANGEUPPER netdevice notifier

3. To catch static FDB entries installed on bridge/vlan by user using netlink:

.ndo_fdb_add
.ndo_fdb_del

4. To be notified on port STP state change:

.ndo_switch_port_stp_update

5. To notify bridge driver on learned/forgotten mac/vlans on bridge port:

br_fdb_external_learn_add
br_fdb_external_learn_del
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rocker driver maintains 4 hash tables: flows, groups, FDB, and VLANs.

Flow and group tables track the entries installed to OF-DPA tables,
per the OF-DPA spec.  See OF-DPA spec for full description of fields
in each flow and group table.  New table entries are pushed to the
device with ADD cmd.  Updated entries are pushed to the device with
MOD cmd.  For flow table entries, a crc32 key is made from fields of
the particular field.  For group table entries, the group_id is used
as the key.

The FDB table tracks fdb entries learned by the device or manually
pushed to the bridge by the user.  A crc32 key is made from the
port/mac/vlan tuple for the fdb entry.

The VLAN table tracks the ifindex-to-internal-vlan mapping for
untagged pkts.  On ingress, an untagged pkt is inserted with an
internal VLAN ID based on the input port's current internal VLAN ID.
The input port's internal VLAN will either be referenced by the port's
ifindex, if not bridged, or the containing bridge's ifindex, if
bridged.  Since the ifindex space isn't within a fixed range, uses a
hash table (with ifindex as key) to track internal VLAN ID for a given
ifindex.  The internal VLAN ID range is fixed and currently uses the
upper 255 VLAN IDs, starting at 0xf00.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the first driver to benefit from the switchdev
infrastructure and to implement newly introduced switch ndos. This is a
driver for emulated switch chip implemented in qemu:
https://github.com/sfeldma/qemu-rocker/

This patch is a result of joint work with Scott Feldman.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow brport device to return current brport flags set on port.  Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current hwmode settings are "vepa" or "veb".  These are for NIC interfaces
with basic bridging function offloaded to HW.  Add new "swdev" for full
switch device offloads.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This policy flag controls syncing of learned FDB entries to bridge's FDB.  If
on, FDB entries learned on bridge port device will be synced.  If off, device
may still learn new FDB entries but they will not be synced with bridge's FDB.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device.  This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).

This is equivalent to the device running these cmds:

  bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master

This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.

Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current name might seem that this actually offloads the fdb entry to
hw. So rename it to clearly present that this for hardware address
addition/removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 9c62a68d ("netpoll:
Remove dead packet receive code (CONFIG_NETPOLL_TRAP)") this
Kconfig option was removed.  So remove references to it from
all defconfigs as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver uses ip_out_local() and ip6_route_output() which are
defined only if CONFIG_INET and CONFIG_IPV6 are enabled respectively.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>