During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).

Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.

Here is the race:

CPU 0                                   CPU1

- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
                                - acquires the mutex_lock
                                - allocates rdma response queues
                                - if FULL_INIT_DONE set,
                                  tell uP to route ctrl queue compl
                                  to rdma rspq
                                - relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock

This patch fixes the above issue.

Fixes: e7519f99('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-06-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Here's just the fix for that ancient bug:
 * remove wext calling ndo_do_ioctl, since nobody needs
   that now and it makes the type change easier
 * use struct iwreq instead of struct ifreq almost everywhere
   in wireless extensions code
 * copy only struct iwreq from userspace in dev_ioctl for the
   wireless extensions, since it's smaller than struct ifreq
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Same as ip_gre, geneve and vxlan, use key->tos as traffic class value.

CC: Peter Dawson <petedaws@gmail.com>
Fixes: 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets”)
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the existing dn_route.c code, dn_route_output_slow() takes
dst->__refcnt before calling dn_insert_route() while dn_route_input_slow()
does not take dst->__refcnt before calling dn_insert_route().
This makes the whole routing code very buggy.
In dn_dst_check_expire(), dnrt_free() is called when rt expires. This
makes the routes inserted by dn_route_output_slow() not able to be
freed as the refcnt is not released.
In dn_dst_gc(), dnrt_drop() is called to release rt which could
potentially cause the dst->__refcnt to be dropped to -1.
In dn_run_flush(), dst_free() is called to release all the dst. Again,
it makes the dst inserted by dn_route_output_slow() not able to be
released and also, it does not wait on the rcu and could potentially
cause crash in the path where other users still refer to this dst.

This patch makes sure both input and output path do not take
dst->__refcnt before calling dn_insert_route() and also makes sure
dnrt_free()/dst_free() is called when removing dst from the hash table.
The only difference between those 2 calls is that dnrt_free() waits on
the rcu while dst_free() does not.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When __ip6_tnl_rcv fails, the tun_dst won't be freed, so call
dst_release to free it in error code path.

Fixes: 8d79266b ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
CC: Alexei Starovoitov <ast@fb.com>
Tested-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ip_tunnel_rcv fails, the tun_dst won't be freed, so call
dst_release to free it in error code path.

Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Tested-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox mlx5 fixes 2017-06-14

This series contains some fixes for the mlx5 core and netdev driver.

Please pull and let me know if there's any problem.

For -stable:
("net/mlx5: Wait for FW readiness before initializing command interface") kernels >= 4.4
("net/mlx5e: Fix timestamping capabilities reporting") kernels >= 4.5
("net/mlx5e: Avoid doing a cleanup call if the profile doesn't have it") kernels >= 4.9
("net/mlx5e: Fix min inline value for VF rep SQs") kernels >= 4.11

The "net/mlx5e: Fix min inline .." (a oneliner patch) doesn't cleanly apply
to 4.11, it hits a contextual conflict and can be easily resolved by:
+       mlx5_query_min_inline(mdev, &priv->params.tx_min_inline_mode);
to the end of mlx5e_build_rep_netdev_priv. Note the 2nd parameter of
mlx5_query_min_inline is slightly different from the original one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.

Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.

Fixes: 26e59d80 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the firmware API is partial and allows to offload only
the dscp part of the tos, also, ipv6 support isn't there yet.

As such, remove the offloading option of ipv4 dscp till the FW
APIs are more comprehensive.

Fixes: d79b6df6 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.

To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.

Fixes: 7768d197 ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Mohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.

This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.

Fixes: a6f402e4 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"

Fixes: ef9814de ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.

If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address.  This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.

Fixes: e3297246 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The referenced file dsa.txt is located at
Documentation/devicetree/bindings/net/dsa/dsa.txt
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_for_each_transport, pos is used to save how many objs it has
dumped. Now it gets the last obj by sctp_transport_get_idx, then gets
the next obj by sctp_transport_get_next.

The issue is that in the meanwhile if some objs in transport hashtable
are removed and the objs nums are less than pos, sctp_transport_get_idx
would return NULL and hti.walker.tbl is NULL as well. At this moment
it should stop hti, instead of continue getting the next obj. Or it
would cause a NULL pointer dereference in sctp_transport_get_next.

This patch is to pass pos + 1 into sctp_transport_get_idx to get the
next obj directly, even if pos > objs nums, it would return NULL and
stop hti.

Fixes: 626d16f5 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes CVE-2017-7482.

When a kerberos 5 ticket is being decoded so that it can be loaded into an
rxrpc-type key, there are several places in which the length of a
variable-length field is checked to make sure that it's not going to
overrun the available data - but the data is padded to the nearest
four-byte boundary and the code doesn't check for this extra.  This could
lead to the size-remaining variable wrapping and the data pointer going
over the end of the buffer.

Fix this by making the various variable-length data checks use the padded
length.
Reported-by: 石磊 <shilei-c@360.cn>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.c.dionne@auristor.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.

The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.

        if (!delayed_work_pending(&ifp->dad_work))
                in6_ifa_hold(ifp);
                    <--------------[1]
        mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);

An use-after-free issue can be caused by this.

Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.

As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.

Note that this patch did not choose to fix it with:

  if (!mod_delayed_work(delay))
          in6_ifa_hold(ifp);

As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) The netlink attribute passed in to dev_set_alias() is not
    necessarily NULL terminated, don't use strlcpy() on it. From
    Alexander Potapenko.

 2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
    Borkmann.

 3) Correct the release of netdevs and driver private data in certain
    circumstances.

 4) Sanitize netlink message length properly in decnet, from Mateusz
    Jurczyk.

 5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
    Yuval Mintz.

 6) Hash secret is never initialized in ipv6 ILA translation code, from
    Arnd Bergmann. I guess those clang warnings about unused inline
    functions are useful for something!

 7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.

 8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
    and CAIF. From Mateusz Jurczyk.

 9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
    Molitor.

10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
    Johannes Berg.

11) Fix locking in sctp_for_each_endpoint(), from Xin Long.

12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.

13) Fix use after free in ip_mc_clear_src(), from WANG Cong.

14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
    Jesper Dangaard Brouer.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
  i40e: Fix a sleep-in-atomic bug
  net: don't global ICMP rate limit packets originating from loopback
  net/act_pedit: fix an error code
  net: update undefined ->ndo_change_mtu() comment
  net_sched: move tcf_lock down after gen_replace_estimator()
  caif: Add sockaddr length check before accessing sa_family in connect handler
  qed: fix dump of context data
  qmi_wwan: new Telewell and Sierra device IDs
  net: phy: Fix MDIO_THUNDER dependencies
  netconsole: Remove duplicate "netconsole: " logging prefix
  igmp: acquire pmc lock for ip_mc_clear_src()
  r8152: give the device version
  net: rps: fix uninitialized symbol warning
  mac80211: don't send SMPS action frame in AP mode when not needed
  mac80211/wpa: use constant time memory comparison for MACs
  mac80211: set bss_info data before configuring the channel
  mac80211: remove 5/10 MHz rate code from station MLME
  mac80211: Fix incorrect condition when checking rx timestamp
  mac80211: don't look at the PM bit of BAR frames
  i40e: fix handling of HW ATR eviction
  ...

Pull crypto fix from Herbert Xu:
 "This fixes a bug on sparc where we may dereference freed stack memory"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: Work around deallocated stack frame reference gcc bug on sparc.

Pull ACPI fixes from Rafael Wysocki:
 "These revert an ACPICA commit from the 4.11 cycle that causes problems
  to happen on some systems and add a protection against possible kernel
  crashes due to table reference counter imbalance.

  Specifics:

   - Revert a 4.11 ACPICA change that made assumptions which are not
     satisfied on some systems and caused the enumeration of resources
     to fail on them (Rafael Wysocki).

   - Add a mechanism to prevent tables from being unmapped prematurely
     due to reference counter overflows (Lv Zheng)"

* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
  Revert "ACPICA: Disassembler: Enhance resource descriptor detection"

Pull power management fixes from Rafael Wysocki:
 "These revert a recent cpufreq schedutil governor change that turned
  out to be problematic and fix a few minor issues in cpufreq, cpuidle
  and the Exynos devfreq drivers.

  Specifics:

   - Revert a recent cpufreq schedutil governor change that caused some
     systems to behave undesirably (Rafael Wysocki).

   - Fix a cpufreq conservative governor issue introduced during the
     3.10 cycle that prevents it from working as expected in some
     situations (Tomasz Wilczyński).

   - Fix an error code path in the generic cpuidle driver for DT-based
     systems (Christophe Jaillet).

   - Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
     Krzysztof Kozlowski)"

* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: dt: Add missing 'of_node_put()'
  cpufreq: conservative: Allow down_threshold to take values from 1 to 10
  Revert "cpufreq: schedutil: Reduce frequencies slower"
  PM / devfreq: exynos-ppmu: Staticize event list
  PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
  PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable

Merge branch 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid

Pull HID fix from Jiri Kosina:

 - ifdef-based bandaid for a long-standing issue with HID driver
   matching, avoiding regressions in cases where specific driver is not
   enabled in kernel .config, from Jiri Kosina

* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: let generic driver yield control iff specific driver has been enabled

Pull media fixes from Mauro Carvalho Chehab:

 - some build dependency issues at CEC core with randconfigs

 - fix an off by one error at vb2

 - a race fix at cec core

 - driver fixes at tc358743, sir_ir and rainshadow-cec

* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
  [media] cec: race fix: don't return -ENONET in cec_receive()
  [media] sir_ir: infinite loop in interrupt handler
  [media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
  [media] cec: improve MEDIA_CEC_RC dependencies
  [media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
  [media] rainshadow-cec: Fix missing spin_lock_init()
  [media] tc358743: fix register i2c_rd/wr function fix

The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
  i40e_vsi_remove_pvid
    i40e_vlan_stripping_disable
      i40e_aq_update_vsi_params
        i40e_asq_send_command
          mutex_lock --> may sleep

To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* acpica-fixes:
  ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
  Revert "ACPICA: Disassembler: Enhance resource descriptor detection"

* pm-cpufreq:
  cpufreq: conservative: Allow down_threshold to take values from 1 to 10
  Revert "cpufreq: schedutil: Reduce frequencies slower"

* pm-cpuidle:
  cpuidle: dt: Add missing 'of_node_put()'

* pm-devfreq:
  PM / devfreq: exynos-ppmu: Staticize event list
  PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
  PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable

Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited.  This was broken by
commit c0303efe ("net: reduce cycles spend on ICMP replies that
gets rate limited").

An ICMP response will usually be routed back-out the same incoming
interface.  Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback.  In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow().  Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").

This seems to fix the reproducer given by Florian.  While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).

Fixes: c0303efe ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I'm reviewing static checker warnings where we do ERR_PTR(0), which is
the same as NULL.  I'm pretty sure we intended to return ERR_PTR(-EINVAL)
here.  Sometimes these bugs lead to a NULL dereference but I don't
immediately see that problem here.

Fixes: 71d0ed70 ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update ->ndo_change_mtu() callback comment to remove text
about returning error in case of undefined callback. This
change makes the comment match the existing code behavior.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Laura reported a sleep-in-atomic kernel warning inside
tcf_act_police_init() which calls gen_replace_estimator() with
spinlock protection.

It is not necessary in this case, we already have RTNL lock here
so it is enough to protect concurrent writers. For the reader,
i.e. tcf_act_police(), it needs to make decision based on this
rate estimator, in the worst case we drop more/less packets than
necessary while changing the rate in parallel, it is still acceptable.
Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Nick Huber <nicholashuber@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).

To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.

This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To make it clear that we never use struct ifreq, cast from it
directly in the wext entrypoint and use struct iwreq from there
on. The next patch will remove the cast again and pass the
correct struct from the beginning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are no longer any drivers (in the tree proper, I didn't
check all the staging drivers) that take WEXT ioctls through
this API, the only remaining ones that even have ndo_do_ioctl
are using it only for private ioctls.

Therefore, we can remove this call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in the connect()
handler of the AF_CAIF socket. Since the syscall doesn't enforce a minimum
size of the corresponding memory region, very short sockaddrs (zero or one
byte long) result in operating on uninitialized memory while referencing
sa_family.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are two batman-adv bugfixes:

 - fix rx packet counters for local ARP replies, by Sven Eckelmann

 - fix memory leaks for unicast packetes received from another gateway
   in bridge loop avoidance, by Andreas Pape
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Some fixes:
 * Avi fixes some fallout from my mac80211 RX flags changes
 * Emmanuel fixes an issue with adhering to the spec, and
   an oversight in the SMPS management code
 * Jason's patch makes mac80211 use constant-time memory
   comparisons for message authentication, to avoid having
   potentially observable timing differences
 * my fix makes mac80211 set the basic rates bitmap before
   the channel so the next update to the driver has more
   consistent data - this required another rework patch to
   remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when dumping a context data only word number '1' is read for the
entire context.

Fixes: c965db44 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 90eff909 ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:

 drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
   drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
   mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
   mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's already added by pr_fmt so remove the explicit use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>