Conflicts:
	arch/arm/mach-tegra/board-harmony-pcie.c

To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* imx/board: (4 commits)
  Enable 32 bit flash support for iMX21ADS board
  ARM: mx31pdk: Add MC13783 RTC support
  iomux-mx25: configuration to support CSPI3 on CSI pins
  MX1:apf9328: Add i2c support

Updated to v3.2-rc6, conflicts:
	arch/arm/kernel/setup.c

The kernel configuration for the i.MX21ADS board (imx_v4_v5_defconfig)
doesn't enable 32 bit flash support. But the i.MX21ADS specific code
adds a 32 bit flash device, resulting in a kernel that refuses to
boot.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MX31PDK board has a MC13783 PMIC, which provides RTC functionality.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds necessary defines for the CSPI3 module (activated with
imx25_add_spi_imx2()) to work on the CSI pins (alternative mode 7).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* pxa/board:
  mioa701: add newly available DoC G3 chip

As the mioa701 board has a M-Systems DiskOnChip G3 chip, add
it to the platform resources of the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@atosorigin.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

* tegra/boards:
  arm/tegra: remove __initdata annotation from pinmux tables
  arm/tegra: Use bus notifiers to trigger pinmux setup
  arm/tegra: Refactor board-*-pinmux.c to share code
  arm/tegra: Fix mistake in Trimslice's pinmux
  arm/tegra: Rework Seaboard-vs-Ventana pinmux table
  arm/tegra: Remove useless entries from ventana_pinmux[]
  arm/tegra: PCIe: Remove include of mach/pinmux.h
  arm/tegra: Harmony PCIe: Don't touch pinmux
  arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
  arm/tegra: Split Seaboard GPIO table to allow for Ventana
  ARM: tegra: paz00: Fix board pinmux table.
  ARM: tegra: paz00: add support for wakeup gpio key

Merge branch 'for-3.3/boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/boards

Merge branch 'for-3.3/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/soc

Instead of reshuffling what functions in the pinmux paths should be
__init and thus could keep references to __initdata, let's just remove
the annotations for now -- the tables are moving to device tree in the
next version anyway and the whole subsystem is being wired up. We will
go back and re-annotate where appropriate once things settle down.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>

This fixes a build break attempting to build a Tegra20-only kernel
without device tree enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Now that Tegra20 and Tegra30 device tree board files are separate,
MACH_TEGRA_DT (which enables the Tegra20 device tree board file) should
depend on Tegra20 support being enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

tegra_init_clock() is written to call tegra2_init_clocks(), which only
exists if Tegra20 support is enabled. This breaks the build of a
Tegra30-only kernel.

tegra_init_clock() isn't actually used any more; tegra20_init_early()
calls tegra2_init_clocks() directly. So, just delete this function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

tegra30_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

tegra20_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Currently, the Tegra pinmux is initialized at different times when booting
with and without device tree:

Without device tree:

1) Pinmux and GPIO drivers are registered.
2) Pinmux is configured.
3) All other drivers are registered.

With device tree:

1) All drivers are registered and probed, including pinmux and GPIO.
2) Pinmux is configured.

This change modifies board-pinmux.c to detect pinmux and GPIO driver
registration using bus notifiers. This allows pinmux configuration to
happen immediately after the pinmux driver is probed, irrespective of
whether the pinmux driver is manually registered by board-pinmux.c, or
if it's instantiated during device tree parsing.

To support this with device tree, the pinmux init functions must be
called prior to instantiating devices from device tree, so that the
notifiers are set up before-hand.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This moves the implementation of *_pinmux_init() into a single location.
The board-specific pinmux data is left in each board's own file. This
will allow future changes that set up the pinmux in a more complex
fashion to do so without duplicating that code in each board's pinmux
file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pin group PTA does not support function RSVD3. However, the current
pinmux driver doesn't check this when setting RSVD functions, and ends
up writing 3 to the HW register. 3 is actually represented by function
GMI, so update the pinmux table to request that instead in order to
obtain the same register programming without requesting invalid
configurations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Rather than modifying seaboard_pinmux[] using ventana_pinmux[], split
seaboard_pinmux[] into common_pinmux[] and seaboard_pinmux[], and then
actually apply common_pinmux[] always, followed by the appopriate one
of seaboard_pinmux[] or ventana_pinmux[].
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Some of the entries in ventana_pinmux[] are identical to what's already in
seaboard_pinmux[]. Remove the overrides from the Ventana table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Nothing in this file needs this header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Harmony pinmux table is already set up to mux the PCIe signals onto
the appropriate pin groups. Don't manually fiddle with the pinmux in the
Harmony PCIe setup code.

Merge note: This will have a merge conflict with Peter De Schrijver's
"arm/tegra: prepare pinmux code for multiple tegra variants" due to
context. When merging the two, make sure to also remove the include
of <mach/pinmux-tegra20.h> that his patch added, since it's no longer
needed after this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The pinctrl device name is included in the pinctrl map table, and used
as a parameter to pin_config_*() functions. Hence, it must be the same
for non-DT and DT kernels. Add AUXDATA to cause this.

The GPIO device name will be used by the pinmux/GPIO initialization code
in a later patch, and needs to stay constant.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Seaboard and Ventana share some GPIOs, but others are different. Split the
GPIO table into common, seaboard-specific, and ventana-specific tables, so
that only the correct ones are enabled for each board. Add a few missing
audio-related GPIOs for Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Update the defconfig for tegra due to the addition of tegra30 and rename
of t20/t30 options.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>

Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add support for tegra30 SoC. This includes a device tree compatible type for
this SoC ("nvidia,tegra30") and adds L2 cache initialization for this new SoC.
The clock framework is still missing, which prevents most drivers from working.
The basic IRQs are the same, so remove the dependency on
CONFIG_ARCH_TEGRA_2x_SOC.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Define the pinmuxing and pindrive tables for tegra30. The pinmux table defines
the available functions for each pinmux group. The pindrive table defines the
default pullup or pulldowns for each group.

Derived from code by Scott Williams (scwilliams@nvidia.com)
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add new fields to struct tegra_pingroup_desc to support new hardware features
introduced in the tegra30 SoC. The pinmux driver won't use those fields yet,
but the tegra30 pinmux tables will already provide the necessary data.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch modifies the pinmux code to be useable for multiple tegra variants.
Some tegra20 specific constants will be replaced by variables which will be
initialized to the appropriate value at runtime.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Rename pinmux-t2.h and pinmux-t2-tables.c to the new tegra naming. This file
will be reworked somewhat in the next patch to support multiple tegra SoC
types.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Generalize L2 cache initialization and discover L2 cache associativity at
runtime.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Use PMC reset rather then CAR system reset as recommended by the hardware
team.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Tegra20 based boards will be handled by the current board-dt.c file. Tegra30
based boards will be handled by a new board-dt-tegra30.c file. Hence rename
the existing board-dt.c to board-dt-tegra20.c to reflect its use.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch splits the early init code in a common and a tegra20 specific part.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

don't export clk_measure_input_freq as its functionality is also available
using clk_get_rate().
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Rework the tegra20 clock code to support multiple tegra variants :

 * remove tegra2_periph_reset_assert/tegra2_periph_reset_deassert. This
   functionality should be in clock.c.

 * remove tegra_sdmmc_tap_delay and export tegra2_sdmmc_tap_delay
   directly. This feature is handled inside the sdmmc block from tegra30
   onwards. So there is no need for support in the clock code beyond
   tegra20. There are no in tree users of this function.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>