The patch disables the regulator in case of errors, if we have it.
In addition, the patch adds support for deferred regulator probe and
makes error path are a bit clean.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pdev->id is not a valid choice for device-tree probed devices. So use
the (properly determined) line from efm32_uart_probe consistenly
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Storing one struct per known board would be overkill. Pre-cast the
driver_data pointer to an unsigned long to avoid the pointer to int
compiler warning:

drivers/tty/serial/pch_uart.c:431:10: warning: cast from pointer to
integer of different size [-Wpointer-to-int-cast]

Unify the signed-ness of the baud and uartclk types throughout the
driver.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Because the UART lack of receive timeout register, so we use a timer to trigger
data receive.
The DBGU is regarded as UART.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Distinguish usart and uart by read ip name register,
The usart read name is "USAR",
The uart and dbgu read name is "DBGU".
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We will switch to pio mode when request of dma or pdc fail.
But soon or later, when the request is success, the transfer mode can switch to them at
next open serial port action.
So in startup stage, we should get original transfer mode.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Request a cyclic dma channel for rx dma use. Use cyclic transfer is to prevent
receive data overrun.

We allocate a cycle dma cookie after request channel,
after that, enable uart timeout interrupt in startup stage, when data successful
received, the timeout callback will check the residual bytes and insert
receiving datas into the framework during the transfer interval.

When current descriptor finished, the dma callback will also check the residual
bytes and filp the receiving data.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Request a slave dma channel for tx dma use. Tx dma will setup a single transfer,
when transfer complete, it will call atmel_complete_tx_dma to do finish stuff.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

use function pointer can avoid define atmel_use_pdc_tx/rx everywhere.
(*prepare_rx/tx)() is in setup transfer stage.
(*schedule_rx/tx)() is in tasklet schedule stage.
(*release_rx/tx)() is used when shutdown the transfer.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA is available since at91sam9x5 socs, before that, we use PDC.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dmi_table is best accessed from the probe function, which is not
an __init function. Drop the __initdata annotation from the dmi_table
to avoid the section mismatch compiler warnings:

WARNING: drivers/tty/serial/pch_uart.o(.text+0x4871): Section mismatch
in reference from the function pch_uart_init_port() to the variable
.init.data:pch_uart_dmi_table
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Found with coccinelle, manually fixed and verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes wrong dev_pm_ops which caused by commit:
serial: max310x: Driver rework.

  CC      drivers/tty/serial/max310x.o
  LD      drivers/video/fb.o
  CC      drivers/w1/slaves/w1_ds2433.o
  CC      drivers/w1/slaves/w1_ds2760.o
  CC      drivers/xen/balloon.o
  CC      drivers/video/backlight/adp8870_bl.o
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 - Driver fixes for AM33xx, SIRF and PFC pin controllers
 - Fix a compile warning from the pinctrl single-register driver
 - Fix a little nasty memory leak

* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix a memleak when freeing maps
  pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
  pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
  arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
  pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
  pinctrl: sirf: fix the pin number and mux bit for usp0
  pinctrl: am33xx dt binding: correct include path

Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Oleg is working on fixing a very tight race between opening a event
  file and deleting that event at the same time (both must be done as
  root).

  I also found a bug while testing Oleg's patches which has to do with a
  race with kprobes using the function tracer.

  There's also a deadlock fix that was introduced with the previous
  fixes"

* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
  ftrace: Add check for NULL regs if ops has SAVE_REGS set
  tracing: Kill trace_cpu struct/members
  tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
  tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
  tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
  tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
  tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
  tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()

Pull SCSI fixes from James Bottomley:
 "This is five bug fixes, two of which fix long standing problems
  causing crashes (sd and mvsas).  The remaining three are hung (isci
  race) or lost (qla2xxx, isci) devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] isci: fix breakage caused by >16byte CDB patch
  [SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
  [SCSI] sd: fix crash when UA received on DIF enabled device
  [SCSI] qla2xxx: Properly set the tagging for commands.
  [SCSI] isci: Fix a race condition in the SSP task management path

Replace kzalloc and clk_get by their managed counterparts to simplify
error and cleanup paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

-> The ledptrs[] array is never initialized.
-> There is no place where kbd->ledmode is set to LED_SHOW_MEM therefore the if
   statement does not make much sense.
-> Since LED_SHOW_MEM is not used, it can be removed from the header file as well.
Signed-off-by: Andreas Platschek <andi.platschek@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTDM cores have a TX fifo that can accept more than one
character per register write, but the msm_serial driver currently
only supports 1 character mode. Add support for this mode of operation
to speed up the transmit path on DM devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently msm_set_baud_rate() assumes the uart clock rate is
1.8432 MHz. This is not always true, and limits our options to
program the baud rate. Instead of assuming the rate and
hard-coding the baud_code based on it, calculate the divider that
we want and try to find the closest baud_code that matches. This
allows us to support uarts with faster clock speeds.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/msm_serial.c:302:6: warning: symbol 'msm_set_mctrl' was
not declared. Should it be static?
drivers/tty/serial/msm_serial.c:597:17: warning: incorrect type in argument 2
(different address spaces)
drivers/tty/serial/msm_serial.c:597:17: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:597:17: got unsigned int *
drivers/tty/serial/msm_serial.c:608:33: warning: incorrect type in argument 1
(different address spaces)
drivers/tty/serial/msm_serial.c:608:33: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:608:33: got unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: warning: incorrect type in assignment
(different address spaces)
drivers/tty/serial/msm_serial.c:648:37: expected unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: got void [noderef] <asn:2>*

Mark the ioremapped memory as __iomem and use writel instead of
iowrite because we're not dealing with PCI devices. Also, mark
msm_set_mctrl() static because it isn't used outside this file.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTDM serial devices require us to wait for the entire TX fifo
to drain before we can change the contents of the NCF_TX
register. Furthermore, if we write any characters to the TX fifo
within the same clock cycle of changing the NCF_TX register the
NCF_TX register won't latch properly.

To fix these issues we should read back the NCF_TX register to
delay any TX fifo accesses by a clock cycle and we should wait
for the TX fifo to drain (instead of just waiting for the fifo to
be ready to receive more characters). Failure to do so leads to
random NUL bytes interspersed in the output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These two defines are no longer used.  They were only used by the PCI
serial driver "8250_pci" to support the original ADDI-DATA APCI-7800
card.  In that driver, PCI_VENDOR_ID_ADDIDATA_OLD has been replaced with
PCI_VENDOR_ID_AMCC which has the same value (0x10e8), and
PCI_DEVICE_ID_ADDIDATA_APCI7800 has been replaced with a local #define
PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 with the same value (0x818e).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC).  Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>.  The vender ID is actually
assigned to Applied Micro Circuits Corporation.  The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card.  Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI_VENDOR_ID_AMCC is defined locally in
"drivers/staging/comedi/comedidev.h" for a few comedi hardware drivers,
namely "adl_pci9118", "addi_apci_1500" and "addi_apci_3120" (also
"addi_apci_1710" but that is not currently built and will probably be
removed soon).  Move the define into "include/linux/pci_ids.h" as it is
shared by several drivers (albeit all comedi drivers currently).

PCI_VENDOR_ID_AMCC happens to have the same value (0x10e8) as
PCI_VENDOR_ID_ADDIDATA_OLD.  The vendor ID is actually assigned to
Applied Micro Circuits Corporation and Addi-Data were using device IDs
assigned by AMCC on some of their earlier PCI boards. The
PCI_VENDOR_ID_ADDIDATA_OLD define is still being used by the "8250_pci"
PCI serial board driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP is common
across all the ST parts for settop box platforms.

ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
It support all industry standard baud rates.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver fails to build on x86 because writel_relaxed isn't available
there. That function exists on arm, arm64, avr32, hexagon, mips and sh,
but adding all these is overkill so stick to arm only.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing iounmap() before return from msm_request_port()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No idea why we have redundant testing for ifdef CONFIG_SERIAL_BFIN_MODULE,
check it once is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the DMI interface rather than manually matching DMI strings.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Michael Brunner <mibru@gmx.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some serial ports will not use the standard base baud rate. Report
this after initialization so it might be discovered and used for early
console configuration.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If earlyprintk is enabled and current UART is console port the platform
code can mark it as RPM_ACTIVE to sync real IP state with PM Runtime and
avoid resuming of already active device, but now, driver initialization
will be performed in the wrong way:

	pm_runtime_enable(&pdev->dev);
    <-- PM runtime alowed (device state RPM_ACTIVE)
	if (omap_up_info->autosuspend_timeout == 0)
		omap_up_info->autosuspend_timeout = -1;
	device_init_wakeup(up->dev, true);
	pm_runtime_use_autosuspend(&pdev->dev);
	<-- update_autosuspend() will be called and it will disable device
        (device state RPM_SUSPENDED)
	pm_runtime_set_autosuspend_delay(&pdev->dev,
			omap_up_info->autosuspend_timeout);
	<-- update_autosuspend() will be called which will re-enable device
        (device state RPM_ACTIVE), because autosuspend_timeout < 0

	pm_runtime_irq_safe(&pdev->dev);
	pm_runtime_get_sync(&pdev->dev);
	<-- will do nothing

Such behavior isn't expected by OMAP serial drivers and causes
unpredictable calls of serial_omap_runtime_suspend() and
serial_omap_runtime_resume().

Hence, fix it by allowing PM runtime only after all its parameters are
configured.

CC: Tony Lindgren <tony@atomide.com>
CC: Rajendra Nayak <rnayak@ti.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>