With a public notification, NIST now allows the use of RSA keys with a
modulus >= 2048 bits. The new rule allows any modulus size >= 2048 bits
provided that either 2048 or 3072 bits are supported at least so that
the entire RSA implementation can be CAVS tested.

This patch fixes the inability to boot the kernel in FIPS mode, because
certs/x509.genkey defines a 4096 bit RSA key per default. This key causes
the RSA signature verification to fail in FIPS mode without the patch
below.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

clk_prepare_enable() may fail, so we should better check its return
value and propagate it in the case of failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove omap3_rom_rng_data_present method as it was returning 1 always.
Use .read callback instead of .data_read callback. This avoids use of
obsolete callbacks.

This patch is not tested with hardware as I don't have access to it.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fix to return a negative error code from the error handling
case instead of 0.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add the missing unlock before return from function sun4i_hash()
in the error handling case.

Fixes: 477d9b2e ("crypto: sun4i-ss - unify update/final function")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

If the architecture selected the xor function with XOR_SELECT_TEMPLATE
the speed result of the do_xor_speed benchmark is of limited value.
The speed measurement increases the bootup time a little, which can
makes a difference for kernels used in container like virtual machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently, very few RNG drivers support single byte reads using the
->read() interface. Of the 14 drivers in drivers/char/hw_random that
support this interface only three of these actually support max == 1.
The other behaviours vary between return 0, return 2, return 4 and return
-EIO).

This is not a problem in practice because the core hw_random code never
performs a read shorter than 16 bytes. The documentation for this function
already contrains the alignment of the buffer pointer, so let's also
guarantee that the buffer is at least as large as its alignment.

This constraint is intended to be the weakest guarantee neccessary to
allow driver writers to safely simplify their code.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Update the documentation for crypto_register_algs() and
crypto_unregister_algs() to match the actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When calling the DRBG health test in FIPS mode, the Jitter RNG is not
yet present in the kernel crypto API which will cause the instantiation
to fail and thus the health test to fail.

As the health tests cover the enforcement of various thresholds, invoke
the functions that are supposed to enforce the thresholds directly.

This patch also saves precious seed.
Reported-by: Tapas Sarangi <TSarangi@trustwave.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The field "owner" is set by the core.
Thus delete an unneeded initialisation.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Fixes the following sparse warning:

drivers/crypto/ccp/ccp-dev.c:62:14: warning:
 symbol 'ccp_increment_unit_ordinal' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Two crypto alg are badly indented, this patch fix this style issue.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The dev *ss is stored both in sun4i_tfm_ctx and sun4i_req_ctx.
Since this pointer will never be changed during tfm life, it is better
to remove it from sun4i_req_ctx.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Two words are badly spelled, this patch respell them.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The ss variable is never used, remove it.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The update and final functions have lots of common action.
This patch mix them in one function.
This will give some improvements:
- This will permit asynchronous support more easily
- This will permit to use finup/digest functions with some performance
  improvements
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The variable i is always checked against unsigned value and cannot be
negative.
This patch set it as unsigned.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The sentence 'Based on' is misspelled, respell it.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Don't use 64 'as is', as max block size in mv_cesa_ahash_cache_req. Use
CESA_MAX_HASH_BLOCK_SIZE instead, this is better for readability.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently, in mv_cesa_{md5,sha1,sha256}_init creq->state is initialized
before the call to mv_cesa_ahash_init. This is wrong because this
function fills creq with zero by using memset, so its 'state' that
contains the default DIGEST is overwritten. This commit fixes the issue
by initializing creq->state just after the call to mv_cesa_ahash_init.

Fixes: commit b0ef5106 ("crypto: marvell/cesa - initialize hash...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

So far, sub part of mv_cesa_int was responsible of dequeuing complete
requests, then call the 'cleanup' operation on these reqs and call the
crypto api callback 'complete'. The problem is that the transformation
context 'ctx' is retrieved only once before the while loop. Which means
that the wrong 'cleanup' operation might be called on the wrong type of
cesa requests, it can lead to memory corruptions with this message:

marvell-cesa f1090000.crypto: dma_pool_free cesa_padding, 5a5a5a5a/5a5a5a5a (bad dma)

This commit fixes the issue, by updating the transformation context for
each dequeued cesa request.

Fixes: commit 85030c51 ("crypto: marvell - Add support for chai...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The mv_cesa_ahash_cache_req() function always returns 0, which makes
its return value pretty much useless. However, in addition to
returning a useless value, it also returns a boolean in a variable
passed by reference to indicate if the request was already cached.

So, this commit changes mv_cesa_ahash_cache_req() to return this
boolean. It consequently simplifies the only call site of
mv_cesa_ahash_cache_req(), where the "ret" variable is no longer
needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The mv_cesa_ahash_init() function always returns 0, and the return
value is anyway never checked. Turn it into a function returning void.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The dma_iter parameter of mv_cesa_ahash_dma_add_cache() is never used,
so get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The mv_cesa_dma_add_op() function builds a mv_cesa_tdma_desc structure
to copy the operation description to the SRAM, but doesn't explicitly
initialize the destination of the copy. It works fine because the
operatin description must be copied at the beginning of the SRAM, and
the mv_cesa_tdma_desc structure is initialized to zero when
allocated. However, it is somewhat confusing to not have a destination
defined.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

While debugging setkey issues, the following warnings were found while
trying to reinsert the caam module.  Fix this by avoiding the duplicated
cleanup in the probe path after caam_remove(), which has already cleaned
up the resources.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 2346 at /home/rmk/git/linux-rmk/mm/vmalloc.c:1490 __vunmap+0xcc/0xf4
Trying to vfree() nonexistent vm area (f2400000)
Modules linked in: caam(+) cbc rfcomm bnep bluetooth nfsd em28xx_rc si2157 si2168 em28xx_dvb uvcvideo snd_soc_imx_sgtl5000 em28xx snd_soc_imx_spdif tveeprom snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_sgtl5000 imx_sdma imx2_wdt coda v4l2_mem2mem videobuf2_dma_contig snd_soc_fsl_ssi rc_cec snd_soc_fsl_spdif imx_pcm_dma videobuf2_vmalloc videobuf2_memops imx_thermal dw_hdmi_ahb_audio dw_hdmi_cec etnaviv fuse rc_pinnacle_pctv_hd [last unloaded: caam]
CPU: 0 PID: 2346 Comm: modprobe Tainted: G        W       4.8.0-rc1+ #2014
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013bb0>] (dump_backtrace) from [<c0013d4c>] (show_stack+0x18/0x1c)
[<c0013d34>] (show_stack) from [<c0357c00>] (dump_stack+0xa4/0xdc)
[<c0357b5c>] (dump_stack) from [<c002e650>] (__warn+0xdc/0x108)
[<c002e574>] (__warn) from [<c002e734>] (warn_slowpath_fmt+0x40/0x48)
[<c002e6f8>] (warn_slowpath_fmt) from [<c0151708>] (__vunmap+0xcc/0xf4)
[<c015163c>] (__vunmap) from [<c015177c>] (vunmap+0x4c/0x54)
[<c0151730>] (vunmap) from [<c001f48c>] (__iounmap+0x2c/0x30)
[<c001f460>] (__iounmap) from [<c001f118>] (iounmap+0x1c/0x20)
[<c001f0fc>] (iounmap) from [<bf247ae4>] (caam_probe+0x3dc/0x1498 [caam])
[<bf247708>] (caam_probe [caam]) from [<c042da8c>] (platform_drv_probe+0x58/0xb8)
[<c042da34>] (platform_drv_probe) from [<c042bb4c>] (driver_probe_device+0x1fc/0x2b8)
[<c042b950>] (driver_probe_device) from [<c042bcc4>] (__driver_attach+0xbc/0xc0) r10:00000000 r8:bf24b000 r7:00000000 r6:ef215844 r5:bf2490c4 r4:ef215810
[<c042bc08>] (__driver_attach) from [<c0429f14>] (bus_for_each_dev+0x5c/0x90)
[<c0429eb8>] (bus_for_each_dev) from [<c042b358>] (driver_attach+0x24/0x28)
[<c042b334>] (driver_attach) from [<c042b058>] (bus_add_driver+0xf4/0x200)
[<c042af64>] (bus_add_driver) from [<c042cadc>] (driver_register+0x80/0xfc)
[<c042ca5c>] (driver_register) from [<c042d960>] (__platform_driver_register+0x48/0x4c)
[<c042d918>] (__platform_driver_register) from [<bf24b018>] (caam_driver_init+0x18/0x24 [caam])
[<bf24b000>] (caam_driver_init [caam]) from [<c00098ac>] (do_one_initcall+0x44/0x178)
[<c0009868>] (do_one_initcall) from [<c010e034>] (do_init_module+0x68/0x1d8)
[<c010dfcc>] (do_init_module) from [<c00c8fbc>] (load_module+0x1974/0x20b0)
[<c00c7648>] (load_module) from [<c00c98d0>] (SyS_finit_module+0x94/0xa0)
[<c00c983c>] (SyS_finit_module) from [<c000fda0>] (ret_fast_syscall+0x0/0x1c)
---[ end trace 34e3370d88bb1786 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2346 at /home/rmk/git/linux-rmk/drivers/clk/clk.c:594 clk_core_disable+0xe4/0x26c
Modules linked in: caam(+) cbc rfcomm bnep bluetooth nfsd em28xx_rc si2157 si2168 em28xx_dvb uvcvideo snd_soc_imx_sgtl5000 em28xx snd_soc_imx_spdif tveeprom snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_sgtl5000 imx_sdma imx2_wdt coda v4l2_mem2mem videobuf2_dma_contig snd_soc_fsl_ssi rc_cec snd_soc_fsl_spdif imx_pcm_dma videobuf2_vmalloc videobuf2_memops imx_thermal dw_hdmi_ahb_audio dw_hdmi_cec etnaviv fuse rc_pinnacle_pctv_hd [last unloaded: caam]
CPU: 0 PID: 2346 Comm: modprobe Tainted: G        W       4.8.0-rc1+ #2014
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013bb0>] (dump_backtrace) from [<c0013d4c>] (show_stack+0x18/0x1c)
[<c0013d34>] (show_stack) from [<c0357c00>] (dump_stack+0xa4/0xdc)
[<c0357b5c>] (dump_stack) from [<c002e650>] (__warn+0xdc/0x108)
[<c002e574>] (__warn) from [<c002e6a4>] (warn_slowpath_null+0x28/0x30)
[<c002e67c>] (warn_slowpath_null) from [<c05b113c>] (clk_core_disable+0xe4/0x26c)
[<c05b1058>] (clk_core_disable) from [<c05b2e3c>] (clk_core_disable_lock+0x20/0x2c)
[<c05b2e1c>] (clk_core_disable_lock) from [<c05b2e6c>] (clk_disable+0x24/0x28)
[<c05b2e48>] (clk_disable) from [<bf247b04>] (caam_probe+0x3fc/0x1498 [caam])
[<bf247708>] (caam_probe [caam]) from [<c042da8c>] (platform_drv_probe+0x58/0xb8)
[<c042da34>] (platform_drv_probe) from [<c042bb4c>] (driver_probe_device+0x1fc/0x2b8)
[<c042b950>] (driver_probe_device) from [<c042bcc4>] (__driver_attach+0xbc/0xc0) r10:00000000 r8:bf24b000 r7:00000000 r6:ef215844 r5:bf2490c4 r4:ef215810
[<c042bc08>] (__driver_attach) from [<c0429f14>] (bus_for_each_dev+0x5c/0x90)
[<c0429eb8>] (bus_for_each_dev) from [<c042b358>] (driver_attach+0x24/0x28)
[<c042b334>] (driver_attach) from [<c042b058>] (bus_add_driver+0xf4/0x200)
[<c042af64>] (bus_add_driver) from [<c042cadc>] (driver_register+0x80/0xfc)
[<c042ca5c>] (driver_register) from [<c042d960>] (__platform_driver_register+0x48/0x4c)
[<c042d918>] (__platform_driver_register) from [<bf24b018>] (caam_driver_init+0x18/0x24 [caam])
[<bf24b000>] (caam_driver_init [caam]) from [<c00098ac>] (do_one_initcall+0x44/0x178)
[<c0009868>] (do_one_initcall) from [<c010e034>] (do_init_module+0x68/0x1d8)
[<c010dfcc>] (do_init_module) from [<c00c8fbc>] (load_module+0x1974/0x20b0)
[<c00c7648>] (load_module) from [<c00c98d0>] (SyS_finit_module+0x94/0xa0)
[<c00c983c>] (SyS_finit_module) from [<c000fda0>] (ret_fast_syscall+0x0/0x1c)
---[ end trace 34e3370d88bb1787 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2346 at /home/rmk/git/linux-rmk/drivers/clk/clk.c:476 clk_core_unprepare+0x204/0x388
Modules linked in: caam(+) cbc rfcomm bnep bluetooth nfsd em28xx_rc si2157 si2168 em28xx_dvb uvcvideo snd_soc_imx_sgtl5000 em28xx snd_soc_imx_spdif tveeprom snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_sgtl5000 imx_sdma imx2_wdt coda v4l2_mem2mem videobuf2_dma_contig snd_soc_fsl_ssi rc_cec snd_soc_fsl_spdif imx_pcm_dma videobuf2_vmalloc videobuf2_memops imx_thermal dw_hdmi_ahb_audio dw_hdmi_cec etnaviv fuse rc_pinnacle_pctv_hd [last unloaded: caam]
CPU: 0 PID: 2346 Comm: modprobe Tainted: G        W       4.8.0-rc1+ #2014
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013bb0>] (dump_backtrace) from [<c0013d4c>] (show_stack+0x18/0x1c)
[<c0013d34>] (show_stack) from [<c0357c00>] (dump_stack+0xa4/0xdc)
[<c0357b5c>] (dump_stack) from [<c002e650>] (__warn+0xdc/0x108)
[<c002e574>] (__warn) from [<c002e6a4>] (warn_slowpath_null+0x28/0x30)
[<c002e67c>] (warn_slowpath_null) from [<c05b0834>] (clk_core_unprepare+0x204/0x388)
[<c05b0630>] (clk_core_unprepare) from [<c05b4c0c>] (clk_unprepare+0x2c/0x34)
[<c05b4be0>] (clk_unprepare) from [<bf247b0c>] (caam_probe+0x404/0x1498 [caam])
[<bf247708>] (caam_probe [caam]) from [<c042da8c>] (platform_drv_probe+0x58/0xb8)
[<c042da34>] (platform_drv_probe) from [<c042bb4c>] (driver_probe_device+0x1fc/0x2b8)
[<c042b950>] (driver_probe_device) from [<c042bcc4>] (__driver_attach+0xbc/0xc0) r10:00000000 r8:bf24b000 r7:00000000 r6:ef215844 r5:bf2490c4 r4:ef215810
[<c042bc08>] (__driver_attach) from [<c0429f14>] (bus_for_each_dev+0x5c/0x90)
[<c0429eb8>] (bus_for_each_dev) from [<c042b358>] (driver_attach+0x24/0x28)
[<c042b334>] (driver_attach) from [<c042b058>] (bus_add_driver+0xf4/0x200)
[<c042af64>] (bus_add_driver) from [<c042cadc>] (driver_register+0x80/0xfc)
[<c042ca5c>] (driver_register) from [<c042d960>] (__platform_driver_register+0x48/0x4c)
[<c042d918>] (__platform_driver_register) from [<bf24b018>] (caam_driver_init+0x18/0x24 [caam])
[<bf24b000>] (caam_driver_init [caam]) from [<c00098ac>] (do_one_initcall+0x44/0x178)
[<c0009868>] (do_one_initcall) from [<c010e034>] (do_init_module+0x68/0x1d8)
[<c010dfcc>] (do_init_module) from [<c00c8fbc>] (load_module+0x1974/0x20b0)
[<c00c7648>] (load_module) from [<c00c98d0>] (SyS_finit_module+0x94/0xa0)
[<c00c983c>] (SyS_finit_module) from [<c000fda0>] (ret_fast_syscall+0x0/0x1c)
---[ end trace 34e3370d88bb1788 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Threaded interrupts can perform the function of the tasklet, and much
more safely too - without races when trying to take the tasklet and
interrupt down on device removal.

With the old code, there is a window where we call tasklet_kill().  If
the interrupt handler happens to be running on a different CPU, and
subsequently calls tasklet_schedule(), the tasklet will be re-scheduled
for execution.

Switching to a hardirq/threadirq combination implementation avoids this,
and it also means generic code deals with the teardown sequencing of the
threaded and non-threaded parts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add a helper to map the source scatterlist into the descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add a helper function to perform the descriptor allocation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Strictly, dma_map_sg() may coalesce SG entries, but in practise on iMX
hardware, this will never happen.  However, dma_map_sg() can fail, and
we completely fail to check its return value.  So, fix this properly.

Arrange the code to map the scatterlist early, so we know how many
scatter table entries to allocate, and then fill them in.  This allows
us to keep relatively simple error cleanup paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Ensure that we clean up allocations and DMA mappings after encountering
an error rather than just giving up and leaking memory and resources.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Since the extended descriptor includes the hardware descriptor, and the
sec4 scatterlist immediately follows this, we can declare it as a array
at the very end of the extended descriptor.  This allows us to get rid
of an initialiser for every site where we allocate an extended
descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Mark the hardware descriptor as being cache line aligned; on DMA
incoherent architectures, the hardware descriptor should sit in a
separate cache line from the CPU accessed data to avoid polluting
the caches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Rather than giving the descriptor as hw_desc[0], give it's real size.
All places where we allocate an ahash_edesc incorporate DESC_JOB_IO_LEN
bytes of job descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

caamhash contains this weird code:

	src_nents = sg_count(req->src, req->nbytes);
	dma_map_sg(jrdev, req->src, src_nents ? : 1, DMA_TO_DEVICE);
	...
	edesc->src_nents = src_nents;

sg_count() returns zero when sg_nents_for_len() returns zero or one.
This means we don't need to use a hardware scatterlist.  However,
setting src_nents to zero causes problems when we unmap:

	if (edesc->src_nents)
		dma_unmap_sg_chained(dev, req->src, edesc->src_nents,
				     DMA_TO_DEVICE, edesc->chained);

as zero here means that we have no entries to unmap.  This causes us
to leak DMA mappings, where we map one scatterlist entry and then
fail to unmap it.

This can be fixed in two ways: either by writing the number of entries
that were requested of dma_map_sg(), or by reworking the "no SG
required" case.

We adopt the re-work solution here - we replace sg_count() with
sg_nents_for_len(), so src_nents now contains the real number of
scatterlist entries, and we then change the test for using the
hardware scatterlist to src_nents > 1 rather than just non-zero.

This change passes my sshd, openssl tests hashing /bin and tcrypt
tests.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Properly allocate enough memory to respect the fallback.
Signed-off-by: Will Thomas <will.thomas@imgtec.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently the probe function only emits an output on success
when debug is specifically enabled. It would be more useful
if this happens by default.
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Will Thomas <will.thomas@imgtec.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Currently the img-hash accelerator does not probe
successfully due to a change in the checks made during
registration with the crypto framework. This is due to
import and export functions not being defined. Correct
this.
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Will Thomas <will.thomas@imgtec.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>