- 12 Oct, 2017 10 commits
-
-
Biju Das authored
This patch adds DMA properties to the HSUSB node. Signed-off-by:
Biju Das <biju.das@bp.renesas.com> Signed-off-by:
Chris Paterson <chris.paterson2@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
Enable HS-USB device for the iWave G20D-Q7 carrier board based on RZ/G1M. Also disable the host mode support on usb otg port by default to avoid pin conflicts. Signed-off-by:
-
Biju Das authored
Define the R8A7743 generic part of the HS-USB device node. It is up to the board file to enable the device. Signed-off-by:
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to them. Signed-off-by:
-
Biju Das authored
Describe the PCI USB devices that are behind the PCI bridges, adding necessary links to the USB PHY device. Signed-off-by:
-
Biju Das authored
Define the r8a7745 generic part of the USB PHY device node. Signed-off-by:
-
Biju Das authored
Add device nodes for the r8a7745 internal PCI bridge devices. Signed-off-by:
-
Dietmar Eggemann authored
The following 'capacity-dmips-mhz' dt property values are used: Cortex-A15: 1024, Cortex-A7: 539 They have been derived form the cpu_efficiency values: Cortex-A15: 3891, Cortex-A7: 2048 by scaling them so that the Cortex-A15s (big cores) use 1024. The cpu_efficiency values were originally derived from the "Big.LITTLE Processing with ARM Cortex
™ -A15 & Cortex-A7" white paper (http://www.cl.cam.ac.uk/~rdm34/big.LITTLE.pdf). Table 1 lists 1.9x (3891/2048) as the Cortex-A15 vs Cortex-A7 performance ratio for the Dhrystone benchmark. The following platform is affected once cpu-invariant accounting support is re-connected to the task scheduler: r8a7790-lager Signed-off-by:Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by:
-
- 09 Oct, 2017 2 commits
-
-
Fabrizio Castro authored
This patch adds a .dtsi that describes the camera daughter board and a .dts to describe the HW made of iWave's RZ/G1M SoM, iWave's RZ/G1M/G1N Qseven carrier board, and the camera daughter board. The camera daughter board .dtsi adds support for ttySC[14]. Signed-off-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by:
-
Fabrizio Castro authored
Since the same carrier board may host RZ/G1M and RZ/G1N based Systems on Module, the DT architecture for iwg20d-q7 needs better decoupling. This patch provides: * iwg20d-q7-common.dtsi - its purpose is to define the carrier board definitions, and its content is basically the same as the previous version of r8a7743-iwg20d-q7.dts, only it has no reference to the SoM .dtsi, and that's why the filename doesn't mention the SoC name any more. * r8a7743-iwg20d-q7.dts - its new purpose is to put together the SoM .dtsi (r8a7743-iwg20m.dtsi) and the carrier board .dtsi defined by this very patch, along with "model" and "compatible" properties. The final DT architecture to describe the board is now: r8a7743-iwg20d-q7.dts # Carrier Board + SoM ├── r8a7743-iwg20m.dtsi # SoM │ └── r8a7743.dtsi # SoC └── iwg20d-q7-common.dtsi # Carrier Board and maximizes the reuse of the definitions for the carrier board and for the SoM. Signed-off-by:
-
- 06 Oct, 2017 4 commits
-
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
Geert Uytterhoeven authored
Use the preferred generic node name instead of the specific name. Signed-off-by:
-
- 05 Oct, 2017 2 commits
-
-
Jacopo Mondi authored
MTU2 multi-function/multi-channel timer/counter is not enabled for GR-Peach board. The timer is used as clock event source to schedule wake-ups, and without this enabled all sleeps not performed through busy waiting hang the board. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by:
-
Jacopo Mondi authored
Fix 'leds' node name indent as it was wrongly aligned. Signed-off-by:
-
- 28 Sep, 2017 2 commits
-
-
Fabrizio Castro authored
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi. Also, define aliases for spi[123]. Signed-off-by:
-
Fabrizio Castro authored
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi. Also, define aliases for spi[123]. Signed-off-by:
-
- 25 Sep, 2017 1 commit
-
-
Fabrizio Castro authored
Enable the SDHI0 controller on iWave RZ/G1E carrier board. Signed-off-by:
-
- 21 Sep, 2017 5 commits
-
-
Fabrizio Castro authored
Add support for the SPI NOR device used to boot up the system to the System on Module DT. Signed-off-by:
-
Fabrizio Castro authored
Add the DT node for the QSPI interface to the SoC dtsi. Signed-off-by:
-
Fabrizio Castro authored
Add support for the SPI NOR device used to boot up the system to the System on Module DT. Signed-off-by:
-
Fabrizio Castro authored
Add the DT node for the QSPI interface to the SoC dtsi. Signed-off-by:
-
Fabrizio Castro authored
Enable the SDHI1 controller on iWave RZ/G1E SoM. Signed-off-by:
-
- 19 Sep, 2017 14 commits
-
-
Fabrizio Castro authored
Add the SDHI controllers to the r8a7745 device tree. Signed-off-by:
-
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, but audio is not yet enabled in r8a7792.dtsi, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Geert Uytterhoeven authored
Add properties to describe the reset topology for on-SoC devices: - Add the "#reset-cells" property to the CPG/MSSR device node, - Add resets and reset-names properties to the various device nodes. This allows to reset SoC devices using the Reset Controller API. Note that resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed. Signed-off-by: -
Biju Das authored
Signed-off-by:
-
Wolfram Sang authored
The WP pins are ACTIVE_HIGH, fix it in the DTS. Fixes: 2b41091b ("ARM: dts: alt: add SDHI0 and 1 support") Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Biju Das authored
Signed-off-by:
-
Biju Das authored
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to them. Signed-off-by:
-
Biju Das authored
Describe the PCI USB devices that are behind the PCI bridges, adding necessary links to the USB PHY device. Signed-off-by:
-
Biju Das authored
Define the r8a7743 generic part of the USB PHY device node. Signed-off-by:
-
Biju Das authored
Add device nodes for the r8a7743 internal PCI bridge devices. Signed-off-by:
-
Biju Das authored
Define the iWave RainboW-G22D board dependent part of the Ethernet AVB device node. On some older versions of the platform (before R4.0) the phy address may be 1 or 3. The address is fixed to 3 for R4.0 onwards (which will be the first mainstream release), hence using 3 in the dts. Signed-off-by:
-
