- 03 May, 2018 4 commits
-
-
Chris Wilson authored
As we unpark the engines and are about to begin a new cycle of activity, mark the current status of the hangceck as idle so that we avoid carrying over a stale timestamp/action into the next cycle. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180502220313.6459-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
In the unusual circumstance where we reuse a seqno (for example, in igt), make sure that we reset the hangcheck timestamp before it sees the same seqno again. References: https://bugs.freedesktop.org/show_bug.cgi?id=106215Signed-off-by:
-
Chris Wilson authored
If we try to suspend a wedged device following a GPU reset failure, we will also fail to turn off the rc6 powerwells (on vlv), leading to a *ERROR*. This is quite expected in this case, so the best we can do is shake our heads and reduce the *ERROR* to a debug so CI stops complaining. Testcase: igt/gem_eio/in-flight-suspend #vlv Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105583Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180409094905.4516-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Move the tracepoint into the common execlists_context_schedule_out() and call it from preemption completion as well. A small bit of refactoring code should help with when tracing, or else we end up with requests mysteriously disappearing and some being emitted to HW multiple times. Reported-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
-
- 02 May, 2018 10 commits
-
-
Chris Wilson authored
We need to move to a more flexible timeline that doesn't assume one fence context per engine, and so allow for a single timeline to be used across a combination of engines. This means that preallocating a fence context per engine is now a hindrance, and so we want to introduce the singular timeline. From the code perspective, this has the notable advantage of clearing up a lot of mirky semantics and some clumsy pointer chasing. By splitting the timeline up into a single entity rather than an array of per-engine timelines, we can realise the goal of the previous patch of tracking the timeline alongside the ring. v2: Tweak wait_for_idle to stop the compiling thinking that ret may be uninitialised. Signed-off-by:
-
Chris Wilson authored
In the future, we want to move a request between engines. To achieve this, we first realise that we have two timelines in effect here. The first runs through the GTT is required for ordering vma access, which is tracked currently by engine. The second is implied by sequential execution of commands inside the ringbuffer. This timeline is one that maps to userspace's expectations when submitting requests (i.e. given the same context, batch A is executed before batch B). As the rings's timelines map to userspace and the GTT timeline an implementation detail, move the timeline from the GTT into the ring itself (per-context in logical-ring-contexts/execlists, or a global per-engine timeline for the shared ringbuffers in legacy submission. The two timelines are still assumed to be equivalent at the moment (no migrating requests between engines yet) and so we can simply move from one to the other without adding extra ordering. v2: Reinforce that one isn't allowed to mix the engine execution timeline with the client timeline from userspace (on the ring). Signed-off-by:
-
Anusha Srivatsa authored
Replace 01.org URL with upstream linux-firmware repo URL. We no longer release firmware to 01.org. linux-firmware.git is the ultimate place to find the i915 firmwares. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Acked-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Chris Wilson authored
As our early doorbell is split between early allocation and a late setup after we have a channel to the GuC, it may happen due to a lapse of programmer judgement that we try to setup an invalid doorbell. Make use of our has_doorbell() function to check the doorbell does exist for the client before we try and tell the guc about it. In doing so, we prevent the compiler from warning about the otherwise unused function in some configurations. Reported-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
Michel Thierry <michel.thierry@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180501075203.12458-1-chris@chris-wilson.co.uk
-
Matthias Kaehlcke authored
Commit 39bf4de8 ("drm/i915: Add -Wall -Wextra to our build, set warnings to full") enabled extra warnings for i915 to spot possible bugs in new code, and then disabled a subset of these warnings to keep the current code building without warnings (with gcc). Enabling the extra warnings also enabled some additional clang-only warnings, as a result building i915 with clang currently is extremely noisy. For now also disable the clang warnings sign-compare, sometimes-uninitialized, unneeded-internal-declaration and initializer-overrides. If desired they can be re-enabled after the code has been fixed. Signed-off-by:
-
Chris Wilson authored
Since the advent of execlists, the HW no longer executes from a single statically assigned ring, but instead switches to a different ring for each context (logical ringbuffer contexts as it is called). So a good way to tally the executing context against what we have queued is by comparing the RING_START register against our requests. Make it so. Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180502104150.29874-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
The old wait_on_atomic_t used a custom callback to perform the schedule(), which used my return semantics of reporting an error code on timeout. wait_var_event_timeout() uses the schedule() return semantics of reporting the remaining jiffies (1 if it timed out with 0 jiffies remaining!) and 0 on failure. This semantic mismatch lead to us falsely claiming a time out occurred. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106085 Fixes: d224985a ("sched/wait, drivers/drm: Convert wait_on_atomic_t() usage to the new wait_var_event() API") Signed-off-by:
-
Jani Nikula authored
Use i915.dmc_firmware_path to override default firmware for the platform and bypassing version checks. v2: add missing param struct member declaration (David) Tested-by:
David Weinehall <david.weinehall@linux.intel.com> Reviewed-by:
-
Jani Nikula authored
Need d224985a ("sched/wait, drivers/drm: Convert wait_on_atomic_t() usage to the new wait_var_event() API") in dinq to be able to fix https://bugs.freedesktop.org/show_bug.cgi?id=106085. Signed-off-by:
-
Mika Kuoppala authored
Using plain jiffies in error state output makes the output time differences relative to the current system time. This is wrong as it makes output time differences dependent of when the error state is printed rather than when it is captured. Store capture jiffies into error state and use it when outputting the state to fix time differences output. v2: use engine timestamp as epoch, output formatting (Chris) v3: pass epoch to print_engine/request (Chris) Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
- 01 May, 2018 1 commit
-
-
Chris Wilson authored
Due to the latency of the tasklet running from ksoftirqd, by the time we process the execlist dequeue may be a long time behind the GPU. If the request was completed when we ran reschedule, we will not have tweaked its priority, but if it is still listed as being in-flight for dequeue we will use it as a reference for the rest of the queue, including requests from its own context which will now be at higher priority. This can cause us to issue a preempt-to-idle request, even though the request we want to preempt is already complete. Reported-by:
-
- 30 Apr, 2018 7 commits
-
-
Manasi Navare authored
On clock recovery this function is called to find out the max voltage swing level that we could go. However gen 9 functions use the old buffer translation tables to figure that out. ICL uses different set of tables for eDP and DP for both Combo and MG PHY ports. This patch adds the hook for ICL for getting this information from appropriate buf trans tables. v5 (from Paulo): * New rebase after changes to earlier patches. v4: * Rebase. v3: * Follow the coding conventions here (https://cgit.freedesktop.org/drm-intel/tree/Documentation/process/codin g-style.rst#n191) (Paulo) v2: * Rebase after patch that adds voltage check inside buf trans function (Rodrigo) Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-9-paulo.r.zanoni@intel.com
-
Manasi Navare authored
This is an important part of the DDI initalization as well as for changing the voltage during DisplayPort link training. The Voltage swing seqeuence is similar to Cannonlake. However it has different register definitions and hence it makes sense to create a separate vswing sequence and program functions for ICL to leave room for more changes in case the Bspec changes later and deviates from CNL sequence. v2: Use ~TAP3_DISABLE for enbaling that bit (Jani Nikula) v3: * Use dw4_scaling column for PORT_TX_DW4 values (Rodrigo) v4: * Call it combo_vswing, use switch statement (Paulo) v5 (from Paulo): * Fix a typo. * s/rate < 600000/rate <= 600000/. * Don't remove blank lines that should be there. v6: * Rebased by Rodrigo on top of Cannonlake changes where non vswing sequences are not aligned with iboost anymore. v7: Another rebase after an upstream rework. v8 (from Paulo): * Adjust the code to the upstream output type changes. * Squash the patch that moved some functions up. * Merge both get_combo_buf_trans functions in order to simplify the code. * Change the changelog format. v9 (from Paulo): * Use RTERM_SELECT instead of SCALING_MODE_SEL. * Adjust the output type handling according to how the other platforms do it now. v10 (from Paulo): * Fix comment left out from v9 changes (Rodrigo). Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: James Ausmus <james.ausmus@intel.com> Reviewed-by:
-
Chris Wilson authored
We don't need to track every ring for its lifetime as they are managed by the contexts/engines. What we do want to track are the live rings so that we can sporadically clean up requests if userspace falls behind. We can simply restrict the gt->rings list to being only gt->live_rings. v2: s/live/active/ for consistency with gt.active_requests Suggested-by:
Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
In the next patch, rings are the central timeline as requests may jump between engines. Therefore in the future as we retire in order along the engine timeline, we may retire out-of-order within a ring (as the ring now occurs along multiple engines), leading to much hilarity in miscomputing the position of ring->head. As an added bonus, retiring along the ring reduces the penalty of having one execlists client do cleanup for another (old legacy submission shares a ring between all clients). The downside is that slow and irregular (off the critical path) process of cleaning up stale requests after userspace becomes a modicum less efficient. In the long run, it will become apparent that the ordered ring->request_list matches the ring->timeline, a fun challenge for the future will be unifying the two lists to avoid duplication! v2: We need both engine-order and ring-order processing to maintain our knowledge of where individual rings have completed upto as well as knowing what was last executing on any engine. And finally by decoupling retiring the contexts on the engine and the timelines along the rings, we do have to keep a reference to the context on each request (previously it was guaranteed by the context being pinned). v3: Not just a reference to the context, but we need to keep it pinned as we manipulate the rings; i.e. we need a pin for both the manipulation of the engine state during its retirements, and a separate pin for the manipulation of the ring state. Signed-off-by:
-
Chris Wilson authored
Make life easier in upcoming patches by moving the context_pin and context_unpin vfuncs into inline helpers. v2: Fixup mock_engine to mark the context as pinned on use. Signed-off-by:
-
Chris Wilson authored
In commit 9b6586ae ("drm/i915: Keep a global seqno per-engine"), we moved from a global inflight counter to per-engine counters in the hope that will be easy to run concurrently in future. However, with the advent of the desire to move requests between engines, we do need a global counter to preserve the semantics that no engine wraps in the middle of a submit. (Although this semantic is now only required for gen7 semaphore support, which only supports greater-then comparisons!) v2: Keep a global counter of all requests ever submitted and force the reset when it wraps. References: 9b6586ae ("drm/i915: Keep a global seqno per-engine") Signed-off-by:
-
Chris Wilson authored
Previously, we just reset the ring register in the context image such that we could skip over the broken batch and emit the closing breadcrumb. However, on resume the context image and GPU state would be reloaded, which may have been left in an inconsistent state by the reset. The presumption was that at worst it would just cause another reset and skip again until it recovered, however it seems just as likely to cause an unrecoverable hang. Instead of risking loading an incomplete context image, restore it back to the default state. v2: Fix up off-by-one from including the ppHSWP in with the register state. v3: Use a ring local to compact a few lines. v4: Beware setting the ring local before checking for a NULL request. References: https://bugs.freedesktop.org/show_bug.cgi?id=105304Signed-off-by:
-
- 29 Apr, 2018 7 commits
-
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
drm-misc-next for v4.18: UAPI Changes: - Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime) Core Changes: - Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville) - mode_valid return type fixes. (Luc) - Handle zpos normalization in the core. (Peter) Driver Changes: - Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan) - Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas) - Add support for MIPI DSI to sun4i. (Maxime) Signed-off-by:
Dave Airlie <airlied@redhat.com> # gpg: Signature made Thu 26 Apr 2018 08:21:01 PM AEST # gpg: using RSA key FE558C72A67013C3 # gpg: Can't check signature: public key not found Link: https://patchwork.freedesktop.org/patch/msgid/b33da7eb-efc9-ae6f-6f69-b7acd6df6797@mblankhorst.nl
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "Another set of x86 related updates: - Fix the long broken x32 version of the IPC user space headers which was noticed by Arnd Bergman in course of his ongoing y2038 work. GLIBC seems to have non broken private copies of these headers so this went unnoticed. - Two microcode fixlets which address some more fallout from the recent modifications in that area: - Unconditionally save the microcode patch, which was only saved when CPU_HOTPLUG was enabled causing failures in the late loading mechanism - Make the later loader synchronization finally work under all circumstances. It was exiting early and causing timeout failures due to a missing synchronization point. - Do not use mwait_play_dead() on AMD systems to prevent excessive power consumption as the CPU cannot go into deep power states from there. - Address an annoying sparse warning due to lost type qualifiers of the vmemmap and vmalloc base address constants. - Prevent reserving crash kernel region on Xen PV as this leads to the wrong perception that crash kernels actually work there which is not the case. Xen PV has its own crash mechanism handled by the hypervisor. - Add missing TLB cpuid values to the table to make the printout on certain machines correct. - Enumerate the new CLDEMOTE instruction - Fix an incorrect SPDX identifier - Remove stale macros" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds x86/setup: Do not reserve a crash kernel region if booted on Xen PV x86/cpu/intel: Add missing TLB cpuid values x86/smpboot: Don't use mwait_play_dead() on AMD systems x86/mm: Make vmemmap and vmalloc base address constants unsigned long x86/vector: Remove the unused macro FPU_IRQ x86/vector: Remove the macro VECTOR_OFFSET_START x86/cpufeatures: Enumerate cldemote instruction x86/microcode: Do not exit early from __reload_late() x86/microcode/intel: Save microcode patch unconditionally x86/jailhouse: Fix incorrect SPDX identifier -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 pti fixes from Thomas Gleixner: "A set of updates for the x86/pti related code: - Preserve r8-r11 in int $0x80. r8-r11 need to be preserved, but the int$80 entry code removed that quite some time ago. Make it correct again. - A set of fixes for the Global Bit work which went into 4.17 and caused a bunch of interesting regressions: - Triggering a BUG in the page attribute code due to a missing check for early boot stage - Warnings in the page attribute code about holes in the kernel text mapping which are caused by the freeing of the init code. Handle such holes gracefully. - Reduce the amount of kernel memory which is set global to the actual text and do not incidentally overlap with data. - Disable the global bit when RANDSTRUCT is enabled as it partially defeats the hardening. - Make the page protection setup correct for vma->page_prot population again. The adjustment of the protections fell through the crack during the Global bit rework and triggers warnings on machines which do not support certain features, e.g. NX" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/entry/64/compat: Preserve r8-r11 in int $0x80 x86/pti: Filter at vma->vm_page_prot population x86/pti: Disallow global kernel text with RANDSTRUCT x86/pti: Reduce amount of kernel text allowed to be Global x86/pti: Fix boot warning from Global-bit setting x86/pti: Fix boot problems from Global-bit setting -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "Two fixes from the timer departement: - Fix a long standing issue in the NOHZ tick code which causes RB tree corruption, delayed timers and other malfunctions. The cause for this is code which modifies the expiry time of an enqueued hrtimer. - Revert the CLOCK_MONOTONIC/CLOCK_BOOTTIME unification due to regression reports. Seems userspace _is_ relying on the documented behaviour despite our hope that it wont" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME tick/sched: Do not mess with an enqueued hrtimer -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "The perf update contains the following bits: x86: - Prevent setting freeze_on_smi on PerfMon V1 CPUs to avoid #GP perf stat: - Keep the '/' event modifier separator in fallback, for example when fallbacking from 'cpu/cpu-cycles/' to user level only, where it should become 'cpu/cpu-cycles/u' and not 'cpu/cpu-cycles/:u' (Jiri Olsa) - Fix PMU events parsing rule, improving error reporting for invalid events (Jiri Olsa) - Disable write_backward and other event attributes for !group events in a group, fixing, for instance this group: '{cycles,msr/aperf/}:S' that has leader sampling (:S) and where just the 'cycles', the leader event, should have the write_backward attribute set, in this case it all fails because the PMU where 'msr/aperf/' lives doesn't accepts write_backward style sampling (Jiri Olsa) - Only fall back group read for leader (Kan Liang) - Fix core PMU alias list for x86 platform (Kan Liang) - Print out hint for mixed PMU group error (Kan Liang) - Fix duplicate PMU name for interval print (Kan Liang) Core: - Set main kernel end address properly when reading kernel and module maps (Namhyung Kim) perf mem: - Fix incorrect entries and add missing man options (Sangwon Hong) s/390: - Remove s390 specific strcmp_cpuid_cmp function (Thomas Richter) - Adapt 'perf test' case record+probe_libc_inet_pton.sh for s390 - Fix s390 undefined record__auxtrace_init() return value in 'perf record' (Thomas Richter)" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Don't enable freeze-on-smi for PerfMon V1 perf stat: Fix duplicate PMU name for interval print perf evsel: Only fall back group read for leader perf stat: Print out hint for mixed PMU group error perf pmu: Fix core PMU alias list for X86 platform perf record: Fix s390 undefined record__auxtrace_init() return value perf mem: Document incorrect and missing options perf evsel: Disable write_backward for leader sampling group events perf pmu: Fix pmu events parsing rule perf stat: Keep the / modifier separator in fallback perf test: Adapt test case record+probe_libc_inet_pton.sh for s390 perf list: Remove s390 specific strcmp_cpuid_cmp function perf machine: Set main kernel end address properly -
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Fix misc bugs and a regression for ext4" * tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: add MODULE_SOFTDEP to ensure crc32c is included in the initramfs ext4: fix bitmap position validation ext4: set h_journal if there is a failure starting a reserved handle ext4: prevent right-shifting extents beyond EXT_MAX_BLOCKS
-
- 28 Apr, 2018 10 commits
-
-
Amir Goldstein authored
The comment claims that this helper will try not to loose bits, but for 64bit long it looses the high bits before hashing 64bit long into 32bit int. Use the helper hash_long() to do the right thing for 64bit long. For 32bit long, there is no change. All the callers of end_name_hash() either assign the result to qstr->hash, which is u32 or return the result as an int value (e.g. full_name_hash()). Change the helper return type to int to conform to its users. [ It took me a while to apply this, because my initial reaction to it was - incorrectly - that it could make for slower code. After having looked more at it, I take back all my complaints about the patch, Amir was right and I was mis-reading things or just being stupid. I also don't worry too much about the possible performance impact of this on 64-bit, since most architectures that actually care about performance end up not using this very much (the dcache code is the most performance-critical, but the word-at-a-time case uses its own hashing anyway). So this ends up being mostly used for filesystems that do their own degraded hashing (usually because they want a case-insensitive comparison function). A _tiny_ worry remains, in that not everybody uses DCACHE_WORD_ACCESS, and then this potentially makes things more expensive on 64-bit architectures with slow or lacking multipliers even for the normal case. That said, realistically the only such architecture I can think of is PA-RISC. Nobody really cares about performance on that, it's more of a "look ma, I've got warts^W an odd machine" platform. So the patch is fine, and all my initial worries were just misplaced from not looking at this properly. - Linus ] Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Sterba authored
The AFFS filesystem is still in use by m68k community (Link #2), but as there was no code activity and no maintainer, the filesystem appeared on the list of candidates for staging/removal (Link #1). I volunteer to act as a maintainer of AFFS to collect any fixes that might show up and to guard fs/affs/ against another spring cleaning. Link: https://lkml.kernel.org/r/20180425154602.GA8546@bombadil.infradead.org Link: https://lkml.kernel.org/r/1613268.lKBQxPXt8J@merkaba CC: Martin Steigerwald <martin@lichtvoll.de> CC: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: - two driver fixes - better parameter check for the core - Documentation updates - part of a tree-wide HAS_DMA cleanup * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: sprd: Fix the i2c count issue i2c: sprd: Prevent i2c accesses after suspend is called i2c: dev: prevent ZERO_SIZE_PTR deref in i2cdev_ioctl_rdwr() Documentation/i2c: adopt kernel commenting style in examples Documentation/i2c: sync docs with current state of i2c-tools Documentation/i2c: whitespace cleanup i2c: Remove depends on HAS_DMA in case of platform dependency
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fixes from Herbert Xu: - crypto API regression that may cause sporadic alloc failures - double-free bug in drbg * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: drbg - set freed buffers to NULL crypto: api - fix finding algorithm currently being tested
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "A few security related fixes for SMB3, most importantly for SMB3.11 encryption" * tag '4.17-rc2-smb3' of git://git.samba.org/sfrench/cifs-2.6: cifs: smbd: Avoid allocating iov on the stack cifs: smbd: Don't use RDMA read/write when signing is used SMB311: Fix reconnect SMB3: Fix 3.11 encryption to Windows and handle encrypted smb3 tcon CIFS: set *resp_buf_type to NO_BUFFER on error
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: "A bunch of fixes, mostly for existing code and going to stable. Our memory hot-unplug path wasn't flushing the cache before removing memory. That is a problem now that we are doing memory hotplug on bare metal. Three fixes for the NPU code that supports devices connected via NVLink (ie. GPUs). The main one tweaks the TLB flush algorithm to avoid soft lockups for large flushes. A fix for our memory error handling where we would loop infinitely, returning back to the bad access and hard lockup the CPU. Fixes for the OPAL RTC driver, which wasn't handling some error cases correctly. A fix for a hardlockup in the powernv cpufreq driver. And finally two fixes to our smp_send_stop(), required due to a recent change to use it on shutdown. Thanks to: Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh Salgaonkar, Mark Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri G Bhat" * tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/kvm/booke: Fix altivec related build break powerpc: Fix deadlock with multiple calls to smp_send_stop cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt powerpc: Fix smp_send_stop NMI IPI handling rtc: opal: Fix OPAL RTC driver OPAL_BUSY loops powerpc/mce: Fix a bug where mce loops on memory UE. powerpc/powernv/npu: Do a PID GPU TLB flush when invalidating a large address range powerpc/powernv/npu: Prevent overwriting of pnv_npu2_init_contex() callback parameters powerpc/powernv/npu: Add lock to prevent race in concurrent context init/destroy powerpc/powernv/memtrace: Let the arch hotunplug code flush cache powerpc/mm: Flush cache on memory hot(un)plug
-
Paulo Zanoni authored
There's a lot of code for the PLL enabling, so let's first only introduce the register definitions in order to make patch reviewing a little easier. v2: Coding style (Jani). v3: Preparation for upstreaming. v4: Fix MG_CLKTOP2_CORECLKCTL1 address and random typos (James). Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by:
James Ausmus <james.ausmus@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-3-paulo.r.zanoni@intel.com
-
Mahesh Kumar authored
Gen11/ICL onward ddb entry start/end mask is increased from 10 bits to 11 bits. This patch make changes to use proper mask for ICL+ during hardware ddb value readout. Changes since V1: - Use _MASK & _SHIFT macro (James) Changes since V2: - use kernel type u8 instead of uint8_t Changes since V3: - Rebase Signed-off-by:
Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by:
-
Mahesh Kumar authored
ICL has two slices of DBuf, each slice of size 1024 blocks. We should not always enable slice-2. It should be enabled only if display total required BW is > 12GBps OR more than 1 pipes are enabled. Changes since V1: - typecast total_data_rate to u64 before multiplication to solve any possible overflow (Rodrigo) - fix where skl_wm_get_hw_state was memsetting ddb, resulting enabled_slices to become zero - Fix the logic of calculating ddb_size Changes since V2: - If no-crtc is part of commit required_slices will have value "0", don't try to disable DBuf slice. Changes since V3: - Create a generic helper to enable/disable slice - don't return early if total_data_rate is 0, it may be cursor only commit, or atomic modeset without any plane. Changes since V4: - Solve checkpatch warnings - use kernel types u8/u64 instead of uint8_t/uint64_t Changes since V5: - Rebase Signed-off-by:
-
Mahesh Kumar authored
This patch adds support to start tracking status of DBUF slices. This is foundation to introduce support for enabling/disabling second DBUF slice dynamically for ICL. Changes Since V1: - use kernel type u8 over uint8_t Signed-off-by:
-
- 27 Apr, 2018 1 commit
-
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fixes from Radim Krčmář: "ARM: - PSCI selection API, a leftover from 4.16 (for stable) - Kick vcpu on active interrupt affinity change - Plug a VMID allocation race on oversubscribed systems - Silence debug messages - Update Christoffer's email address (linaro -> arm) x86: - Expose userspace-relevant bits of a newly added feature - Fix TLB flushing on VMX with VPID, but without EPT" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: x86/headers/UAPI: Move DISABLE_EXITS KVM capability bits to the UAPI kvm: apic: Flush TLB after APIC mode/address change if VPIDs are in use arm/arm64: KVM: Add PSCI version selection API KVM: arm/arm64: vgic: Kick new VCPU on interrupt migration arm64: KVM: Demote SVE and LORegion warnings to debug only MAINTAINERS: Update e-mail address for Christoffer Dall KVM: arm/arm64: Close VMID generation race
-
