[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.

[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
   so that it is passed in by driver during DMCU initn
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.

Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.

[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.

If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

* Pull duplicate audio_clock_info struct to stream_encoder.h
* Generalize sec_gsp7* to sec_gsp_pps*
* Expose enc1 and enc2 stream encoder audio funcs
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description] This is cause by failing to read link caps from driver.
Signed-off-by: Daniel He <daniel.he@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.

[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
Value read from SMU is 16 bits, not 32.

[How]
Fix type, and add wm_type enum in preparation for future interfaces.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.

Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.

Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.

We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.

[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
during It's possible to call dcn_validate_bandwidth with no plane.
In that case, as we are only intersted in if output timing is supported or not,
even if we cannot support native resolution, we still want to support lower
resolution if it is valid

[how]
if there exist no surface, make viewport/rec_out size at max 1080p. It is
already known that 1080p x 6(max # of pipes) is supported, so if we fail
validation, it is because of the stream
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
by adding fast_validate flag, we are skipping some portion of
dcn_validate_bandwidth code that is not necessary for mode validation.
However we have a bug where it does not calculate
v->total_data_read_bandwidth, which is one of the factors determines the
result of the validation, and therefore report false positive during
mode validation.

[how]
add calculation of v->total_data_read_bandwidth outside of the region
that is guarded by fast_validate flag
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
link-specific functions should reside in dc_link.c

[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add min_dcfclk_mhz to bounding box overrides.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Better organization

[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
1. DMCU is not running on some platform but driver still send ABM
   command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable

[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
   determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.

[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GSL is a form of locking that can be used to synchronize pipes in a
pipe-split configurations when async flip is used. Add the registers
here.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.

[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
stream id should uniquely identify an instance of stream.
the copy constructor should be treated as a new
stream instance.

[how]
assign a new stream id in this copy constructor.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D
(unless we know 1D LUT is identity), so we never want to return here early.
We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is
called near the end of that function.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.

[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As it will destroy clear_state_obj, and also will unpin it in the
gfx_v9_0_sw_fini, so don't need to
call amdgpu_bo_free_kernel in gfx_v9_0_sw_fini, or it will have unpin warning.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

injection need a valid gpu address.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

New stuff for 5.3:
- Add new thermal sensors for vega asics
- Various RAS fixes
- Add sysfs interface for memory interface utilization
- Use HMM rather than mmu notifier for user pages
- Expose xgmi topology via kfd
- SR-IOV fixes
- Fixes for manual driver reload
- Add unique identifier for vega asics
- Clean up user fence handling with UVD/VCE/VCN blocks
- Convert DC to use core bpc attribute rather than a custom one
- Add GWS support for KFD
- Vega powerplay improvements
- Add CRC support for DCE 12
- SR-IOV support for new security policy
- Various cleanups

From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529220944.14464-1-alexander.deucher@amd.com

The pointer dev is set to null yet it is being dereferenced when
checking dev->dqm->sched_policy.  Fix this by performing the check
on dev->dqm->sched_policy after dev has been assigned and null
checked.  Also remove the redundant null assignment to dev.

Addresses-Coverity: ("Explicit null dereference")
Fixes: 1a058c33 ("drm/amdkfd: New IOCTL to allocate queue GWS")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For passthrough, after rebooted the VM, driver will do
a baco reset before doing other driver initialization during loading
 driver. For doing the baco reset, it will first
check the baco reset capability. So first need to set the
cap from the vbios information or baco reset won't be
enabled.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Not necessary on soc15 and breaks driver reload on server cards.
Acked-by: Amber Lin <Amber.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Flora Cui <Flora.Cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add a field in map_queues packet to indicate whether
this is a gws control queue. Only one queue per process
can be gws control queue. Change num_gws field in
map_process packet to 7 bits
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add a new kfd ioctl to allocate queue GWS. Queue
GWS is released on queue destroy.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add functions in process queue manager to
set/unset queue gws. Also set process's number
of gws used. Currently only one queue in
process can use and use all gws.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GWS bo is shared between all kfd processes. Add function to add gws
to kfd process's bo list so gws can be evicted from and restored
for process.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On device initialization, KFD allocates all (64) gws which
is shared by all KFD processes.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add amdgpu_amdkfd interface to alloc and free gws
from amdgpu
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add amdgpu_amdkfd interface to get num_gws and add num_gws
to /sys/class/kfd/kfd/topology/nodes/x/properties. Only report
num_gws if MEC FW support GWS barriers. Currently it is
determined by a module parameter which will be replaced
with MEC FW version check when firmware is ready.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

TTM doesn't support CPU mapping of sg type bo (under which
mmio bo is created). Switch mmaping of mmio page to kfd
device file.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

dc_destroy should be called amdgpu_cgs_destroy_device,
as it will use cgs context to read or write registers.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Features:
- Engine discovery query (Tvrtko)
- Support for DP YCbCr4:2:0 outputs (Gwan-gyeong)
- HDCP revocation support, refactoring (Ramalingam)
- Remove DRM_AUTH from IOCTLs which also have DRM_RENDER_ALLOW (Christian König)
- Asynchronous display power disabling (Imre)
- Perma-pin uC firmware and re-enable global reset (Fernando)
- GTT remapping for display, for bigger fb size and stride (Ville)
- Enable pipe HDR mode on ICL if only HDR planes are used (Ville)
- Kconfig to tweak the busyspin durations for i915_wait_request (Chris)
- Allow multiple user handles to the same VM (Chris)
- GT/GEM runtime pm improvements using wakerefs (Chris)
- Gen 4&5 render context support (Chris)
- Allow userspace to clone contexts on creation (Chris)
- SINGLE_TIMELINE flags for context creation (Chris)
- Allow specification of parallel execbuf (Chris)

Refactoring:
- Header refactoring (Jani)
- Move GraphicsTechnology files under gt/ (Chris)
- Sideband code refactoring (Chris)

Fixes:
- ICL DSI state readout and checker fixes (Vandita)
- GLK DSI picture corruption fix (Stanislav)
- HDMI deep color fixes (Clinton, Aditya)
- Fix driver unbinding from a device in use (Janusz)
- Fix clock gating with pipe scaling (Radhakrishna)
- Disable broken FBC on GLK (Daniel Drake)
- Miscellaneous GuC fixes (Michal)
- Fix MG PHY DP register programming (Imre)
- Add missing combo PHY lane power setup (Imre)
- Workarounds for early ICL VBT issues (Imre)
- Fix fastset vs. pfit on/off on HSW EDP transcoder (Ville)
- Add readout and state check for pch_pfit.force_thru (Ville)
- Miscellaneous display fixes and refactoring (Ville)
- Display workaround fixes (Ville)
- Enable audio even if ELD is bogus (Ville)
- Fix use-after-free in reporting create.size (Chris)
- Sideband fixes to avoid BYT hard lockups (Chris)
- Workaround fixes and improvements (Chris)

Maintainer shortcomings:
- Failure to adequately describe and give credit for all changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87sgt3n45z.fsf@intel.com