Actually we can use the "clk" in the struct sdhci_pltfm_host.
With this change we can also kill the private function for get
max clock in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Simplify the error and remove path.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is only one "clk" member in this driver specific private struct.
Actually we can use the "clk" member in the struct sdhci_pltfm_host,
and then kill this struct completely.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The function clk_disable_unprepare() already take care of either error
or null cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the original tuning code, delay value is set to SD Bus Clock Delay
Register (SD_CLK_DELAY_SETTING) as (val | (Val << 7) | (val << 16)),
which means CLK_DELAY_IN1, CLK_DELAY_IN2 and CLK_DELAY_OUT are the
same and with 128 steps. This is doubtful. In CSR design specification
documents CS-304575-DR-3H, this issue is clarified, the delay[13:0] in
SD_CLK_DELAY_SETTING is simplied to the concatenation of {CLK_DELAY_IN2,
CLK_DELAY_IN1}.
Besides, for CMD19 tuning, no need to set CLK_DELAY_OUT([22,16]
of SD_CLK_DELAY_SETTING).
Signed-off-by: weijun yang <york.yang@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We really don't want to get a card detect interrupt during probe time
since it can confuse things.  Let's disable the card detect interrupt
until we're in a really good place: the end of probe.  Let's also
simply avoid enabling the card detect interrupt if it's not used.

It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt.  That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host().  On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children.  I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:

Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host

Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.

The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.

We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command.  This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.

Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We should give dw_mmc a good reset after we apply power.  On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.

Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It appears that we can confuse things if we try to turn on the MMC
clock when the power is off.  Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The STOP command can terminate a data transfer between a memory card and
mmc controller.

As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.

After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
  which depends on MMC_CAP_RUNTIME_RESUME capability.

On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.

And the total tuning time will be more than 400ms.

So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull bugfix for md from Neil Brown:
 "One fix for md in 4.0-rc4

  Regression in recent patch causes crash on error path"

* tag 'md/4.0-rc4-fix' of git://neil.brown.name/md:
  md: fix problems with freeing private data after ->run failure.

Pull driver core fixes from Greg KH:
 "Here are two bugfixes for things reported.  One regression in kernfs,
  and another issue fixed in the LZ4 code that was fixed in the
  "upstream" codebase that solves a reported kernel crash

  Both have been in linux-next for a while"

* tag 'driver-core-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  LZ4 : fix the data abort issue
  kernfs: handle poll correctly on 'direct_read' files.

Pull char/misc fixes from Greg KH:
 "Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
  were merged in 4.0-rc1 that cause regressions.  So let's revert them
  for now and they will be reworked and resent sometime in the future.

  All have been tested in linux-next for a while"

* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "pcmcia: add a new resource manager for non ISA systems"
  Revert "pcmcia: fix incorrect bracketing on a test"
  Revert "pcmcia: add missing include for new pci resource handler"

Pull staging driver fixes from Greg KH:
 "Here are four small staging driver fixes, all for the vt6656 and
  vt6655 drivers, that resolve some reported issues with them.

  All of these patches have been in linux next for a while"

* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  vt6655: Fix late setting of byRFType.
  vt6655: RFbSetPower fix missing rate RATE_12M
  staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
  staging: vt6655: vnt_tx_packet fix dma_idx selection.

Pull tty/serial driver fix from Greg KH:
 "Here's a single 8250 serial driver that fixes a reported deadlock with
  the serial console and the tty driver.

  It's been in linux-next for a while now"

* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_dw: Fix deadlock in LCR workaround

Pull USB / PHY driver fixes from Greg KH:
 "Here's a number of USB and PHY driver fixes for 4.0-rc5.

  The largest thing here is a revert of a gadget function driver patch
  that removes 500 lines of code.  Other than that, it's a number of
  reported bugs fixes and new quirk/id entries.

  All have been in linux-next for a while"

* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: common: otg-fsm: only signal connect after switching to peripheral
  uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
  USB: ehci-atmel: rework clk handling
  MAINTAINERS: add entry for USB OTG FSM
  usb: chipidea: otg: add a_alt_hnp_support response for B device
  phy: omap-usb2: Fix missing clk_prepare call when using old dt name
  phy: ti/omap: Fix modalias
  phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
  phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
  phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
  phy: twl4030-usb: Remove redundant assignment for twl->linkstat
  phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
  phy: Find the right match in devm_phy_destroy()
  phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
  phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
  phy: samsung-usb2: Remove NULL terminating entry from phys array
  phy: hix5hd2-sata: Check return value of platform_get_resource
  phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
  Revert "usb: gadget: zero: Add support for interrupt EP"
  Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
  ...

Pull slave dmaengine fixes from Vinod Koul:
 "Four fixes for dw, pl08x, imx-sdma and at_hdmac driver.  Nothing
  unusual here, simple fixes to these drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: pl08x: Define capabilities for generic capabilities reporting
  dmaengine: dw: append MODULE_ALIAS for platform driver
  dmaengine: imx-sdma: switch to dynamic context mode after script loaded
  dmaengine: at_hdmac: Fix calculation of the residual bytes

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are fixes for recent regressions (PCI/ACPI resources and at91
  RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
  cpuidle fixes (one stable-candidate too).

  Specifics:

   - Revert a recent PCI commit related to IRQ resources management that
     introduced a regression for drivers attempting to bind to devices
     whose previous drivers did not balance pci_enable_device() and
     pci_disable_device() as expected (Rafael J Wysocki).

   - Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
     recent commit related to wakeup interrupt handling (Dan Carpenter).

   - Allow the power capping RAPL (Running-Average Power Limit) driver
     to use different energy units for domains within one CPU package
     which is necessary to handle Intel Haswell EP processors correctly
     (Jacob Pan).

   - Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
     updating the target residency and exit latency numbers for those
     chips (Sebastien Rannou).

   - Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
     in a row before cpu_pm_exit() is called on the same CPU which
     breaks the core's assumptions regarding the usage of those
     functions (Gregory Clement)"

* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "x86/PCI: Refine the way to release PCI IRQ resources"
  rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
  powercap / RAPL: handle domains with different energy units
  cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
  cpuidle: mvebu: Fix the CPU PM notifier usage

Pull drm updates from Dave Airlie:
 "A bunch of fixes across drivers:

  radeon:
     disable two ended allocation for now, it breaks some stuff

  amdkfd:
     misc fixes

  nouveau:
     fix irq loop problem, add basic support for GM206 (new hw)

  i915:
     fix some WARNs people were seeing

  exynos:
     fix some iommu interactions causing boot failures"

* git://people.freedesktop.org/~airlied/linux:
  drm/radeon: drop ttm two ended allocation
  drm/exynos: fix the initialization order in FIMD
  drm/exynos: fix typo config name correctly.
  drm/exynos: Check for NULL dereference of crtc
  drm/exynos: IS_ERR() vs NULL bug
  drm/exynos: remove unused files
  drm/i915: Make sure the primary plane is enabled before reading out the fb state
  drm/nouveau/bios: fix i2c table parsing for dcb 4.1
  drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
  drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
  drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
  drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
  drm/radeon: Changing number of compute pipe lines
  drm/amdkfd: Fix SDMA queue init. in non-HWS mode
  drm/amdkfd: destroy mqd when destroying kernel queue
  drm/i915: Ensure plane->state->fb stays in sync with plane->fb

Merge tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull more DeviceTree fixes vfom Rob Herring:

 - revert setting stdout-path as preferred console.  This caused
   regressions in PowerMACs and other systems.

 - yet another fix for stdout-path option parsing.

 - fix error path handling in of_irq_parse_one

* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  Revert "of: Fix premature bootconsole disable with 'stdout-path'"
  of: handle both '/' and ':' in path strings
  of: unittest: Add option string test case with longer path
  of/irq: Fix of_irq_parse_one() returned error codes

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are current target-pending fixes for v4.0-rc5 code that have made
  their way into the queue over the last weeks.

  The fixes this round include:

   - Fix long-standing iser-target logout bug related to early
     conn_logout_comp completion, resulting in iscsi_conn use-after-tree
     OOpsen.  (Sagi + nab)

   - Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
     handing for DDP hw offload.  (DanC)

   - Fix incorrect use of unprotected __transport_register_session() in
     tcm_qla2xxx + other single local se_node_acl fabrics.  (Bart)

   - Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
     for ack_kref=1 failure path.  (Bart)

   - Fix pSCSI backend ->get_device_type() statistics OOPs with
     un-configured device.  (Olaf + nab)

   - Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
     time.  (Claudio + nab)

   - Fix FUA write false positive failure regression in v4.0-rc1 code.
     (Christophe Vu-Brugier + HCH)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
  target: Fix virtual LUN=0 target_configure_device failure OOPs
  target/pscsi: Fix NULL pointer dereference in get_device_type
  tcm_fc: missing curly braces in ft_invl_hw_context()
  target: Fix reference leak in target_get_sess_cmd() error path
  loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
  tcm_qla2xxx: Fix incorrect use of __transport_register_session
  iscsi-target: Avoid early conn_logout_comp for iser connections
  Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
  target: Disallow changing of WRITE cache/FUA attrs after export

Pull devicemapper fixes from Mike Snitzer:
 "A handful of stable fixes for DM:
   - fix thin target to always zero-fill reads to unprovisioned blocks
   - fix to interlock device destruction's suspend from internal
     suspends
   - fix 2 snapshot exception store handover bugs
   - fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing"

* tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME
  dm snapshot: suspend merging snapshot when doing exception handover
  dm snapshot: suspend origin when doing exception handover
  dm: hold suspend_lock while suspending device during device deletion
  dm thin: fix to consistently zero-fill reads to unprovisioned blocks

Pull btrfs fixes from Chris Mason:
 "Most of these are fixing extent reservation accounting, or corners
  with tree writeback during commit.

  Josef's set does add a test, which isn't strictly a fix, but it'll
  keep us from making this same mistake again"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix outstanding_extents accounting in DIO
  Btrfs: add sanity test for outstanding_extents accounting
  Btrfs: just free dummy extent buffers
  Btrfs: account merges/splits properly
  Btrfs: prepare block group cache before writing
  Btrfs: fix ASSERT(list_empty(&cur_trans->dirty_bgs_list)
  Btrfs: account for the correct number of extents for delalloc reservations
  Btrfs: fix merge delalloc logic
  Btrfs: fix comp_oper to get right order
  Btrfs: catch transaction abortion after waiting for it
  btrfs: fix sizeof format specifier in btrfs_check_super_valid()

Pull nfsd bufix from Bruce Fields:
 "This is a fix for a crash easily triggered by 4.1 activity to a server
  built with CONFIG_NFSD_PNFS.

  There are some more bugfixes queued up that I intend to pass along
  next week, but this is the most critical"

* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
  Subject: nfsd: don't recursively call nfsd4_cb_layout_fail

Pull UBI fix from Artem Bityutskiy:
 "This fixes a bug introduced during the v4.0 merge window where we
  forgot to put braces where they should be"

* tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs:
  UBI: fix missing brace control flow

Pull arm64 fixes from Catalin Marinas:

 - mm switching fix where the kernel pgd ends up in the user TTBR0 after
   returning from an EFI run-time services call

 - fix __GFP_ZERO handling for atomic pool and CMA DMA allocations (the
   generic code does get the gfp flags, so it's left with the arch code
   to memzero accordingly)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Honor __GFP_ZERO in dma allocations
  arm64: efi: don't restore TTBR0 if active_mm points at init_mm

Pull ARM fixes from Russell King:
 "Another few ARM fixes.  Fabrice fixed the L2 cache DT parsing to allow
  prefetch configuration to be specified even when the cache size
  parsing fails.

  Laura noticed that the setting of page attributes wasn't working for
  modules due to is_module_addr() always returning false.

  Marc Gonzalez (aka Mason) noticed a potential latent bug with the way
  we read one of the CPUID registers (where we could attempt to read a
  non-present CPUID register which may fault.)

  I've fixed an issue where 32-bit DMA masks were failing with memory
  which extended to the top of physical address space, and I've also
  added debugging output of the page tables when we hit a data access
  exception which we don't specifically handle - prompted by the lack of
  information in a bug report"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8313/1: Use read_cpuid_ext() macro instead of inline asm
  ARM: 8311/1: Don't use is_module_addr in setting page attributes
  ARM: 8310/1: l2c: Fix prefetch settings dt parsing
  ARM: dump pgd, pmd and pte states on unhandled data abort faults
  ARM: dma-api: fix off-by-one error in __dma_supported()

* pm-cpuidle:
  cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
  cpuidle: mvebu: Fix the CPU PM notifier usage

* powercap:
  powercap / RAPL: handle domains with different energy units

* irq-pm:
  rtc: at91rm9200: double locking bug in at91_rtc_interrupt()

* acpi-resources:
  Revert "x86/PCI: Refine the way to release PCI IRQ resources"

If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.

However:
  md.c calls ->free() even if ->private_data is NULL, which
     causes problems in some personalities.
  raid0.c frees the data, but doesn't clear ->private_data,
     which will become a problem when we fix md.c

So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 5aa61f42
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381Signed-off-by: NeilBrown <neilb@suse.de>

Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.

Cc: <stable@vger.kernel.org> # v3.14+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

init_mm isn't a normal mm: it has swapper_pg_dir as its pgd (which
contains kernel mappings) and is used as the active_mm for the idle
thread.

When restoring the pgd after an EFI call, we write current->active_mm
into TTBR0. If the current task is actually the idle thread (e.g. when
initialising the EFI RTC before entering userspace), then the TLB can
erroneously populate itself with junk global entries as a result of
speculative table walks.

When we do eventually return to userspace, the task can end up hitting
these junk mappings leading to lockups, corruption or crashes.

This patch fixes the problem in the same way as the CPU suspend code by
ensuring that we never switch to the init_mm in efi_set_pgd and instead
point TTBR0 at the zero page. A check is also added to cpu_switch_mm to
BUG if we get passed swapper_pg_dir.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: f3cdfd23 ("arm64/efi: move SetVirtualAddressMap() to UEFI stub")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit b4b55cda (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.

This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device().  That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.

Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Backporting a couple of plane related fixes from drm-next to v4.0.

* tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Make sure the primary plane is enabled before reading out the fb state
  drm/i915: Ensure plane->state->fb stays in sync with plane->fb

Merge tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes

- Fixing SDMA initialization when in non-HWS mode (debug mode)
- Memory leak fix when destroying kernel queue
- Fix number of available compute pipelines according to new firmware

* tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux:
  drm/radeon: Changing number of compute pipe lines
  drm/amdkfd: Fix SDMA queue init. in non-HWS mode
  drm/amdkfd: destroy mqd when destroying kernel queue

A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:

  fde9f50f target: Add sanity checks for DPO/FUA bit usage

The condition is as follows:

  if (!dev->dev_attrib.emulate_fua_write ||
      !dev->dev_attrib.emulate_write_cache)

However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.

This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.

Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.

To address this bug originally introduced by commit 0fd97ccf, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>