OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).

The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).

This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).

Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.

This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.

Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add new properties to the rt5651 dt-bindings for configuring the
jack-detect source and over-current detect settings.

Cc: devicetree@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.

But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.

This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.

For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.

Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection

This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.

Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.

Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.

This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.

rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.

This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.

This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.

This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.

RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.

This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.

This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.

Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().

This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.

This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now we can replace Codec to Component. Let's do it.

Note:
	xxx_codec_xxx()		->	xxx_component_xxx()
	.idle_bias_off = 1	->	.idle_bias_on = 0
	.ignore_pmdown_time = 0	->	.use_pmdown_time = 1
	-			->	.endianness = 1
	-			->	.non_legacy_dai_naming = 1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

except, again, POLLFREE and POLL_BUSY_LOOP.

With this, we finally get to the promised end result:

 - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
   stray instances of ->poll() still using those will be caught by
   sparse.

 - eventpoll.c and select.c warning-free wrt __poll_t

 - no more kernel-side definitions of POLL... - userland ones are
   visible through the entire kernel (and used pretty much only for
   mangle/demangle)

 - same behavior as after the first series (i.e. sparc et.al. epoll(2)
   working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more poll annotation updates from Al Viro:
 "This is preparation to solving the problems you've mentioned in the
  original poll series.

  After this series, the kernel is ready for running

      for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
            L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
            for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
      done

  as a for bulk search-and-replace.

  After that, the kernel is ready to apply the patch to unify
  {de,}mangle_poll(), and then get rid of kernel-side POLL... uses
  entirely, and we should be all done with that stuff.

  Basically, that's what you suggested wrt KPOLL..., except that we can
  use EPOLL... instead - they already are arch-independent (and equal to
  what is currently kernel-side POLL...).

  After the preparations (in this series) switch to returning EPOLL...
  from ->poll() instances is completely mechanical and kernel-side
  POLL... can go away. The last step (killing kernel-side POLL... and
  unifying {de,}mangle_poll() has to be done after the
  search-and-replace job, since we need userland-side POLL... for
  unified {de,}mangle_poll(), thus the cherry-pick at the last step.

  After that we will have:

   - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
     ->poll() still using those will be caught by sparse.

   - eventpoll.c and select.c warning-free wrt __poll_t

   - no more kernel-side definitions of POLL... - userland ones are
     visible through the entire kernel (and used pretty much only for
     mangle/demangle)

   - same behavior as after the first series (i.e. sparc et.al. epoll(2)
     working correctly)"

* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  annotate ep_scan_ready_list()
  ep_send_events_proc(): return result via esed->res
  preparation to switching ->poll() to returning EPOLL...
  add EPOLLNVAL, annotate EPOLL... and event_poll->event
  use linux/poll.h instead of asm/poll.h
  xen: fix poll misannotation
  smc: missing poll annotations

Pull xtense fix from Max Filippov:
 "Build fix for xtensa architecture with KASAN enabled"

* tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix build with KASAN

Pull nios2 update from Ley Foon Tan:

 - clean up old Kconfig options from defconfig

 - remove leading 0x and 0s from bindings notation in dts files

* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: defconfig: Cleanup from old Kconfig options
  nios2: dts: Remove leading 0x and 0s from bindings notation

The commit 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h

Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

Remove old, dead Kconfig option INET_LRO. It is gone since
commit 7bbf3cae ("ipv4: Remove inet_lro library").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>

Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +

For simplicity, two sed expressions were used to solve each warnings separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>

Pull PCI fix from Bjorn Helgaas:
 "Fix a POWER9/powernv INTx regression from the merge window (Alexey
  Kardashevskiy)"

* tag 'pci-v4.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  powerpc/pci: Fix broken INTx configuration via OF

Pull block fixes from Jens Axboe:
 "A few fixes to round off the merge window on the block side:

   - a set of bcache fixes by way of Michael Lyle, from the usual bcache
     suspects.

   - add a simple-to-hook-into function for bpf EIO error injection.

   - fix blk-wbt that mischarectized flushes as reads. Improve the logic
     so that flushes and writes are accounted as writes, and only reads
     as reads. From me.

   - fix requeue crash in BFQ, from Paolo"

* tag 'for-linus-20180210' of git://git.kernel.dk/linux-block:
  block, bfq: add requeue-request hook
  bcache: fix for data collapse after re-attaching an attached device
  bcache: return attach error when no cache set exist
  bcache: set writeback_rate_update_seconds in range [1, 60] seconds
  bcache: fix for allocator and register thread race
  bcache: set error_limit correctly
  bcache: properly set task state in bch_writeback_thread()
  bcache: fix high CPU occupancy during journal
  bcache: add journal statistic
  block: Add should_fail_bio() for bpf error injection
  blk-wbt: account flush requests correctly

Pull x86 platform driver updates from Darren Hart:
 "Mellanox fixes and new system type support.

  Mostly data for new system types with a correction and an
  uninitialized variable fix"

[ Pulling from github because git.infradead.org currently seems to be
  down for some reason, but Darren had a backup location    - Linus ]

* tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86:
  platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
  platform/x86: mlx-platform: Add support for new msn201x system type
  platform/x86: mlx-platform: Add support for new msn274x system type
  platform/x86: mlx-platform: Fix power cable setting for msn21xx family
  platform/x86: mlx-platform: Add define for the negative bus
  platform/x86: mlx-platform: Use defines for bus assignment
  platform/mellanox: mlxreg-hotplug: Fix uninitialized variable

Merge tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform

Pull chrome platform updates from Benson Leung:

 - move cros_ec_dev to drivers/mfd

 - other small maintenance fixes

[ The cros_ec_dev movement came in earlier through the MFD tree  - Linus ]

* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
  platform/chrome: Use proper protocol transfer function
  platform/chrome: cros_ec_lpc: Add support for Google Glimmer
  platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
  platform/chrome: cros_ec_lpc: remove redundant pointer request
  cros_ec: fix nul-termination for firmware build info
  platform/chrome: chromeos_laptop: make chromeos_laptop const

Pull KVM updates from Radim Krčmář:
 "ARM:

   - icache invalidation optimizations, improving VM startup time

   - support for forwarded level-triggered interrupts, improving
     performance for timers and passthrough platform devices

   - a small fix for power-management notifiers, and some cosmetic
     changes

  PPC:

   - add MMIO emulation for vector loads and stores

   - allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
     requiring the complex thread synchronization of older CPU versions

   - improve the handling of escalation interrupts with the XIVE
     interrupt controller

   - support decrement register migration

   - various cleanups and bugfixes.

  s390:

   - Cornelia Huck passed maintainership to Janosch Frank

   - exitless interrupts for emulated devices

   - cleanup of cpuflag handling

   - kvm_stat counter improvements

   - VSIE improvements

   - mm cleanup

  x86:

   - hypervisor part of SEV

   - UMIP, RDPID, and MSR_SMI_COUNT emulation

   - paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit

   - allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
     AVX512 features

   - show vcpu id in its anonymous inode name

   - many fixes and cleanups

   - per-VCPU MSR bitmaps (already merged through x86/pti branch)

   - stable KVM clock when nesting on Hyper-V (merged through
     x86/hyperv)"

* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
  KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
  KVM: PPC: Book3S HV: Branch inside feature section
  KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
  KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
  KVM: PPC: Book3S PR: Fix broken select due to misspelling
  KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
  KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
  KVM: PPC: Book3S HV: Drop locks before reading guest memory
  kvm: x86: remove efer_reload entry in kvm_vcpu_stat
  KVM: x86: AMD Processor Topology Information
  x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
  kvm: embed vcpu id to dentry of vcpu anon inode
  kvm: Map PFN-type memory regions as writable (if possible)
  x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
  KVM: arm/arm64: Fixup userspace irqchip static key optimization
  KVM: arm/arm64: Fix userspace_irqchip_in_use counting
  KVM: arm/arm64: Fix incorrect timer_is_pending logic
  MAINTAINERS: update KVM/s390 maintainers
  MAINTAINERS: add Halil as additional vfio-ccw maintainer
  MAINTAINERS: add David as a reviewer for KVM/s390
  ...

59f47eff ("powerpc/pci: Use of_irq_parse_and_map_pci() helper")
replaced of_irq_parse_pci() + irq_create_of_mapping() with
of_irq_parse_and_map_pci(), but neglected to capture the virq
returned by irq_create_of_mapping(), so virq remained zero, which
caused INTx configuration to fail.

Save the virq value returned by of_irq_parse_and_map_pci() and correct
the virq declaration to match the of_irq_parse_and_map_pci() signature.

Fixes: 59f47eff "powerpc/pci: Use of_irq_parse_and_map_pci() helper"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull more Kbuild updates from Masahiro Yamada:
 "Makefile changes:
   - enable unused-variable warning that was wrongly disabled for clang

  Kconfig changes:
   - warn about blank 'help' and fix existing instances
   - fix 'choice' behavior to not write out invisible symbols
   - fix misc weirdness

  Coccinell changes:
   - fix false positive of free after managed memory alloc detection
   - improve performance of NULL dereference detection"

* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
  kconfig: remove const qualifier from sym_expand_string_value()
  kconfig: add xrealloc() helper
  kconfig: send error messages to stderr
  kconfig: echo stdin to stdout if either is redirected
  kconfig: remove check_stdin()
  kconfig: remove 'config*' pattern from .gitignnore
  kconfig: show '?' prompt even if no help text is available
  kconfig: do not write choice values when their dependency becomes n
  coccinelle: deref_null: avoid useless computation
  coccinelle: devm_free: reduce false positives
  kbuild: clang: disable unused variable warnings only when constant
  kconfig: Warn if help text is blank
  nios2: kconfig: Remove blank help text
  arm: vt8500: kconfig: Remove blank help text
  MIPS: kconfig: Remove blank help text
  MIPS: BCM63XX: kconfig: Remove blank help text
  lib/Kconfig.debug: Remove blank help text
  Staging: rtl8192e: kconfig: Remove blank help text
  Staging: rtl8192u: kconfig: Remove blank help text
  mmc: kconfig: Remove blank help text
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull misc vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: fix incomplete reset on read from zero offset
  kernfs: fix regression in kernfs_fop_write caused by wrong type

This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done.  So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>