Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6313/

Some devices have power LED as well as status LED. The second one is
used to show the firmware is up and running. Set "timer" trigger for
such LEDs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6312/

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6310/

With this patch we prevent the irq from being fired when it is
registered. The Hardware fires an IRQ when input signal XOR polarity
AND gpio mask is 1. Now we are setting polarity to a vlaue so that is
is 0 when we register it.

In addition we also set the irq mask register to 0 when the irq handler
is initialized, so all gpio irqs are masked and there will be no
unexpected irq.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6304/

BUG() can be a noop if CONFIG_BUG is not selected,
leading to the following build problem on a randconfig:

arch/mips/bcm63xx/cpu.c: In function 'detect_cpu_clock':
arch/mips/bcm63xx/cpu.c:254:1: error: control reaches end of
non-void function [-Werror=return-type]

We fix this problem by replacing BUG() with panic() since it's
best to handle the case of an unknown board instead of silently
returning a random clock frequency.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5932/

This old wgt634u.c was trying to implement a bit ugly support for
Netgear WGT634U. It provided info about LED, flash mapping & layout and
was trying to handle reset button.

This is not needed anymore as we have replacement for all this stuff.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6302/

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6298/

This includes all devices from OpenWrt's "diag" that we support in arch
code (we have entries for in enum bcm47xx_board).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6301/

So far this adds support for one Netgear model only, but it's designed
and ready to add many more device. We could hopefully import database
from OpenWrt.
Support for SSB is currently disabled, because SSB doesn't implement IRQ
domain yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6300/

So far this is mostly just a proof of concept, database consists of a
single device. Creating a nice iterateable array wasn't an option
because devices have different amount of LEDs. And we don't want to
waste memory just because of support for a device with dozens on LEDs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6299/

The BCM4706 has a problem with the CPU wait instruction. When r4k_wait
or r4k_wait_irqoff is used will just hang and not return from a
msleep(). Removing the cpu_wait functionality is a workaround for this
problem. The BCM4716 does not have this problem.

The BCM4706 SoC uses a MIPS 74K V4.9 CPU.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6288/

This will add the board name to the machine entry in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5864/

Move wakeup to after early console. This will allow us to display error
messages when cores are not woken up.  Also reduce the wait time for core
to come up.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6303/

The early serial code is not needed because we already have early
printk support provided by common/earlycons.c

This change also fixes the following build error that occurs when
CONFIG_SERIAL_8250 is not configured for Netlogic XLR boards:

arch/mips/built-in.o: In function `nlm_early_serial_setup':
setup.c:(.init.text+0x274): undefined reference to `early_serial_setup'
make: *** [vmlinux] Error 1
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6083/

Add a default device tree fie for XLP9XX boards, and add code to use
this device tree if no DTB is passed to the kernel.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6287/

Support for adding legacy IRQ domain for XLP9XX. The node id of the
PIC has to be calulated differently for XLP9XX.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6286/

XLP9XX has a USB 3.0 controller on-chip with 2 xHCI ports. The USB
block is similar to the one on XLP2XX, so update usb-init-xlp2.c
to handle XLP9XX as well.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6285/

Add PCI support for Netlogic XLP9XX. The PCI registers and
SoC bus numbers have changed in XLP9XX.

Also skip a few (bus,dev,fn) combinations which have issues when
read.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6284/

XLP9XX has 20 cores per node, opposed to 8 on earlier XLP8XX.
Update code that calculates node id from cpu id to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6283/

Update bridge code. Add code to the XLP9XX registers for DRAM
size, limit and node when running on XLPXX
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6282/

Update IO offset of the early console UART.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6281/

Add the SYS block registers for XLP9XX, most of them have changed.
The wakeup sequence has been updated to set the coherent mode from
the main thread rather than the woken up thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6280/

Functions for the XLP9XX interrupt table entry format and other PIC
register changes.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6279/

Most IO block offsets have changed in XLP9XX. Update iomap.h to add the
new addresses of different SoC blocks like PIC, SYS, UART etc. that are
needed by the base code.

On XLP9xx, the SoC blocks of other nodes are seen on a PCI bus
corresponding to the node. Update iomap code to reflect this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6277/

Adds processor ID of XLP 9XX to asm/cpu.h.  Update netlogic/xlp-hal/xlp.h
to add cpu_is_xlp9xx() and to update cpu_is_xlpii() to support XLP 9XX.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6274/

Use the FUSE register to get the list of active cores in the CPU
instead of using the CPU reset register, this is the recommended
method.

Also add code to mask the coremask with the default number of cores
for each processor series.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6275/

Add macro nlm_node_present() that can be used to check if a node is present
in a multi-chip configuration. This can be used even when NUMA is not enabled.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6272/

On XLPII CPUs, the L1D cache has to be flushed with regular cache
operations before enabling threads in a core.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6276/

No change in logic, the changes are:
* cleanup some whitespace and comments
* remove confusing argument of SYS_CPU_COHERENT_BASE macro
* make the numerical labels in macros consistent
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6273/

Add mach-netlogic/topology.h which contains XLP cpu number to core and
node mapping.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6271/

Add MSI chip and MSIX chip definitions.

For MSI, we map the link interrupt to a MSI link IRQ which will
do a second level of dispatch based on the MSI status register.

The MSI chip definitions use the MSI enable register to enable
and disable the MSI irqs.

For MSI-X, we split the 32 available MSI-X vectors across the
four PCIe links (8 each). These PIC interrupts generate an IRQ
per link which uses a second level dispatch as well.

The MSI-X chip definition uses the standard functions to enable
and disable interrupts.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6270/

Boot log says:

pci 0000:00:0a.3: no compatible bridge window for [io  0x1000-0x103f]
pci 0000:00:0a.3: no compatible bridge window for [io  0x1100-0x110f]

The io resource starting point on Malta was modified by c5de50da (MIPS:
Malta: Change start address to avoid conflicts.) to avoid conflicts with
ACPI and SMB devices. In fact, that was not needed (and now causing
southbridge ACPI missing) since 166c6370 (PCI: add pci_create_root_bus()
that accepts resource list) and 7c090e5b (mips/PCI: convert to
pci_scan_root_bus() for correct root bus resources) had already done the
correct fix.

This patch actually reverts the change made by c5de50da. And with this
fix, log says:

pci 0000:00:0a.3: quirk: [io  0x1000-0x103f] claimed by PIIX4 ACPI
pci 0000:00:0a.3: quirk: [io  0x1100-0x110f] claimed by PIIX4 SMB

These things may not be used but as part of platform resources are better
off to be included.

Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6037/

Currently the supported ISA is only printed on the latest architectures.
Print it also on legacy platforms.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6295/

The platform data already available in tree for JZ4740 USB Device
Controller was previously used by an out-of-tree USB gadget driver
which was not relying on the musb driver and was written by Ingenic
and the Qi-Hardware community.

Update platform data for JZ4740 USB device controller to be used with
musb driver.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6265/

This patch removes CONFIG_MTD_PARTITIONS in config files for MIPS.
 Because CONFIG_MTD_PARTITIONS was removed by commit 6a8a98b2.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6162/Signed-off-by: Eunbong Song <eunb.song@samsung.com>

There is already an init_dsp function which checks cpu_has_dsp & calls
__init_dsp if it does. Make use of it instead of duplicating the same
code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6148/

This patch cleans up the declaration of the resume function by replacing
void pointers with their correct types. The irrelevant & incorrect
comment preceeding the resume function is replaced by one documenting
its function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6146/

Add defconfig for the Ben NanoNote handheld computer which is built
around QI_LB60 board and Ingenic JZ4740 MIPS SoC.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6257/

Input GPIO changes can generate interrupts, but we need kind of ACK for
them by changing IRQ polarity. This is required to stop hardware from
keep generating interrupts and generate another one on the next GPIO
state change.
This code allows using GPIOs with standard interrupts and add for
example GPIO buttons support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6216/

The file uses u16 type but doesn't include its definition explicitly

I was getting this error when including this header in my driver:

  arch/mips/include/asm/mipsregs.h:644:33: error: unknown type name ‘u16’
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6212/