The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver is mandatory for proper operation on the platforms covered
by the ARCH_BCM_MOBILE Kconfig symbol, make sure we do that driver on
for these platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit c5cdcba3.

This adds the initial support of the Broadcom NSP gpio-a driver.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for Broadcom NSP GPIO-a
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

configs is allocated by pinconf_generic_parse_dt_config(),
pinctrl_utils_add_map_configs() duplicates configs so it can and has to
be freed to prevent memory leaks.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

DR needs use the pulse counter direction pin as common gpio
function.
Signed-off-by: Guoying Zhang <Guoying.Zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The vip low 8bit mode and vip high 8 bit mode pin groups had missed
3 pins:vip_vsync, vip_hsync and vip_pxclk. Without these 3 pins, the
vip could not work properly.
Now we add these 3 pins into these two pin groups.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove write-protect and chip-selector pins from nand pin group.
And then create two separate pin groups for these two pin.

So the nand driver can choose correct pin groups as board desgin:
For example:
1. nand without wp&cs:
	nand@17050000 {
		pinctrl-0 = <&nd_df_basic_pmx>;
	};
2. nand with wp
        nand@17050000 {
                pinctrl-0 = <&nd_df_basic_pmx &nd_df_wp_pmx>;
        };
3. nand with cs:
        nand@17050000 {
                pinctrl-0 = <&nd_df_basic_pmx &nd_df_cs_pmx>;
        };
4. nand with wp&cs:
        nand@17050000 {
                pinctrl-0 = <&nd_df_basic_pmx &nd_df_wp_pmx &nd_df_cs_pmx>;
        };
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The sd9 pin mux with sd3 and it is selected by SYS2PCI_SDIO9SEL.
This makes the codes ugly since the register is not in pinctrl
module.
Signed-off-by: Yonghui Zhang <yonghui.zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The nand in atlas7 has two chip select line. But in most time, the
nand only has one chip, so only one chip select line is enough.
The nand driver select this new pin group can free one chip select
line for other modules to avoid pin conflict.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As the pxa architecture, at least for pxa27x, supports pin control,
activate it in the pinctrl tree.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the pxa27x architecture, which is a pxa2xx with 128 pins. The
registers spacing, and pins logic is common to pxa2xx, only the pins and
their alternate function are specific to pxa27x.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pin configuration for pxa2xx architectures. PXA doesn't provide any
bias, push, pull capabilities. The only capability is to set a state for
the pins when the platform enter sleep or deep sleep mode.

The state of a pin is set by :
 - whether the GPIO direction was input or output
 - if it is output, a register set programs whether the pin should be
   held to ground or VccIO
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The driver is inspired from the sunxi driver. The pxa architecture
specificities leading to the driver are :
 - each pin has 8 possible alternate functions
 - 4 of these are output kind
 - 4 of these are input kind
 - there is always a "gpio input" and "gpio output" function
 - the function matrix is very scattered :
   - some functions can be found on 5 different pads
   - the number of functions is greater than the number of pins
   - there is no "topology" grouping of pins (such as all SPI in one
     corner of the die)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add a pincontrol driver for pxa2xx architecture, encompassing all pxa25x
and pxa27x variants. This is only the pin muxing part of the driver.

One specific consideration is also the memory space (MMIO), which is
intertwined with the GPIO registers. To make things worse, the GPIO
direction register also affect pin muxing, as it chooses the "kind" of
pin, ie. the 4 output functions or 4 input functions.

The mapping between pinctrl notions and PXA Technical Reference Manual
is as follows :
 - a pin is obviously a pin
 - a group is also a pin, ie. group P101 is the pin 101
 - a mux function is an alternate function
   (ie. gpio-in, gpio-out, MMCLK, BTRTS, etc ...)

The individual architecture (pxa27x, pxa25x) instantiate a pin control
by providing a table of pins, each pin being provided a list of
PXA_FUNCTION (alternate functions).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the pinctrl pxa drivers to the pxa maintained files.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'sh-pfc-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

Common MVEBU pinctrl driver core gets an array of controls to modify
a specific set of registers and an array of modes for each pingroup
from each of the different SoC families of MVEBU.

Some SoC families comprise different variants that differ in available
pingroups and also controls, but to ease driver development, we can
pass a variant mask to disable specific pingroups for some variants.
However, controls are limited to the true number of pinctrl groups
avaiable on a variant.

Now, when pinctrl core driver parses over above arrays, it tries to
match modes with available controls and complains about missing
controls for modes that are passed to the core but actually are not
avaiable on a variant with:

kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36

This warning is a false-positive and annoying, so move the warning
after we checked the variant mask for each mode setting. Also, if
there is no supported setting for this variant, do not complain at
all.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Add pins, groups, and a function for SCIF_CLK, which is the external
clock source for the Baud Rate Generator for External Clock (BRG) on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Add pins, groups, and a function for the 4 MSIOF devices.

Note that the pin function name of MSIOF3 is named BBIF1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The 12 data pins of LCD2 are numbered 0..11, not 0..12.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The 12 data pins of LCD1 are numbered 0..11, not 0..12.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The 8 data pins of the Compact Flash Interface are numbered 0..7, not
0..8.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Extracted from a big patch by Takeshi Kihara.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Correct MSIOF3 TXD_A/RXD_A pins]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Pins that (1) can be configured as either GPIO or a single peripheral
function, and (2) that don't need configuration in an IPSRx register,
should still be listed in the pinmux_data[] array.

Else selecting the peripheral function fails with e.g.:

    sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1281

(mark 1281 is MSIOF0_SCK_MARK).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The group size for registers PADCFGLOCK, HOSTSW_OWN, GPI_IS,
GPI_IE, are not 24 for Broxton, Add a parameter to allow
different platform to set correct value.
Signed-off-by: Qi Zheng <qi.zheng@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The returned configs from pinconf_generic_parse_dt_config() is
duplicated from original. Make it clear it must be freed when no
longer necessary.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

CONFIG_PINCTRL_SPEAR is more suitable than CONFIG_PLAT_SPEAR
to guard the drivers/pinctrl/spear/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

CONFIG_PINCTRL_MVEBU is more suitable than CONFIG_PLAT_ORION
to guard the drivers/pinctrl/mvebu/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

CONFIG_PINCTRL_BERLIN is more suitable than CONFIG_ARCH_BERLIN
to guard the drivers/pinctrl/berlin/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>