Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This makes it clear that generic_buffer is an IIO tool
and also complies with filename conventions in tools/iio.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add options to the Makefile for install/uninstall similar to other tools.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it down.
Use iio_device_claim_direct_mode() to guarantee device stays
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Use SMBus "block read" protocol only when supported by adapter.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove st_sensors_get_buffer_element symbol export since not explicitly
used outside of st_sensors driver.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf

Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This structure has not been optional for a long time (if ever) but the
code implies that it is.  As we then use it later in a fashion that would
crash if it was in fact NULL, it's inconsistent so fix it up by removing
unnecessary checks.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add datasheet names for ADC channels to allow iio consumers access.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Enable humidity support for the BME280 part
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This driver does not call i2c_smbus_read|write_byte_data(),
so remove the corresponding functionality test. It uses regmap
to handle byte transfers transparently.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Matt Ranostay <matt.ranostay@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The Nuvoton NAU7802 ADC is able to adjust its gain but prior knowledge of
its possible values was required to adjust it. Users had to guess the
possible gain values based on the ADC datasheet or on this driver's code.

This exposes the possible values in the in_voltage_scale_available file of
each nau7802 ADC device. The gain is set for the whole ADC and is therefore
not configurable by channel. Thus, there exists only one
in_voltage_scale_available file for each nau7802 ADC device even if it has
two separate channels.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add implementation for Maxim MAX5487, MAX5488, MAX5489
digital potentiometers.

Datasheet:
http://datasheets.maximintegrated.com/en/ds/MAX5487-MAX5489.pdfSigned-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
CC: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.

The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

TI ADS1115 is a 16-bit resolution ADC that is register map
compatible with the ADS1015 device.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

BMM150 is register compatible with magnetometer part of
BMC156.

Datasheet is at:
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdfSigned-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:

http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF

Includes:
- raw readings
- ACPI detection
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Actually I2C_FUNC_SMBUS_WORD_DATA isn't need for this device, and regmap
handles all single byte reads transparently.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds the following sysfs files according to the iio ABI:

-rw-r--r--    4096 in_accel_oversampling_ratio
-r--r--r--    4096 in_accel_oversampling_ratio_available

Internally, the device knows about 4 different power modes that differ
in oversampling ratio (and power consumption). We just show the user
what oversampling ratio(s) is/are available, depending on the current
frequency.

The referenced table in the datasheets makes it easier to understand.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

We register a new device type named "dummy", this will create a
configfs entry under:
	* /config/iio/devices/dummy.

Creating dummy devices is now as simple as:

$ mkdir /config/iio/devices/dummy/my_dummy_device
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This is similar with support for creating triggers via configfs.
Devices will be hosted under:
	* /config/iio/devices

We allow users to register "device types" under:
	* /config/iio/devices/<device_types>/
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Rename this definition, no functional changes.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

These definitions are not currently used and if the functionality
they represent is needed the values should be added back to a table
for easy userspace use.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The current channel number for the LEDs should match the stage
number that they are active during, fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Currently the TIA gain settings are exported to userspace as sysfs
entries that do not clearly represent their internal relation to the
sampling stages. The gain settings are enabled on a per-stage basis,
this can be seen in figure 24 of the current AFE4404 datasheet.
These gain settings should therefore be tied to the channels that are
read during these stages. Make this change here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

These drivers can use regmap fields to access fields in registers, this
allows us to remove some macros/defines and simplify code, do this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

These AFEs have 4 ADC mesuring stages (called LED2, ALED2, LED1, and
ALED1 in the datasheet), we map these as channels, these stages can serve
different purposes depending on the application. For instance the AFE4404
has an additional LED (LED3), this LED can be timed to be active during
stage 2 (or anystage, but the datasheet describes this case and the name
of the stage reflects this use). This ability is used further in upcoming
parts that tie the front-end gain and the LED timings together. For these
reasons we remove explicit naming the channels.

Without channel names it is best that the index numbers are in order to
match the stage number, reorder the channel numbers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Input channel LED3 is only an alias for stage ALED2, this virtual channel
does nothing for us, remove this channel.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

No channel in the afe4403 driver has IIO_CHAN_INFO_OFFSET set so
remove the handlers for this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>